Instruction/ maintenance manual of the product MM39/44/49VF FMI
Go to page of 20
Instructions Models MM39/44/49VF Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other appliance. WHA T TO DO IF YOU SMELL GAS: Do not try to light any appliance. • Do not touch any electrical switch; do • not use any phone in your building.
FireplacePartsDiagram......................................................................................... Pg.2 FireplacePartsList................................................................................................
2 Fireplace Parts Diagram Figure 1 Exploded Diagram 5 9 12 2 7 1 3A 2X 2X 3X 7X 2X 8X 3 6 11 W ARNING Failure to position the parts in accordance with these diagrams or failure to use only parts specically approved with this appliance may result in property damage or personal injury .
3 Optional Outside Ø4” Combustion Air Kit Model No.: MM4AK (Ø4” Ducting not included) Refractory Firebrick Liners (HerringbonePatternshown,alsoavailable inRunningBond-seePg.
4 General Information Introduction WeextendawarmwelcomefromallofusatFMI PRODUCTS,LLCproudmanufacturersoftheGrandMeridian Fireplaces.
5 Safety Information Carbon Monoxide Poisoning: Early signs of carbon monoxide poisoning resemble the u, with headaches, dizziness, or nausea. If you have these signs, the replace may not be working properly .
6 Location Note: Y ou may need to provide combustion and ventilation air from an outside source to adequately satisfy local codes so avoid.
7 For conventional framing, where the oor joists are parallel with the sides of the rebox, the addition of oor joists to align with the anchor brackets allows the brackets to be directly connectedtotheoorjoists.
8 Grand Meridian W eight Determinations ThefollowingaredeadloadweightestimatesfortheGrandMeridianFireplace. T able I FireplaceModel MM39VF MM44VF MM49VF FireplaceWeight 809lbs. 896lbs. 987lbs. Mortar ,Rebar& ReadyMixConcrete 350lbs.
9 Clearances The Importance of Clearances W arning to the structural engineer and/or building contractor: It is your responsibility to be certain that t.
10 Interior W all Materials: W all materials, such as drywall, should be set ush with the rough front face of the V ent-Free replace.
11 Unconned Space An unconned space has a minimum total air volume of 50 cu.ft. (cubic feet) for each 1,000 Btu/Hr input rating of all appliances in the total space (cu.
12 Important Pre-installation Information Overview Y ou will nd that the Grand Meridian Fireplace is designed for completeassembly at yourconstruction sitewith allnecessary items delivered consistingof interlocking precast parts, 50 lbs.
13 Fireplace Assembly Procedures TOOLS NEEDED FOR INST ALLA TION: One4ft.level • Roto-hammerwith½”drillbit • DrillmotorwithmixerbladetomixMortar .
14 Figure 21 Combustion Air Access RightorLeft(Rightshown). Apply mortar Applymortar SideW all RearW all SideW all When you have arranged all the .
15 Raised and Flush Hearth Application: If you would prefer to have a raised hearth, the V ent-Free box can be raised to the desired height using wood studs or concrete blocks.
16 Firebrick Liner Installation It is required that the interior sides, rear and bottom be lined with minimum 1-1/8” thick rebrick. Pre-fabricated re brick liner wallscanmaketheinstallationeasier .
17 Appendi xI For installations regulated by the International Residential Code, the support foundation for the fireplace installed on concrete shal l consist of am inimum o f6i nche st hick reinforced concrete slab. The minimum specified compressive strength of f’ c ,s hall be as required in Table R402.
18 Appendi x I I FIGURE R301.2(3) WEATHERING PROBABILITY MA P F OR CONCRETE a. Alask a a nd Hawaii are classified as severe and negligible, respectively. b. Lines defining areas are approximate only. Local conditions may be more or less severe than indicated by region classification.
WARRANTY KEEP THIS WARRANTY FMI PRODUCTS, LL C LIMITED WARRANTIES New Products FMIPRODUCTS, LLCwarrants allGrandMeridian Fireplacesto befree fromdefectsin mat.
An important point after buying a device FMI MM39/44/49VF (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought FMI MM39/44/49VF yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data FMI MM39/44/49VF - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, FMI MM39/44/49VF you will learn all the available features of the product, as well as information on its operation. The information that you get FMI MM39/44/49VF will certainly help you make a decision on the purchase.
If you already are a holder of FMI MM39/44/49VF, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime FMI MM39/44/49VF.
However, one of the most important roles played by the user manual is to help in solving problems with FMI MM39/44/49VF. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device FMI MM39/44/49VF along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
