Instruction/ maintenance manual of the product VU155N Series Follett
Go to page of 20
F ollowing installation , please forw ar d this manual to the appropriat e operations per son . Installation, Oper ation and Ser vice Manual VU155N Ser ies Ice and W at er Dispenser s Order parts online www.
Welcome to Follett Corporation Important cautions Specifications Installation Installing dispenser in counter Field wiring diagrams Installing optional icemaker Operation How the dispenser works Clean.
We lcome to F ollet t Follett ice dispensers enjoy a well-deserved reputation for excellent performance, long-term reliability and outstanding after-the-sale support. To ensure that this dispenser delivers that same degree of service, we ask that you take a moment to review this manual before beginning the installation of the dispenser.
Specif ications Electrical Each icemaker and dispenser require a separate circuit with with electrical disconnect within 10 ft (6m). Equipment ground required. Standard electrical – 115V, 60Hz, 1 phase. Maximum dispenser fuse – 15 amps, Maximum icemaker fuse – 20 amps each.
Dimensions and c learances Required clearances 51" (1295mm) minimum above counter for installation if dispenser will be dropped into counter 36" (915mm) minimum above counter for all units a.
Installation Installing dispenser in counter Note: All dispensers must be supported from below with supplied 6" – 9" (153 – 229mm) adjustable leg accessory, or equivalent. Do not hang dispenser on flange. All dispensers must be installed level in both directions to ensure proper operation.
F ield wiring diagr ams Note: Field wiring diagrams are intended to aid electricians or technicians in understanding how equipment works. All field wiring must be installed in accordance with all local and NEC codes.
Oper ation How the dispenser w or ks Follett’s dispensers are available in automatic load configurations, fed from one or two Follett remote icemakers or manual load configurations (using ice from another source). In all models, ice is stored below the counter in the dispenser storage area.
Recommended cleaning prior to start up Cleaning ice storage area before use 1. Refer to disassembly instructions (see Service section) and remove dispense wheel from ice storage area. 2. Remove auger, auger tube and dispense mechanism. 3. Wipe all components and ice storage area with cleaning Solution A.
Dispense chut e cov er r emov al 1. Remove top cover. 2. Push chute cover up vertically to slip off holding tab. 3. After clearing tab, pull chute cover forward to remove. Dispense mechanism assembl y r emov al 1. Remove top cover. 2. Remove chute cover (see above).
wheel motor baffle plate wheel motor mounting plate dispense wheel auger tube auger auger motor (side view) auger bearing plate stationary agitator rotating agitator Front View plain water hook-up chilled water coil Fig.
Wi r ing diagr ams PL3-1 6 9 AU TO FILL 2 Red 6 Red Red Red Blk Brn Ye l Red 24V JUNCTIO N BO X ICEM AKER #2 BIN SIGNAL (24V) 5 SEC O N 18 M IN O FF Au to F ill Tim er Blu Blu 3 2 ICEM AKER #1 BIN SIG.
Symptom Ice does not dispense. • Auger motor does not run • Wheel motor does not run Ice does not dispense. • Auger motor runs • Wheel motor runs • Gate does not open Ice does not dispense. • Auger motor does not run • Wheel motor runs Ice does not dispense.
Reference # Description Part # 1 Label, “Follett” 502438 2 Top cover (includes label) 502606 3 Drain pan 502446 4 Grille, drain pan 502450 5 Cover, electrical components 502593 6 Lid, rear access .
Dispense assembly Side View (RH unit shown) Reference # Description Part # 1 Gate, dispense 502455 2 Linkage pin, gate/solenoid 502456 3 Pin, quick release, 5.
Reference # Description Part # 1 Auger, LH unit (black, stamped with “1”) 502491 Not shown Auger, RH unit (gray, stamped with “2”) 502492 2 Plate, auger bearing 501696 Not shown Tube, auger, r.
Reference # Description Part # Auger motor/drive assembly, vertical (includes all items below) 502493 1 Motor, vertical auger (includes gearbox and capacitor) 502476 2 Chain, auger drive #35, 40p 5024.
Reference # Description Part # 1T ransformer, 24V 502058 2 Relay, dispense 501826 3 Relay, auto fill 501826 4 Timer, auto fill (automatic fill units) 502471 5S trip, terminal 502472 6 Tube, water disp.
19.
00119602R00 04/04 801 Church Lane • PO Box D, Easton, PA 18044, USA Toll free (800) 523-9361 • (888) 2-FOLLETT (610) 252-7301 • Fax (610) 250-0696 • www.
An important point after buying a device Follett VU155N Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Follett VU155N Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Follett VU155N Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Follett VU155N Series you will learn all the available features of the product, as well as information on its operation. The information that you get Follett VU155N Series will certainly help you make a decision on the purchase.
If you already are a holder of Follett VU155N Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Follett VU155N Series.
However, one of the most important roles played by the user manual is to help in solving problems with Follett VU155N Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Follett VU155N Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
