Instruction/ maintenance manual of the product FD-4 Fostex
Go to page of 100
Owner ’ s Manual Model Digital Multitracker MON L MON R MON L MON R MON L MON R MON L MON R 0 000 0000 0 0 0 0 0 0 0 0 0 0 0 0 UNDO/ PUNCH AUTO LEVEL LEVEL MASTER 01 0 2 0 10 1 01 0 SELECTOR PAN LOW.
Safety Instructions 2 CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER - SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN "WARNING" "TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
T able of contents 3 Introduction.............................................................................4 Main features...........................................................................4 Recording Preparation Connecting a SCSI drive....
4 Introduction/Main features Introduction Thank you for choosing the Fostex FD-4. The FD-4 is a four-track multitracker equipped with two additional virtual tracks. It uses a SCSI removable disk, such as a Zip cartridge or an MO disk, as a recording media to perform six-track recording and four-track playback.
5 Recording preparation R MON OUT L R MIX OUT L AUX RTN 2 R MONO/L 2 AUX SEND 1 SCSI OUT IN DATA DATA POWER SCSI terminator SCSI cable SCSI connector SCSI drive DRIVE AUTO A.PUNCH SYNC OUT SCSI ABS S MF PGM DRIVE AUTO A.PUNCH SYNC OUT SCSI Recording Preparation • After making the connection, turn on the power to the FD-4 and the SCSI drive.
6 Recording preparation Recording mode Sampling rate Quantization Available recording track in real-time Mastering mode 1 44.1 kHz 16-bit linear 2 3 5 5 DRIVE AUTO A.PUNCH SYNC OUT SCSI DRIVE AUTO A.PUNCH SYNC OUT Flashing Flashing Normal mode 44.1 kHz 32 kHz 16-bit linear DAC * 4 Real tracks + 2 Additional tracks 4 44.
7 Recording preparation DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI 44.1kHz S MF PGM ABS The current drive is a SCSI drive. 1 44.1kHz SETUP SURE? DRIVE AUTO A.PUNCH SYNC OUT SCSI 44.1kHz SETUP SURE? DRIVE AUTO A.PUNCH SYNC OUT SCSI 44.1kHz SETUP SURE? DRIVE AUTO A.
8 Recording preparation 2 3, 6 8 4, 5, 7 8 SCSI DRIVE AUTO A.PUNCH SYNC OUT 44.1kHz SETUP CLK SURE? DRIVE AUTO A.PUNCH SYNC OUT SCSI Flashing 44.1kHz SETUP SURE ? DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI Flashing 44.1kHz SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI 44.
9 Names and Functions 4 3 2 1 INPUT 3 R MON OUT L R ST OUT L AUX RTN 1 R MONO/L AUX RTN 2 R MONO/L 2 AUX SEND 1 4 INSERT 3 INPUT 4 SCSI OUT IN D ATA R RECORDER IN L IN MIDI OUT PUNCH IN/OUT DATA MIDI .
10 Names and Functions 1 2 3 4 5 6 7 8 9 10 11 12 2 1 MON L MON R MON L MON R MON L MON R MON L MON R 0 000 0000 0 0 0 0 0 0 0 0 0 0 0 0 UNDO/ PUNCH AUTO LEVEL LEVEL MASTER 01 0 2 0 10 1 01 0 SELECTOR.
11 Names and Functions 5. Monitor level control knob [MON (INPUT/TRK)] These knobs are used to select signals sent to monitor sections L and R, and to adjust the level of those signals. The following options are available. “TRK” The recorder output signals are sent to the monitor section.
12 Names and Functions 13 14 15 16 17 18 19 20 21 41 23 24 25 27 28 33 32 36 38 39 29 35 34 37 40 22 31 30 UNDO/ PUNCH AUTO PITCH VARI R L SHIFT 4/R 3/L 2/R SEL DISP SEL DIGITAL MUL TITRACKER 1/L CLIP.
13 Names and Functions 16. Display indication select key Pressing this key each time will change the display indication as follows: Refer to pages 7, 56 and 81 for more information on the operation of this key .
14 Names and Functions STOP PLA Y REWIND F FWD UNDO/ PUNCH AUTO PITCH VARI R L SHIFT 4/R 3/L 2/R SEL DISP SEL 1/L CLIPBOARD PLAY LOCATE ABS 0 LOCATE REC END F FWD REWIND PLAY STOP RECORD REDO EDIT START IN OUT AUTO PLAY EXECUTE /YES EXIT /NO HOLD/ STORE END IN OUT PGM SEL AUTO RTN SETUP TIME BASE ACCESS CLIPBOARD AUTO PUNCH AUTO RTN ADD.
15 Names and Functions AUTO PLA Y RTN AUTO PLA Y AUTO RTN AUTO 29.V ari Pitch key [V ARI PITCH/ P .EDIT ] This key toggles Vari Pitch mode on and off. When Vari Pitch mode is on, the “VARI PITCH” indicator lights up on the display, and the FD-4 plays using the current pitch data.
16 Names and Functions 33. Store key [STORE] This key is used to store time values (or bar/beat/clock values) in the memory keys. Press this key, then one of the following keys to store data indicated on the display (including edit data) in the corresponding memory key.
17 Names and Functions 37. Auto Return End key [AUTO R TN END/ PREVIEW ] Use this key to store the start point (AUTO RTN END point) for the Auto Return function and the Auto Repeat function. When you press this key, the FD-4 displays currently-stored data, which you can edit.
18 Names and Functions 4 3 2 1 1 2 1 2 3 4 56 7 8 9 10 11 12 13 14 15 INPUT 3 R MON OUT L R ST OUT L AUX RTN 1 R MONO/L AUX RTN 2 R MONO/L 2 AUX SEND 1 4 INSERT 3 INPUT 4 SCSI OUT IN D ATA R RECORDER IN L IN MIDI OUT PUNCH IN/OUT DATA MIDI POWER 1.
19 Names and Functions 3. AUX Send jacks 1, 2 [AUX SEND 1, 2] (Connector: phone) Connect these jacks to the input of an effect unit. The AUX SEND jacks send out signals selected and adjusted by the AUX send knobs to the connected effect unit.
20 Names and Functions DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI 44.1kHz S MF PGM ABS DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI 44.1kHz 44.1kHz SETUP SURE? DRIVE AUTO A.
21 Names and Functions REMAIN SETUP COMPLETED ! SURE ? MTC OFFSET PGM TEMPO V ARI PITCH 44.1kHz MTC IN LOC DIGIT AL SLA VE MIDI MTC ABS MTC REMAIN ABS LOC MTC IN V ARI PITCH TEMPO PGM 44.1kHz SETUP MTC OFFSET ? BAR S M H CLK DF MB SF SURE COMPLETED ! DRIVE AUTO A.
22 Names and Functions ABS 44.1kHz S M F DRIVE AUTO A.PUNCH SYNC OUT PGM CLK SCSI 44.1kHz M DRIVE AUTO A.PUNCH SYNC OUT MB CLK SCSI REMAIN H S MTC IN 44.1kHz S MF DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI H MTC IN 44.1kHz S MF DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI H 44.
23 Names and Functions DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI DRIVE AUTO A.PUNCH SYNC OUT DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI DRIVE AUTO A.
24 Before Starting Recorded area Non recorded area ABS 0 00M, 00S, 00F 00M, 08S, 00F REC END DISK END 23H, 59M, 59S -002BAR, 1 , 00CLK 001BAR, 1 , 00CLK 01H, 00M, 00S, 00F 01H, 00M, 08S, 00F 00H, 59M,.
25 Before Starting unrecorded area recordable disk area Program 1 ABS 0 23H, 59M, 59S 03M 00S 00F 10M 00S 00F 12M 00S 00F unrecorded area recorded area (2 min.) Y ou can record at any point within 24 hours in ABS Time. REC END The area actually used on the disk Recordable disk area.
26 Before Starting Real tracks Additional tracks T rack 1 T rack 2 T rack 3 T rack 4 T rack L T rack R T rack 1 T rack 2 T rack 3 T rack 4 T rack 1 T rack 2 T rack 3 T rack 4 Monitor section INPUT Tra.
27 Before Starting 1/L 2/R 3/L 4/R LR LR LR LR REC SEL switch P AN knob STEREO BUS L STEREO BUS R ST OUT L, R P AN knobs and stereo bus The FD-4 features a four-channel mixer function that en- ables you to mix four sound sources into a stereo mix.
28 Basic Application (Basic Recording and Playback) Point 1 Point 2 Point 3 Point 4 Point 5 4 3 2 1 Real track 1 Real track 2 Real track 3 Real track 4 EQ EQ This chapter explains how to perform basic recording and playback so that you can get used to operating the FD-4.
29 Basic Application (Basic Recording and Playback) 1 2 3 4 5 6 7 8 8 9 10 11 EQ EQ Setting the switch and knob 1. Set the channel 1 INPUT SEL switch to [INPUT]. The electric guitar signal is routed to the input channel 1 fader. If you connect the instrument to another input jack, set the INPUT SEL switch of the corresponding channel to [INPUT].
30 Basic Application (Basic Recording and Playback) Recording track T rack 1 T rack 2 T rack 3 T rack 4 REC TRACK select key for track READY 1/L is READY .
31 Basic Application (Basic Recording and Playback) 1 2 3 4 5 5 MON L MON R MON L MON R MON L MON R MON L MON R 0 000 M PAN + TRK4 INPUT PAN + TRK3 INPUT PAN + TRK2 INPUT PAN + TRK1 INPUT MON MON MON .
32 Basic Application (Basic Multitrack Recording) T rack 1 -> Drum machine 4 3 2 1 1 2 3 4 8 6 7 10 9 8 11 13 12 EQ EQ You learned how to record one sound source to one track in the “Basic Recording and Playback” chapter.
33 Basic Application (Basic Multitrack Recording) 1 2 3 4 4 EQ EQ 1. Set the channel 1 INPUT SEL switch to [INPUT]. 2. Turn the channel 1 P AN knob all the way to [R]. 3. Press the RECORD RACK select key [2/R] to set track 2 to READY mode. The 2/R LED flashes.
34 Basic Application (Basic Multitrack Recording) INPUT jack REC TRACK select key for track READY 3/L INPUT SEL switch position P AN knob adjustment Set to MON. Monitor section’s SELECTOR position Adjusting the monitoring level of the recording track.
35 Basic Application (Basic Multitrack Recording) 1 2 3 4, 8 6, 13 7 7 9 10 11 5, 12 14 EQ EQ Effect unit 1 Effect unit 2 Master Recorder Setting the switch and knob on the FD-4 1.
36 Handling Programs 1 1 2 3 4 5, 6, 7 DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI 44.1kHz S MF PGM ABS DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI ? SURE DRIVE AUTO A.
37 Handling Programs PGM 01 New PGM 2 3 1 UNDO/ PUNCH AUTO PITCH VARI R L SHIFT 4/R 3/L 2/R SEL DISP SEL DIGITAL MULTITRACKER 1/L CLIPBOARD PLAY LOCATE ABS 0 LOCATE REC END F FWD REWIND PLA Y STOP REC.
38 Handling Programs 44.1kHz SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI 44.1kHz SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI PGM 44.1kHz SETUP DRIVE AUTO A.
39 Handling Programs 44.1kHz SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI 44.1kHz SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI PGM 44.1kHz SETUP DRIVE AUTO A.
40 Special Application (Playback in Vari pitch mode) 1 3 DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI 44.1kHz S MF PGM ABS V ARI PITCH DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI 44.1kHz S M PGM ABS V ARI PITCH % . 2, 6, 7 4 5 EQ EQ This chapter explains how to change the playback speed of the recorder using the Vari Pitch function.
41 Special Application (Recording to a Metronome Sound) 4 3 2 1 INPUT 3 AUX RTN 1 R MONO/L AUX RTN 2 R MONO/L 4 INSERT 3 INPUT 4 2 1 3 4 5 6 EQ EQ Compressor/limiter This chapter explains how to record your performance while you are playing an instrument accompanied by a metro- nome based on the time signature and tempo specified in the Tempo Map.
42 Special Application (Recording to a Metronome Sound) 3 2 4 3 6 8 10 9 1 EQ EQ Checking the metronome sound 1. Select the BAR/BEA T/CLK T ime Base using the TIME BASE SEL switch.
43 Special Application (Punch In/Out Recording) T rack 4 T rack 3 T rack 2 T rack 1 Punch In point Punch Out point This part is changed. T rack 4 T rack 3 T rack 2 T rack 1 What is Punch In/Out recording? Punch In/Out recording enables you to record over previ- ously-recorded parts.
44 Special Application (Punch In/Out Recording) 1 2 -B T rack 1 T rack 2 T rack 3 T rack 4 This part is changed. Playback start point EQ EQ 2 -H 2 -F 2 -G 2 -A 2 -C 2 -D 2 -E When you finish storing and adjusting the edit points, you can proceed to the Auto Punch In/Out operation.
45 Special Application (Punch In/Out Recording) Locate Locate Stop here. Auto Punch In point Auto Punch Out point The FD-4 stops at a point that precedes the Auto Punch In point by the specified preroll time. (0~10 seconds) Auto Punch In point Auto Punch Out point AUTO RTN ST ART point AUTO RTN END point Rehearsal area 5.
46 Special Application (Punch In/Out Recording) 2 1 3 EQ EQ 3 3 3 3 3 3 3 Undo/Redo Auto Punch In/Out recording You can undo or redo Auto Punch In/Out recording. Press the UNDO/REDO key after recording is complete to restore the conditions that existed prior to the recording.
47 Special Application (Punch In/Out Recording) T rack 1 T rack 2 T rack 3 T rack 4 This part is changed. Playback start point Playback end point Punch In point (Rehearsal in) Punch Out point (Rehearsal out) All tracks are in playback monitoring mode.
48 Special Application (Punch In/Out Recording) 4. Press the STOP button. 5. Play track 3 and check the result of Punch In/Out. <Caution after Punch Out> At “T ake” of punch out, the punch-i.
49 Special Application (Ping Pong Recording) TRK 4 TRK 3 TRK 2 TRK 1 Sound source A TRK 4 TRK 3 TRK 2 TRK 1 TRK 4 TRK 3 TRK 2 TRK 1 TRK 4 TRK 3 TRK 2 TRK 1 TRK 4 TRK 3 TRK 2 TRK 1 TRK 4 TRK 3 TRK 2 TR.
50 Special Application (Ping Pong Recording) 1 1.Turn the AUX knob of the channel signal to which you wish to apply effects toward AUX 1. Use the AUX R TN 1 knob to adjust the return signal level. At this time, make sure that the [OL] section of level meters 4 and R do not light up continuously.
51 Special Application (Ping Pong Recording) TRK 4 TRK 3 TRK 2 TRK 1 ADD. TRK L ADD. TRK R Sound source D This chapter explains how to perform ping-pong recording using Additional tracks L and R. In this example session, we ping-pong record tracks 1–4 to the Additional tracks.
52 Special Application (Digital Recording) INPUT 3 R MON OUT L R ST OUT L AUX RTN 1 R MONO/L AUX RTN 2 R MONO/L 2 AUX SEND 1 4 INSERT 3 INPUT 4 SCSI OUT IN DATA R RECORDER IN L IN MIDI OUT PUNCH IN/OU.
53 Special Application (Digital Recording) INPUT 3 R MON OUT L R ST OUT L AUX RTN 1 R MONO/L AUX RTN 2 R MONO/L 2 AUX SEND 1 4 INSERT 3 INPUT 4 SCSI OUT IN DATA R RECORDER IN L IN MIDI OUT PUNCH IN/OU.
54 Special Application (Digital Recording) 1 2 3 4, 8 6, 13 7 7 9 10 11 5, 12 14 DA T Effect unit 1 Effect unit 2 EQ EQ Digital mixdown As described in the previous section, you may mix down digital s.
55 Å@Special Application (How to use the RECORDER IN jack) How to use the RECORDER IN jack INPUT 3 R MON OUT L R ST OUT L AUX RTN 1 R MONO/L AUX RTN 2 R MONO/L 2 AUX SEND 1 4 INSERT 3 INPUT 4 SCSI OU.
Editing T racks 56 CLIPBOARD IN point CLIPBOARD OUT point AUTO PUNCH IN point Copy Clip Paste Copy source track Paste destination track CLIPBOARD IN point CLIPBOARD OUT point AUTO PUNCH IN point Move .
Editing T racks 57 DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI DRIVE AUTO A.
Editing T racks 58 AUTO PUNCH IN point Any track Any track AUTO PUNCH OUT point Erase ABS 0 REC END Silence AUTO PUNCH IN point Any track Any track AUTO PUNCH OUT point Erase ABS 0 REC END Silence ABS 0 Additional track Real track Real track REC END Additional track REC END 7.
Editing T racks 59 ABS 0 Real track AUTO PUNCH IN point AUTO PUNCH OUT point (REC END) ABS 0 Real track REC END AUTO PUNCH IN point AUTO PUNCH OUT point (REC END) ABS 0 Real track ABS 0 Real track REC END REC END 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 DRIVE AUTO A.
Editing T racks 60 Real track 4 Real track 1 Real track 2 Real track 3 data on Real track 2 Real track 1 data on Real track 4 Real track 3 data on Real track 4 data on Real track 3 <After swap> .
Editing T racks 61 DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI Executing Track Exchange 1. While the FD-4 is stopped, press the EDIT key repeatedly until [TRK Exchg] flashes on the display .
62 Cue & Review Function 2 1 3 <Display of 16-times review> <Display of 32-times cue> EQ EQ ABS PGM S MF DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI ABS PGM S MF DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI ABS PGM S MF DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI ABS PGM S MF DRIVE AUTO A.
Storing a Locate Point (Edit Point) 63 1 4 2 3 EQ EQ You can store time information (time or bar/beat/clock) in each memory key. The stored time information will be used to locate a point in data in the recorder section, or as an edit point to perform the Auto Punch In/Out, Copy & Paste, Move & Paste, or Erase function.
Storing a Locate Point (Edit Point) 64 2 4 1, 2 3 2 1, 4 2 3 2 EQ EQ EQ EQ Editing and storing locate data If you know the position of the desired locate point, follow the steps below. 1. Press the HOLD/> key while the FD-4 is stopped. The currently-displayed time value (or bar/beat/clock value) is captured and the FD-4 enters data edit mode.
Storing a Locate Point (Edit Point) 65 2 4 2 2 1 3 EQ EQ Editing the data stored in the LOCA TE key You can recall the last located point and edit the value. You can use the edited value to locate the point later or store it to another memory key. 1. Press the SHIFT and LOCA TE keys simultaneously while the FD-4 is stopped.
Locate Function 66 2 1 Locate Locate Playback AUTO PUNCH IN point (Example) Locating the AUTO PUNCH IN point 3 EQ EQ PLA Y AUTO The FD-4 locates the desired edit point immediately (that is, it moves the current position of the data in the recorder section).
Locate Function 67 1 2 3 Locate Playback AUTO RTN ST ART point AUTO RTN END point Stop <Auto Return operation> RTN AUTO EQ EQ 3. Press the LOCA TE key.
Locate Function 68 PLA Y RTN AUTO Locate Playback AUTO RTN ST ART point AUTO RTN END point AUTO PUNCH IN point AUTO PUNCH OUT point Rehearsal range 1 2 3 Locate Playback AUTO RTN ST ART point AUTO RTN.
Preview Function 69 1 1 2 Approx. 2 sec. Approx, 1 sec. (mute playback) Approx, 1 sec. (normal playback) The sound rises at the memory point. Operation Memory key EQ EQ ABS LOC S M H F SF DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI ABS LOC S M H F SF DRIVE AUTO A.
Preview Function 70 1 1 2, 4 3 3 5 HOLD/> key or F FWD button Time Base ABS or MTC BAR/BEA T/CLK SF -> H -> M -> S -> F SF <- H <- M <- S <- F CLK -> BAR -> CLK <- BAR <- Flashing EQ EQ ABS LOC S M H F SF DRIVE AUTO A.
MIDI Synchronization 71 INPUT 3 S T OUT L AUX RTN 1 R MONO/L AUX RTN 2 R MONO/L 2 AUX SEND 1 4 INSERT 3 INPUT 4 SCSI OUT IN DATA R RECORDER IN L IN MIDI OUT PUNCH IN/OUT DATA MIDI Effect unit 1 Effect.
MIDI Synchronization 72 INPUT 3 S T OUT L AUX RTN 1 R MONO/L AUX RTN 2 R MONO/L 2 AUX SEND 1 4 INSERT 3 INPUT 4 SCSI OUT IN DATA R RECORDER IN L IN MIDI OUT PUNCH IN/OUT DATA MIDI INPUT 3 R MON OUT L .
MIDI Synchronization 73 Operation on the FD-4 Output MMC command (Device No. = 7F fixed) PLA Y + RECORD buttons Punch In operation in T AKE mode of Auto Punch In/Out. Punch In operation via a footswitch. RECORD button ON/OFF . Rehearsal In in rehearsal mode of Auto Punch In/Out.
MIDI Synchronization 74 INPUT 3 AUX RTN 1 R MONO/L AUX RTN 2 R MONO/L 2 AUX SEND 1 4 INSERT 3 INPUT 4 SCSI OUT IN DATA R RECORDER IN L IN MIDI OUT PUNCH IN/OUT DATA MIDI MTC with Sequence Software Sync system in Slave mode You can set up the system in which the FD-4 in Slave mode synchronizes to an external master MIDI device.
MIDI Synchronization 75 • If the FD-4 does not chase and lock correctly , check the connecting cables and settings. Recording You can record data on the FD-4 while the FD-4 is chasing and locking to the sequence software signals.
76 Saving and Loading Song Data Saving from FD-4 to DA T Loading from DA T to FD-4 OPTICAL IN OPTICAL OUT DA T A OUT DA T A IN EQ EQ Outline of the save/load operation The FD-4 enables you to save the recorded song data (in- cluding SETUP data) to a connected DAT machine and load the saved data as is from DAT to the SCSI disk in the FD-4.
77 Saving and Loading Song Data 1 2, 5 3, 4, 6, 7 8 Data recorded on a disk in Normal mode Save FD-4 DA T Record mode: 32kHz/SP mode Load Disk in Mastering 1 or Mas- tering 2 EQ EQ SETUP DRIVE AUTO A.
78 Saving and Loading Song Data SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI PGM SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI ? SURE SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI REMAIN S M H 2.
79 Saving and Loading Song Data 1 2, 5 3, 4, 6, 7 8 EQ EQ SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI PGM SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI Loading song data You can load the data from DAT to the SCSI disk of the FD-4.
80 Saving and Loading Song Data SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI DIGIT AL SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI REMAIN S M H DIGIT AL 7. Press the EXECUTE/YES key again. [Play DAT !] appears on the display. 8. Start playing the DA T machine.
81 Changing the Initial setting (SETUP mode) Sign. Set ? menu T empo Set ? menu Title Edit ? menu Del PGM ? menu Click ? menu Preroll ? menu Sync Out? menu Frame Rate ? menu Mtc Offset ? menu Ofset Mode ? menu Slave Mode? menu Slave T ype? menu Rec Protect ? menu Digi.
82 Changing the Initial setting (SETUP mode) SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI BAR SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI BAR Setting a time signature Using the “Setting a time signature” menu, you can set a time signature of a given measure on the internal program- mable Tempo Map.
83 Changing the Initial setting (SETUP mode) 2. Rotate the JOG dial clockwise. You can view the current tempo values in sequence. Tempo value [- - - BAR - TEMPO - - -] means that no tempo values are specified after the current setting. With the initial setting, [001 BAR 1 TEMPO 120] is followed by [- - - BAR - TEMPO - - -].
84 Changing the Initial setting (SETUP mode) Tempo Map Time signature setting Tempo setting 001 BAR 4 4 005 BAR 3 4 001 BAR 1 TEMPO 120 003 BAR 1 TEMPO 90 005 BAR 3 TEMPO 60 007 BAR 2 TEMPO 120 4 4 3 4 T empo=120 T empo=90 T empo=60 T empo=120 4.
85 Changing the Initial setting (SETUP mode) SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI S SETUP DRIVE AUTO A.
86 Changing the Initial setting (SETUP mode) SYNC OUT CLK SYNC OUT MTC SYNC OUT SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI Setting MIDI sync output signal Th.
87 Changing the Initial setting (SETUP mode) SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI F SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI F MTC OFFSET SETUP DRIVE AUTO A.
88 Changing the Initial setting (SETUP mode) SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI ABS S M HF SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI ABS S M HF SETUP DRIVE AUTO A.
89 Changing the Initial setting (SETUP mode) SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI SLA VE SETUP DRIVE AUTO A.
90 Changing the Initial setting (SETUP mode) SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI <Note> • Y ou need to input MTC from an external device to the FD-4 with any Slave type (external sync signal). • The FD-4 re-chase window is fixed to ten frames.
91 Changing the Initial setting (SETUP mode) SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI Setting digital input tracks The “Setting digital input tracks” menu allows you to as- sign digital signals input at the DATA IN connector of the FD-4 to the tracks.
92 Changing the Initial setting (SETUP mode) SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI Setting digital output tracks The “Setting digital output tracks” menu enables you to assign the track that outputs digital signals from the DATA OUT connector of the FD-4 to an external digital device.
93 Changing the Initial setting (SETUP mode) SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI SETUP DRIVE AUTO A.PUNCH SYNC OUT CLK SCSI 3. Use the JOG dial to turn the mode on or off.
94 MIDI Implementation Chart/MMC List/Maintenance/Specifications Basic Channel Function..................... Default Changed Transmitted Recognized Remarks Mode Default Message Altered Note Number: Tr.
95 MIDI Implementation Chart/MMC List/Maintenance/Specifications MMC Command List Command List Movement (Recorder) 01: STOP STOP 02: PLAY PLAY 03: DEFERRED PLAY DEFERRED PLAY 04: FAST FORWARD F FWD 05.
96 MIDI Implementation Chart/MMC List/Maintenance/Specifications Maintenance Specifications Cleaning the exterior * For normal cleaning, use a soft dry cloth For stubborn dirt, moisten a cloth in diluted detergent, wring it out firmly, and wipe the dirt off.
97 MIDI Implementation Chart/MMC List/Maintenance/Specifications Block Diagram Mastering Mode 1 : 4 Real track + 2 Additional track (Sampling Rate: 44.1kHz/ 16-bit linear) Mastering Mode 2 : 4 Real track (Sampling Rate: 44.1kHz/16-bit linear) <Digital Input/Output> * 32kHz/16-bit linear (Normal mode) , Corresponds to DAT 32kHz/SP mode.
<AUSTRIA> NAME: ATEC Audio-u. Videogeraete VertriebsgesmbH. ADD: Im Winkel 5, A-2325 Velm, Austria TEL: (+43) 2234-74004, FAX: (+43) 2234-74074 <BELGIUM> NAME: EML N.
INDEX [A] ABS time......................................24 Additional track...................26, 30 Analog recording......................28 Auto punch in/out....................43 Auto play....................................66 Auto return..........
C PRINTED IN JAP AN APR. 1998 8288 414 100 FX FOSTEX CORPORA TION 3-2-35, Musashino, Akishima-shi, T okyo, Japan 196 -0021 FOSTEX CORPORA TION OF AMERICA 15431, Blackburn A ve.
An important point after buying a device Fostex FD-4 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fostex FD-4 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fostex FD-4 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fostex FD-4 you will learn all the available features of the product, as well as information on its operation. The information that you get Fostex FD-4 will certainly help you make a decision on the purchase.
If you already are a holder of Fostex FD-4, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fostex FD-4.
However, one of the most important roles played by the user manual is to help in solving problems with Fostex FD-4. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fostex FD-4 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
