Instruction/ maintenance manual of the product ASU12C1 Fujitsu
Go to page of 21
.
Fig. 6 Fig. 8 Fig. 7 OPERA TION SWING TIMER 7 6 5 1 4 8 Fig. 5 Fig. 1 Fig. 2 Fig. 3 Fig. 4 ^ $ # @ % 0 - 9 ! = ~ 3 SLEEP TIMER MASTER CONTROL SET TEMP.
En-1 CONTENTS SAFETY PRECAUTIONS .................................... En-1 FEATURES AND FUNCTIONS ........................... En-4 NAME OF PARTS ............................................... En-5 PREPARATION .........................................
En-2 Do not stay in direct cooling airflow for long periods. ¶ Excessive direct exposure to chilled air could be bad for your health. ¶ Be especially careful when going to bed, and in rooms where infants, aged, or sick people are staying. Do not insert fingers or objects into the outlet port or intake grilles.
En-3 PRECAUTIONS CAUTION Check the condition of the installation for damage. ¶ After lengthy use, arrange for visit by authorized ser- vice personnel to check installation condition. Always turn off power whenever cleaning the air conditioner or changing the air fil- ter.
En-4 FEATURES AND FUNCTIONS AUTOMATIC OPERATION Merely press the START/STOP button, and the unit will be- gin automatic operation in either the Heating, Cooling, Dry, or Monitor modes as appropriate, in accordance with the thermostat setting and the actual temperature of the room.
En-5 NAME OF PARTS Fig. 6 Remote Control Unit & SLEEP button * MASTER CONTROL button ( SET TEMP. /SET TIME button ( / ) ) Signal Transmitter _ TIMER button + FAN CONTROL button ¡ START / STOP button ™ AIR FLOW DIRECTION button £ SWING LOUVER button Rear side (Fig.
En-6 Turn on the Power In the case of a direct line connection, turn on the circuit breaker. Load Batteries (AAA x 2) Press and slide the battery compartment lid on the reverse side to open it. Slide in the direction of the arrow while pressing the mark.
En-7 SLEEP TIMER MASTER CONTROL SET TEMP. SET TIME FAN CONTROL START/STOP COOL SLEEP TIMER MASTER CONTROL SET TEMP. SET TIME FAN CONTROL AUTO SLEEP TIMER MASTER CONTROL SET TEMP. SET TIME FAN CONTROL START/STOP F OPERATION To Select Mode Operation Press the START/STOP button (Fig.
En-8 MASTER CONTROL SET TEMP. SET TIME FAN CONTROL LOW HIGH MASTER CONTROL SET TEMP. SET TIME FAN CONTROL AUTO OPERATION Press the MASTER CONTROL button to select AUTO.
En-9 To Cancel the Timer Use the TIMER button to select “TIMER RESET.” The air conditioner will return to normal operation. To Change the Timer Setting 1 . Follow the instructions given in the section “To Use the ON Timer or OFF Timer” to select the timer setting you wish to change.
En-10 SLEEP TIMER OPERATION Unlike other timer functions, the SLEEP timer is used to set the length of time until air conditioner operation is stopped. To Use the SLEEP Timer While the air conditioner is operating or stopped, press the SLEEP button (Fig.
En-11 CAUTION ÷ Never place fingers or foreign objects inside the outlet ports, since the internal fan operates at high speed and could cause personal injury. ADJUSTING THE DIRECTION OF AIR CIRCULATION Vertical (up-down) direction of airflow is adjusted by pressing the Remote Control Unit's AIR FLOW DIRECTION button.
En-12 To Select SWING Operation Press the SWING LOUVER button (Fig.6 £ ). The SWING Indicator Lamp (orange) (Fig. 3 7 ) will light. In this mode, the Air Flow Direction Louvers will swing automatically to direct the airflow both up and down. To Stop SWING Operation Press the SWING LOUVER button (Fig.
En-13 CLEANING AND CARE WARNING Before cleaning the unit, be sure to stop the unit and disconnect the power. 1. Disconnect the power. 2. Turn off the electrical breaker. ¶ A fan operates at high speed inside the unit, and personal injury could result.
En-14 Cleaning the Intake Grille 1. Open the Intake Grille. 1 Place your fingers at both lower ends of the grille panel, and lift forward; if the grille seems to catch partway through its movement, continue lifting up- ward to remove. 2 Pull past the intermediate catch and open the Intake Grille wide so that it becomes horizontal.
En-15 Cleaning the Air Filter 1. Open the Intake Grille, and remove the Air Filter. Lift up the air filter's handle, disconnect the two lower tabs and pull out. 2. Remove dust with a vacuum cleaner or by washing. After washing, allow to dry thoroughly in a shaded place.
En-16 ÷ If the unit is stopped and then immediately started again, the compressor will not operate for about 3 minutes, in order to prevent fuse blowouts. ÷ Whenever the Power is disconnected and then reconnected to a power outlet, the protection circuit will operate for about 3 minutes, preventing unit operation during that period.
En-17 Items to Check ÷ Has there been a power failure? ÷ Has a fuse blown out, or a circuit breaker been tripped? ÷ Is the POWER switch set to the OFF position? ÷ Is the timer operating? ÷ Is the.
En-18 OPERATING TIPS Temperature and Humidity Range DB : Dry Bulb Temperature WB : Wet Bulb Temperature ÷ If the air conditioner is used under higher temperature conditioner than those listed, the built-in protection circuit may operate to prevent internal circuit damage.
(800) 888-FGAI.
An important point after buying a device Fujitsu ASU12C1 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fujitsu ASU12C1 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fujitsu ASU12C1 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fujitsu ASU12C1 you will learn all the available features of the product, as well as information on its operation. The information that you get Fujitsu ASU12C1 will certainly help you make a decision on the purchase.
If you already are a holder of Fujitsu ASU12C1, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fujitsu ASU12C1.
However, one of the most important roles played by the user manual is to help in solving problems with Fujitsu ASU12C1. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fujitsu ASU12C1 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
