Instruction/ maintenance manual of the product AWU36CX Fujitsu
Go to page of 17
AIR CONDITIONER W ALL MOUNTED TYPE KEEP THIS MANUAL FOR FUTURE REFERENCE FUJITSU GENERAL LIMITED OPERA TING MANUAL MODE D’EMPLOI MANUAL DE FUNCIONAMIENT O P/N9373597018-02 Indoor Unit A WU36CX Outdo.
En-1 CONTENTS SAFETY PRECAUTIONS .......................................... 1 FEA TURES AND FUNCTIONS ................................. 2 NAME OF P AR TS ...................................................... 3 PREP ARA TION ..........................
En-2 FEA TURES AND FUNCTIONS AUTOMA TIC OPERA TION ● COOLING MODEL Merely press the ST ART/STOP button, and the unit will begin automatic operation in the Cooling or Dry mode as appropriate, in accordance with the thermostat setting and the actual temperature of the room.
En-3 Fig. 2 Fig. 3 Fig. 4 Instructions relating to heating (*) are applicable only to “ HEA T & COOL MODEL ” (Reverse Cycle). NAME OF P AR TS Fig.
En-4 Fig. 1 Indoor Unit 1 Operating Control Panel (Fig. 2) 2 MANUAL AUTO button 3 Remote Control Signal Receiver 4 Indicator Lamps (Fig. 3) 5 OPERA TION Indicator Lamp (green .
En-5 PREP ARA TION CAUTION! ● Take care to prevent infants from accidentally swallowing batteries. ● When not using the remote control unit for an extended period, remove the batteries to avoid possible leakage and damage to the unit.
En-6 Example: When set to COOL Example: When set to 86 ° F Example: When set to AUTO T o Select Mode Operation 1 Press the ST ART/STOP button (Fig. 6 L ). The indoor unit ’ s OPERA TION indicator lamp (green or red) (Fig. 3 5 ) will light. The air conditioner will start operating.
En-7 About Mode Operation AUTO: COOLING MODEL ● When the room temperature is 4 ° F higher than the set temperature, the mode will switch between Cooling and Drying. ● During Drying mode operation, F AN set- ting is switched to LOW gentle cooling effect, and the room fan may stop rotat- ing temporarily .
En-8 T o Use the ON timer or OFF timer 1 Press the ST ART/STOP button (Fig. 6 L ) (if the unit is already operating, proceed to step 2). The indoor unit ’ s OPERA TION indicator lamp (green or red) (Fig. 3 5 ) will light. 2 Press the TIMER button (Fig.
En-9 SLEEP TIMER OPERA TION T o Use the SLEEP timer While the air conditioner is operating or stopped, press the SLEEP button (Fig. 6 F ). Both the indoor unit ’ s OPERA TION indicator lamp (gr een or red) (Fig. 3 5 ) and the TIMER indicator lamp (yellow) (Fig.
En-10 1 2 3 4 5 ADJUSTING THE DIRECTION OF AIR CIRCULA TION Instructions relating to heating (*) are applicable only to “ HEA T & COOL MODEL ” (Reverse Cycle). V ertical (up-down) direction of airflow is adjusted by pressing the remote control unit ’ s AIR FLOW DIRECTION VERTICAL SET button.
En-11 SWING OPERA TION Begin air conditioner operation before performing this procedure. T o select V ertical airflow SWING Operation Press the AIR FLOW DIRECTION VER TICAL SWING button (Fig. 6 N ). The SWING indicator lamp (VER TICAL SWING) (Fig. 3 7 ) will light.
En-12 ● Before cleaning the air conditioner , be sure to turn it off and disconnect the power supply . ● T urn off the electrical breaker . ● Be sure the intake filter (Fig. 4 9 ) is installed securely . ● When removing and replacing the intake filters, be sure not to touch the heat exchanger , as personal injury may result.
En-13 SELECTING THE REMOTE CONTROL UNIT SIGNAL CODE When two or more air conditioners are installed in a room and the remote control unit is operating an air conditioner other than the one you wish to set, change the signal code of the remote control unit to operate only the air conditioner you wish to set (four selections possible).
En-14 TROUBLESHOOTING Instructions relating to heating (*) are applicable only to “ HEA T & COOL MODEL ” (Reverse Cycle). In the event of a malfunction (burning smell, etc.), immediately stop operation, turn off the elec- trical breaker or disconnect the power supply plug, and consult authorized service personnel.
En-15 Operation and Performance TROUBLESHOOTING Instructions relating to heating (*) are applicable only to “ HEA T & COOL MODEL ” (Reverse Cycle).
En-16 OPERA TING TIPS ● Should the power supply to the air conditioner be inter - rupted by a power failure, the air conditioner will restart automatically in the previously selected mode once the power is restored.
An important point after buying a device Fujitsu AWU36CX (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fujitsu AWU36CX yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fujitsu AWU36CX - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fujitsu AWU36CX you will learn all the available features of the product, as well as information on its operation. The information that you get Fujitsu AWU36CX will certainly help you make a decision on the purchase.
If you already are a holder of Fujitsu AWU36CX, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fujitsu AWU36CX.
However, one of the most important roles played by the user manual is to help in solving problems with Fujitsu AWU36CX. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fujitsu AWU36CX along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
