Instruction/ maintenance manual of the product T1456 Fisher-Price
Go to page of 24
T1456 www .fi sher -price.com.
2 W ARNING A VER TISSEMENT ADVER TENCIA CAUTION MISE EN GARDE PRECAUCIÓN • This pac kage cont ains small par ts in its unassemb led stat e. Adult assemb l y is r equired. • Le pr oduit non assemblé compr end de petits éléments détachab les susceptib les d’êtr e av alés.
3 Consumer Information Renseignements pour les consommateurs Información para el consumidor • Please read these instructions before use of this swing. Keep this instruction sheet for future reference, as it contains important information. • Adult assembly is required.
4 Motor Assembly Boîtier du moteur Unidad del motor Pad Housse Almohadilla 2 Lower Legs (Left and Right) 2 pieds (gauche et droit) 2 patas inferiores (izquierda y derecha) Seat Back T ube T ube du dossier T ubo del respaldo Seat Bottom Siège Asiento Body Support Support pour bébé Soporte corporal AC Adaptor Adaptateur c.
5 Fasteners Pièces de fixation Sujetadores Do not over -tighten the screws or the bolt. Ne pas trop serrer les vis ou le boulon. No apretar en exceso los tornillos ni el perno.
6 Assembly Assemblage Montaje 1 2 While pressing the buttons on the motor assembly tubes, fit it • onto the straight end of each upper leg. Hint: Y ou may need the help of another adult. T out en appuyant sur les boutons situés sur les tubes du boîtier • du moteur , insérer ceux-ci dans les extrémités supérieures des pattes.
7 Assembly Assemblage Montaje Pull apart the legs. • Lift the free end of the frame support bar . • Fit the hole in the frame support bar over the peg on the • opposite leg. Push to "snap" the frame support bar in place. Écarter les pattes de la structure.
8 Assembly Assemblage Montaje T urn the seat bottom face down. • Insert four #8 x • 3 / 4 " (1,9 cm) screws into the holes in the seat and tighten with a Phillips screwdriver . T urn the assembly upright. • Placer le siège à l'envers.
9 Assembly Assemblage Montaje 8 • T urn the seat face down. • Fit the frame tube connector to the pegs on the seat bottom. • Insert four #8 x ¾ " (1,9 cm) screws into the frame tube connector and tighten with a Phillips screwdriver . • Placer le siège à l'envers.
10 • First, fit an M5 lock nut into a hole in the motor assembly tube. Make sure the rounded side of the lock nut faces out. • Next, insert an M5 x 36 mm bolt through the opposite hole in the motor assembly tube. • While holding the lock nut in place, tighten the bolt with the Allen wrench.
11 Assembly Assemblage Montaje 11 Pad Housse Almohadilla Fit the upper pocket on the back of the pad over the seat back tube. • Glisser le rabat supérieur , situé au dos de la housse, sur le tube • du dossier . Ajustar la funda superior del dorso de la almohadilla sobre el tubo • del respaldo.
12 Assembly Assemblage Montaje Fit the elastic loops on the pad down through the holes on • the seat bottom. Insérer les boucles élastiques de la housse dans les trous du siège. • Ajustar los ganchos elásticos de la almohadilla en los orificios • del asiento.
13 Assembly Assemblage Montaje Place the body support onto the pad. • Pull the waist belts through the slots in the body support. • Mettre le support pour bébé sur la housse. • Faire passer les courroies abdominales dans les fentes du support.
14 • Loosen the screws in the batter y compartment door with a Phillips screwdriver and remove the battery compartment door . • Insert four “D” (LR20) alkaline batteries into the batter y compartment. • Replace the battery compartment door and tighten the screws.
15 W ARNING A VER TISSEMENT ADVER TENCIA T o pr ev ent serious injury or death fr om falls and being strangled in the r estraint s y stem: • Al wa ys use r estraint s yst em. • Ne v er use with an activ e child who ma y be able t o climb out of the product.
16 Securing Y our Child • Place your child in the seat. • Fasten the waist straps to the crotch strap. Make sure you hear a “click” on both sides. • Check to be sure the restraint system is securely attached by pulling it away from your child.
17 Free End Extrémité libre Extremo libre Anchored End Extrémité fixe Extremo fijo LOOSEN DESSERRER AFLOJAR Swinging Direction • T urn the seat until it locks into place to select a swinging direction. Sens du balancement • Faire pivoter le siège jusqu'à ce qu'il se verrouille avant de choisir le balancement souhaité.
18 AC Power Use • Place the swing near a standard wall outlet. • Plug the AC adaptor into the power cord extending from the back of a leg. • Plug the AC adaptor into the wall outlet. • Use the AC adaptor only in a wall outlet. Do not plug the adaptor into a ceiling outlet.
19 Swing • Slide the power switch to turn power ON. The power L.E.D. will turn on. • Press the swing speed buttons and to adjust to any of six swing speeds. Look at the L.E.D.'s below the buttons to see the speed you selected. • Slide the power switch to turn power OFF .
20 Columpio • Mover el interruptor de encendido para activar la unidad. Se iluminará la luz L.E.D. de encendido. • Presionar los botones de velocidad del columpio y para ajustar la velocidad en uno de seis movimientos. Observar las luces L.E.D. abajo de los botones para ver la velocidad seleccionada.
21 Care Entretien Mantenimiento T o remove the pad: • Remove the elastic loops from the pegs and the pad clips on the seat bottom. • Pull the restraints down through the slots in the pad. • Lift the pad off the seat. T o replace the pad, follow the assembly instructions.
22 Storage Rangement Almacenamiento • Push the tab on the frame support to release it. • Appuyer sur la languette de la barre de soutien pour la dégager . • Empujar la lengüeta del soporte del armazón para soltarla. • Pull the end of the frame support bar off the leg and lower it.
23 Consumer Information Renseignements pour les consommateurs Información para el consumidor FCC Statement (United States Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. ©2009 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. Fisher Price, Inc., une filiale de Mattel, Inc., East Aurora, NY 14052 É.-U. ©2009 Mattel, Inc.
An important point after buying a device Fisher-Price T1456 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fisher-Price T1456 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fisher-Price T1456 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fisher-Price T1456 you will learn all the available features of the product, as well as information on its operation. The information that you get Fisher-Price T1456 will certainly help you make a decision on the purchase.
If you already are a holder of Fisher-Price T1456, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fisher-Price T1456.
However, one of the most important roles played by the user manual is to help in solving problems with Fisher-Price T1456. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fisher-Price T1456 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
