Instruction/ maintenance manual of the product FF-2000 Franke
Go to page of 26
FF 2000 SERIES Pull-Out Spray Faucet Installation guide.
1/8 P AR TS LIST G 19321.XX Handle G R0240.XX Ring cap kit G 1 154 Cartridge G R0356031 F a st e n i n g s e t ( r ub b e r w as h e r , tr i a n g u la r fl a n ge , m e t al w a s h er , t h r ea de d n ut ) G 1463 Flexible hose G 1592.
Faucet installation 1. Remove all contents from the package and check for completeness (see itemized table and picture). NOTE: Call us immediately if you see inconsistencies.
3/8 4. Install the mounting hardware (GR0356031) to the threaded shank in the fol- lowing sequence: 1 - round flat fiber washer 2 - triangular shaped plastic support 3 - flat metal washer 4 - thread brass nut 5 . Assure that the handle and spout are properly aligned in forward position 6.
4/8 7. Attach the valve-holder to the shorter tubing and attach the spray hose to the valve-holder . NOTE: The provided small black rubber washer needs to be installed here. DO NOT use putty or other sealant agents at this joint. 8. Attach approved connector hoses to the two longer copper tubes and connect to water supply valves.
400 mm 5/8 10. Assemble Pull-out Spray . 1. Attach the pull-out spray head to the hose. NOTE: The rubber washer needs to be installed to pr event leakage. 2. Fasten the weight to the hose as shown in picture below .. 3. T est all water lines, fitting and connections for leaks.
6/8 Standard maintenance and trouble shooting Cleaning of the spray head Any deposits which may accumulate on the nozzle can be removed by simply running a finger over the rubber extrusions and then running the water for a few seconds. In ex- treme cases this step may have to be repeated.
7/8 General maintenance Clean aerator periodically . Do not use harsh detergents, solvents, chemical agents, steel wool, etc. that could harm the surface. Clean only with a soft sponge and soapy water . In the case of very hard water , it is necessary to clean and dry the faucet after each use.
Limited lifetime warranty Franke Consumer Products, Inc., Kitchen Systems Division extends the following warranty to the origi- nal purchaser of its faucets effective January 1, 2003.
1/8 P AR TS LIST G 19321.XX Poignée G R0240.XX Anneau de fixage G 1 154 Cartouche G R0356031 S e t d e fi x at i o n ( jo i n t e n g o m m e , b r i d e t r i a n g ul a i r e , b r i d e en m é t a l, j o i n t fi l e t é ) G 1463 Flexible G 1592.
Installation du mitigeur 1. Déballer tous les éléments et vérifier qu’ils soient tous présents. (regardez la table des matières). NOTE: Communiquer immédiatement tout manque ou défaut (1-800-626-5771) ou visitez www .frankeksd.com www .franke-canada.
3/8 4. Installer les éléments de montage ( GR0356031) sur le pied, en les enfilant dans le sens qui suit : 1-Rondelle plate en fibre 2-Support profilé triangulaire en plastique 3-Rondelle plate en métal 4-Dé en laiton 5 . V é r i fi e r q u e l a p o i g n é e e t l e b e c s o i e n t a l i g n é s v e r s l ’ a v a n t .
4/8 7. Fixer le porte-vanne avec le tuyau le plus court et fixer le tuyau flexible de la douche avec le porte-vanne. NOTE : Installer la petite r ondelle en caoutchouc noir e.
5/8 10. Assembler la douchette extractible. 1 - Assembler le soufflet de la douche au flexible NOTE : La r ondelle en caoutchouc doit êtr e absolument mise en place afin d’éviter toute fuite éventuelle. 2 - Monter le contrepoids sur le tuyau flexible, comme indiqué sur la photo ci-des- sous.
6/8 Manipulation recommandée et solutions aux problèmes Nettoyage du soufflet de la douche. Les résidus accumulés sur les parties en caoutchouc doivent-être retiré avec le doigt en fai- sant couler l’eau quelques secondes. En cas de résidus persistants, répéter l’opération.
7/8 Instructions générales Nettoyer régulièrement l’aérateur . N’utilisez pas de détergents, solvants, produits chimiques, éponges métalliques etc.… qui risqueraient d’endommager la surface. Nettoyer en utilisant seulement une éponge douce et d’eau savonneuse.
Conditions de garanties à vie Franke consumer Products. Inc. kitchen systems division étend la durée de sa garantie. A partir du 01 janvier 2003, le produit est garanti à vie ( en référence à la personne ayant acheté le produit.
1/8 P AR TS LIST G 19321.XX Palanca G R0240.XX V irola de fijación G 1 154 Cartucho G R0356031 J u eg o d e fij a c i ò n ( m o n d a na d e g om a , a r a nd o l a t ri a n g u l ar ,m o n d an a d e me t a l , t ur c a d e m o n t a j e) G 1463 Flexible G 1592.
Instalaciòn del Mezclador 1. Remover l’embalaje de todos los elementos y averiguar que no hay partos faltan- tes ( se vean mesa y estallado correspondientes) NOT A: Comunicar enseguida cualquier falta o defecto ( 1-800-626-5771) o visitar: www .frankeksd.
3/8 4. Instalar a los miembros de montaje (GR0356031) sobre el tallo fileteado en la secuencia aquiì bajo indicada: 1 – mondana plana rotonda en fibra Respaldo perfilado triangular de plàstico 2 – Respaldo perfilado triangular de plàstico 3 – Mondana plana en metal 4 – Dado fileteado de latòn 5 .
4/8 7. Conectar el porta-válvula al tubo màs corto y conectar lo flexible del boccetta al porta-válvula. NOT A: la pequena mondana de goma negra dotada tendrè que ser instalada aquì.
5/8 10. Ensamblar el boccetta estraibile 1. Conectar el sofiòn del boccetta a lo flexible NOT A: No olvides la mondana de goma que tiene que ser montada para evitar eventuales pèrdidas. 2. Montar como el contrappeso sobre lo flexible indicado en la figura aquì bajo 3.
6/8 Manutenciòn ordinaria e investiga averìas Limpieza del sòfion del duchita Cada resto acumulado sobre las partes de goma tenderà que ser removido sencillamente con un dedo y haciendo correr l’ agua por algunos segundo. En caso de resto persistente, repetir l’ operaciòn.
7/8 Manutenciòn general Limpiar periodicamente l’ aerador . No utilices deter gentes agresivos, solvents, agents quìmicas esponjas metàlicas,ecc. Què pueden perjudicar la superficie. Limpiar sòlo utilizzando una esponga blanda y agua jabonadura.
Condiciones de garantìa limitada a vida Franke Consumer Products. Inc. Kitchen Systems Division extiende la presente garantìa limitada al comprador original de sus grifos a partir del 1 enero 2003.
ET 38124 - R3.
An important point after buying a device Franke FF-2000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Franke FF-2000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Franke FF-2000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Franke FF-2000 you will learn all the available features of the product, as well as information on its operation. The information that you get Franke FF-2000 will certainly help you make a decision on the purchase.
If you already are a holder of Franke FF-2000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Franke FF-2000.
However, one of the most important roles played by the user manual is to help in solving problems with Franke FF-2000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Franke FF-2000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
