Instruction/ maintenance manual of the product RX600 S3 Fujitsu Siemens Computers
Go to page of 17
PRIMERGY RX6 00 S3 incl. SAS version System configurator and order-information guide Contents Instructions Configuration diagram Configurator 0 0 System software 1 I Basic unit 2 II Processor 3 III Me.
System configurator and order-information guide PRIMERGY RX600 S3 Status 2007-01-24 Instructions This document contains basic product and configuration information that will enable you to configure yo.
System configurator and order-information guide PRIMERGY RX600 S3 Status 2007-01-24 Configuration diagram PRIMERGY RX600 S3 TOP View System unit ( I ) Extension slots Memory ( III ) SCSI / RAID controller ( VIII ) Fiber Channel ( IX ) Communication/Network ( X ) 7 6 5 4 Processors must be plugged in order according the picture.
PRIMERGY-Software Configurators and Release Lists Start "PRIMERGY RX600 S3" PRIMERGY RX600 S3 Status 2007-01-24 SW - Configurator 32 bit with OEM-Software without OEM-Software for PRIMERGY S.
PRIMERGY-Software Configurators and Release Lists Start "PRIMERGY RX600 S3" PRIMERGY RX600 S3 Status 2007-01-24 SW Configurator EM64T with OEM-Software without OEM-Software for PRIMERGY Serv.
System configurator and order-information guide Start PRIMERGY RX600 S3 PRIMERGY RX600 S3 Status 2007-01-24 Section I Basic unit PRIMERGY RX600 S3 SCSI PRIMERGY RX600 S3 SAS Rack unit 4U Rack unit 4U .
System configurator and order-information guide A PRIMERGY RX600 S3 Status 2007-01-24 Section II Processor A 4-way processor system requires a multi-processor operating system Later upgrading to a four-way-processor system is also possible VRM´s for 1st/2nd CPU are on the Motherboard, for the 3nd / 4th CPU addition VRM Modules are required.
System configurator and order-information guide B PRIMERGY RX600 S3 Status 2007-01-24 Section III Memory The system can be equipped with up 4 memory boards with 2 memory banks each. One Memory Board is allready supplied in the base unit. Each memory board can be equipped with up to 2x 8GB = 16GB memory.
System configurator and order-information guide C PRIMERGY RX600 S3 SAS Status 2006-12-31 Section IV on-board SCSI / SAS Controller SCSI Base Units The system is equipped with a two channel Utra 320 onboard SCSI controller including a full featured RAID controller with 256MB Cache (suporting the RAID level 0, 1, 5, 10, 50).
System configurator and order-information guide D PRIMERGY RX600 S3 Status 2007-01-24 SAS Base Units AB. on-board SCSI-/ SAS RAID-Controller for accessible drives and SAS HDD´s -> SAS Version The .
System configurator and order-information guide E PRIMERGY RX600 S3 Status 2007-01-24 Section V USB devices / optical devices One of the following USB devices must be used for integrating the drivers during installation process if no automized (e.
System configurator and order-information guide F PRIMERGY RX600 S3 Status 2007-01-24 Section VII Tapes devices S26361-F3128-E101 internal SCSI-Cable for connetion of internal Tape devices max.
System configurator and order-information guide G PRIMERGY RX600 S3 Status 2007-01-24 Section VIII optional SCSI / RAID controller B. SCSI - controller for internal and external devices. S26361-F2399-E1 1-channel SCSI U160 Controller Adaptec 29160 plug: internal: HD 50-pin & HD68 max.
System configurator and order-information guide H PRIMERGY RX600 S3 Status 2007-01-24 Section IX Fibre channel controller Qlogic controller Emulex Controller No mix and match for Qlogic and S26361-F30.
System configurator and order-information guide I PRIMERGY RX600 S3 Status 2007-01-24 Section X Communication / Network on-board LAN Controller Teaming: Failover, Load Balancing Dual Gbit Ethernet Contr.
System configurator and order-information guide J PRIMERGY RX600 S3 Status 2007-01-24 Section XI System Management Products (RemoteView) S26361-F1790-E221 S26361-F2425-E103 RemoteView Software V5.
System configurator and order-information guide PRIMERGY RX600 S3 Status 2007-01-24 Change Report Date Order number Changes 2007-01-24 S26361-F3124-E200 VRM module for 3rd/4th CPU - no longer available 2007-01-24 S26361-F3124-E361 Processor Xeon MP 3.
An important point after buying a device Fujitsu Siemens Computers RX600 S3 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fujitsu Siemens Computers RX600 S3 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fujitsu Siemens Computers RX600 S3 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fujitsu Siemens Computers RX600 S3 you will learn all the available features of the product, as well as information on its operation. The information that you get Fujitsu Siemens Computers RX600 S3 will certainly help you make a decision on the purchase.
If you already are a holder of Fujitsu Siemens Computers RX600 S3, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fujitsu Siemens Computers RX600 S3.
However, one of the most important roles played by the user manual is to help in solving problems with Fujitsu Siemens Computers RX600 S3. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fujitsu Siemens Computers RX600 S3 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
