Instruction/ maintenance manual of the product pmn Fluke
Go to page of 25
405 ESSEX ROAD, NEPTUNE, NJ 07753 TEL: (732) 922-9300 FAX: (732) 922-9334 INSTRUCT ION MANUAL FOR .
Table of Contents 4 - 1 4.1 Remote Control 4 - 1 4 OPERA T ION 3 - 4 3.6.4 For Units with O/P Voltage > 6KV: 3 - 4 3.6.3 For Units with O/P Voltage £6KV 3 - 4 3.6.2 Output Gr ound Connection 3 - 3 3.6.1 Grounding of Input Line 3 - 3 3.6 Grounding the Product 3 - 3 3.
6 - 1 6.3 Calibration 6 - 1 6.2 Main tenance 6 - 1 6.1 Safety Precautions 6 - 1 6 MA INTEN A NCE A ND CA LIBRA TION 5 - 5 5.7 Long Charge T ime W ith Power Factor Corrected (PFC) Units 5 - 4 5.6 Continuous HV DC Operation (Constant Voltage) 5 - 4 5.5 Determining AC Line Current 5 - 3 5.
.
.
" " " " Input Voltage selective by Terminal Block position *Note: In p ut cur rent ratin gs given are m axi mu m wh en out put Repeti tion Ra te is =>10Hz.
90%, non-condensing .
2.23.4 SUFFIX -EN "Low Enable" - A +10 to 15 volt (high) si gnal will disable power supply operation. A 0 to +1.5 volt (low) signal will enable t he supply. 2.23.5 SUFFIX -5V 0 to +5 volt voltage (0 to full-scale output) programming 2.23.6 SUFFIX -LP Latching overload pr otection.
Figure 2-1 Mechanical Dimensions for 500A, 102A, 152A Outputs up to 6KV (for grounding instruct ions see SECTION 3.6) 83-493-001 Revision G 2 - 5 Specifications.
Figure 2-2 Mechanical Dimensions for 500A, 102A, 152A Outputs from 7KV t o 40K V (for grounding instruct ions see SECTION 3.6) 83-493-001 Revision G 2 - 6 Specifications.
Figure 2-3 Mechanical Dimensions for 202A Outputs up to 6KV (for grounding instruct ions see SECTION 3.6) 83-493-001 Revision G 2 - 7 Specifications.
Figure 2-4 Mechanical Dimensions for 202A Outputs from 7KV t o 40K V (for grounding instruct ions see SECTION 3.6) 83-493-001 Revision G 2 - 8 Specifications.
.
The PFC version connection i s shown in Figure 3-2. Connect t he input voltage line wires to L2 and COM terminals. WA RNING: 152A a nd 202A PFC M odels are only av ailable w ith 220 VA C Nominal.
.
3.6.1 GROUNDING OF I NPUT LINE The supply is grounded through the ground terminal of the input conne ctor. A protective ground connection by the way of the grounding conductor in the input te rminal is essential for safe operat ion.
.
Figure 4-1 Eample Of Interface Connection 83-493-001 Revisi on G 4 - 2 Operations.
& &am.
For clarif ication and fur ther technic al assist ance speci fic to your applicat ion, please cont act Lambda EMI .
Figure 5.2 Output Current Measurement A series terminating resis tor (or series i nductor or cla mp diode) m us t be added as shown if the average value of the peak current exceeds 110% of the normal output curr ent.
.
Figure 5.3 HV Bias Measurements .
! ! ! ! .
.
An important point after buying a device Fluke pmn (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fluke pmn yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fluke pmn - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fluke pmn you will learn all the available features of the product, as well as information on its operation. The information that you get Fluke pmn will certainly help you make a decision on the purchase.
If you already are a holder of Fluke pmn, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fluke pmn.
However, one of the most important roles played by the user manual is to help in solving problems with Fluke pmn. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fluke pmn along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
