Instruction/ maintenance manual of the product P/N9359944058 Fujitsu
Go to page of 18
AIR CONDITIONER FLOOR CONSOLE/ UNDER CEILING DUAL TYPE P/N9359944058 Français Español English KEEP THIS MANUAL FOR FUTURE REFERENCE FUJITSU GENERAL LIMITED OPERA TING MANU AL MODE D’EMPLOI MANU AL DE FUNCIONAMIENT O 9359944058_OM_cover.
En-1 CONTENTS SAFETY PRECAUTIONS ....................................... 1 FEA TURES AND FUNCTIONS .............................. 2 NAME OF P ARTS ................................................... 3 PREP ARA TION ....................................
En-2 FEA TURES AND FUNCTIONS AUTOMA TIC OPERA TION ● COOLING MODEL Merely press the ST ART/STOP button, and the unit will begin automatic operation in the Cooling or Dry mode as appropriate, in accordance with the thermostat setting and the actual temperature of the room.
En-3 Fig. 6 Fig. 5 Instructions relating to heating (*) are applicable only to “ HEA T & COOL MODEL ” (Reverse Cycle). NAME OF P AR TS Fig. 4 Fig.
En-4 Fig. 4 Remote Control Unit C SLEEP button D MASTER CONTROL button E SET TEMP ./SET TIME buttons ( ) F Signal T ransmitter G TIMER button H F AN CONTROL button I ST ART/STOP button J AIR FLOW DIRE.
En-5 PREP ARA TION CAUTION! ● T ake care to prevent infants from accidentally swallowing batteries. ● When not using the remote control unit for an extended period, remove the batteries to avoid possible leakage and damage to the unit.
En-6 Example: When set to COOL Example: When set to 88 ° F Example: When set to AUTO T o Select Mode Operation 1 Press the ST ART/STOP button. The indoor unit ’ s OPERA TION indicator lamp (red) will light. The air conditioner will start operating.
En-7 OPERA TION Instructions relating to heating (*) are applicable only to “ HEA T & COOL MODEL ” (Reverse Cycle). * During Heating mode: Set the thermostat to a temperature set- ting that is higher than the current room temperature. The Heating mode will not operate if the thermostat is set lower than the actual room temperature.
En-8 T o Use the ON timer or OFF timer 1 Press the ST ART/STOP button (if the unit is already operating, proceed to step 2). The indoor unit ’ s OPERA TION indicator lamp (red) will light. 2 Press the TIMER button to select the OFF timer or ON timer operation.
En-9 SLEEP TIMER OPERA TION T o Use the SLEEP timer While the air conditioner is operating or stopped, press the SLEEP button. Both the indoor unit’ s OPERA TION indicator lamp (red) and the TIMER indicator lamp (green) will light. To Change the Timer Settings Press the SLEEP button once again and set the time using the SET TIME buttons.
En-10 ADJUSTING THE DIRECTION OF AIR CIRCULA TION Instructions relating to heating (*) are applicable only to “ HEA T & COOL MODEL ” (Reverse Cycle). V ertical (up-down) direction of airflow is adjusted by pressing the remote control unit ’ s AIR FLOW DIRECTION VERTICAL SET button.
En-11 SWING OPERA TION Begin air conditioner operation before performing this procedure. T o select V ertical airflow SWING Operation Press the AIR FLOW DIRECTION VERTICAL SWING button.
En-12 ● Before cleaning the air conditioner , be sure to turn it off and disconnect the power supply cord. ● Be sure the intake grille is installed securely . ● When removing and replacing the air filters, be sure not to touch the heat exchanger , as per - sonal injury may result.
En-13 When two or more air conditioners are installed in a room and the remote control unit is operating an air conditioner other than the one you wish to set, change the signal code of the remote control unit to operate only the air conditioner you wish to set (four selections possible).
En-14 TROUBLESHOOTING Instructions relating to heating (*) are applicable only to “ HEA T & COOL MODEL ” (Reverse Cycle). In the event of a malfunction (burning smell, etc.), immediately stop operation, disconnect the power supply plug, and consult authorized service personnel.
En-15 TROUBLESHOOTING Instructions relating to heating (*) are applicable only to “ HEA T & COOL MODEL ” (Reverse Cycle). Symptom Doesn ’ t operate at all: Poor Cooling (or *Heating) perform.
En-16 OPERA TING TIPS ● Should the power supply to the air conditioner be inter - rupted by a power failure, the air conditioner will restart automatically in the previously selected mode once the power is restored.
En-17 Instructions relating to heating (*) are applicable only to “ HEAT & COOL MODEL ” (Reverse Cycle). * ● During use of the heating mode, the top of the indoor unit may become warm, but this is due to the fact that coolant is circulated through the indoor unit even when it is stopped; it is not a malfunction.
An important point after buying a device Fujitsu P/N9359944058 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fujitsu P/N9359944058 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fujitsu P/N9359944058 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fujitsu P/N9359944058 you will learn all the available features of the product, as well as information on its operation. The information that you get Fujitsu P/N9359944058 will certainly help you make a decision on the purchase.
If you already are a holder of Fujitsu P/N9359944058, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fujitsu P/N9359944058.
However, one of the most important roles played by the user manual is to help in solving problems with Fujitsu P/N9359944058. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fujitsu P/N9359944058 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
