Instruction/ maintenance manual of the product CE-99200 Fusion
Go to page of 9
CE-SS200 INST ALLA TION MANUAL VEHICLE SECURITY SYSTEM.
2 3 TABLE OF CONTENTS • PROGRAMMING REMOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 4 • ALARM FEATURES PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . pg 5 • ADJUSTING THE SENSITIVITY LEVEL . . . . . . .
4 5 PROGRAMMING REMOTES 1. Turn the ignition switch ‘OFF/ON’ 3 times (within 15 seconds) and leave in the ON position. 2. Push the valet switch 3 times, and hold on the 3rd push until a long chirp is heard from the siren, and then release the valet switch.
6 7 ALARM FEATURE “II” PROGRAMMING: 1. Turn the Ignition ‘switch ‘ON/OFF’ 3 times (within 15 seconds), and leave in the OFF position. 2. Push the valet switch 4 times and hold on the 4th push until two short chirps and one long chirp is heard, and then release the valet switch.
8 9 WIRING DIAGRAM A: MAIN 6 PIN WIRE HARNESS: 6P i nM i n i C o n n e c t o r Black Ant enna W i re LED Indi cat or Val e t Swi t c h 2P i n Blue 2P i n Wh i t e 6P i n Wh i t e Mai n 6 Pi n Wi re h ar n es s 6P i n Wh i t e 6P i nD o o rL o c k / U n l o c k W ire harn ess 6P i n Wh i t e 6.
10 11 6. Red/White Wire: (-) 200mA Programmable Output 2. Blue Wire: Instant Tri gger Ground Input 1. V iolet W ire: P ositive D oor P in Switc h Inpu t 4.
12 13 +12V Master Door Loc k Swi tc h X X Splice Splice Cut the Existing Loc k Wire To D o o r Loc k To S l a v e D o o r Lock s witches Green / white Green/ red Cut the Existi ng Unlock Wire Blue/ wh.
14 15 PUBLISHED BY FUSION ELECTRONICS LIMITED: © Copyright 2007 by FUSION Electronics Limited. All rights reserved. Specifications and design are subject to change without notice. Cut Existing Unlock X Lock Unlock OEM Door Master Lock To All Other Door Lock Motors Red / White OEM Driver's Door Lock Motor +1 2 V Blue / Red Existing Pos.
• • Specifications and design are subject to change without notice • •.
An important point after buying a device Fusion CE-99200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fusion CE-99200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fusion CE-99200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fusion CE-99200 you will learn all the available features of the product, as well as information on its operation. The information that you get Fusion CE-99200 will certainly help you make a decision on the purchase.
If you already are a holder of Fusion CE-99200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fusion CE-99200.
However, one of the most important roles played by the user manual is to help in solving problems with Fusion CE-99200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fusion CE-99200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
