Instruction/ maintenance manual of the product H4790 Fisher-Price
Go to page of 16
1 Instructions Model Number: H4790 Please read these instructions befor e assembly and use of this product. Adult assembly is requir ed. Tool needed for assembly: Phillips Scr ewdriver (not included). Product features and decor ations may vary from photo above.
W ARNING This product contains small par ts in its unassemb led state. Adult assemb ly is required. Prevent serious injury or death fr om falls or sliding out: • The child should at all times wear a saf ety har ness correctly fitted and adjusted. The tra y is not designed to hold the child in the chair .
3 3 Parts Pa d 3 Food Tr ays 2 To ys (Toy s may be different) Seat Back Seat Bottom Frame Hinge Rod 2 Seat Bottom Tubes 4 Screw Retainer s Base Tr ay Frame Footrest Headrest Basket Stor age Caddy Front Base Back Base #1 0 x 2.2 cm Black Screw #1 0 x 2.
4 2 • Slide a seat bottom tube thr ough each set of plastic rings on the seat bottom. 1 • Place the seat bottom face down on a flat surface. • At an angle, fit the footr est on the seat bottom, as shown.
5 5 Assembly 4 Insert Scr ews Her e Footrest • Insert two #1 0 x 2.2 cm black screws thr ough the footrest and into the seat bottom. Tighten the screws. #1 0 x 2.2 cm Black Screw - 2 5 • T urn the seat bottom assembly upright. • Fit the seat back pins into the openings in the top side of the seat bottom assembly .
6 6 6 Assembly 8 • Identify the back and fr ont base. The front base has tapered leg tubes. Y ou will use the back base for the next assembly step. Taper ed Leg Tube Back Base Front Base 9 Screw Retainer - 2 #1 0 x 2.2 cm Black Screw - 2 • P osition a frame so that the decorated side is outwar d.
7 7 7 Assembly 12 Front Leg Holes Screw Retainer - 2 #10 x 2.2 cm Black Scr ew - 2 • Insert the fr ame front legs onto the front base. • Fit a scr ew retainer over a hole in the front leg. • Insert a #1 0 x 7 / 8 " (2.2 cm) black scr ew through the scr ew retainer and fr ont leg.
8 8 8 Assembly Back and Bottom View Seat Bottom Tube Ends 14 Seat Height Adjuster s • Fr om the back and bottom of the assembly , insert a #8 x 1.9 cm screw thr ough both seat height adjusters and the ends of the seat bottom tube. Tighten the screws.
9 Assembly Shoulder P ortion 16 • Insert the cr otch belt through the slot in the pad. Make sure the crotch belt is not twisted. • Fold the top of the pad down. • Remove the shoulder portion of the waist/shoulder belts by feeding them through the slots in the seat back.
10 Assembly • Fit the str ap on the top of the headrest through the handle. • Fit the pad str ap through the handle and press it to the s mall fastener on the back of the seat. • Fit the headr est strap through the handle and pr ess it to the large fastener on the back of the seat.
11 11 Securing Y our Child IMPORTANT! Before each use, inspect this pr oduct for damaged hardwar e, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or br oken. Contact Mattel for replace- ment parts and instructions if needed.
12 12 Securing Y our Child 4 • To tighten the s houlder belts: Hold the adjuster and pull the front shoulder str ap down. • To loosen the s houlder belts: Slide the adjuster down. Note: After adjusting the restr aint system to fit your child, make sure you pull on it to be sur e it is securely fastened.
13 Prevent serious injury or death fr om falls or sliding out. The child should at all times wear a saf ety har ness correctly fitted and adjusted. The tra y is not designed to hold the child in the chair . W ARNING 7 • Fit the base tr ay onto the seat armrests.
14 11 Release Bar Base Tr ay • While pushing the r elease bar on the front of the base tray , pull the tray base towar ds you and remove. Base Tr ay 12 • Fit the food tr ay into the base tray , as shown. Hint: Before use, thorougly wash all parts (the trays) that may contact food.
15 Adjusting the Seat Prevent serious injury or death fr om falls or sliding out. It is recommended that the high chair be used in the upright position only b y children capable of sitting upright unassisted.
Storage 16 Base Tr ay • Fit the holes on the base tr ay latches onto the pegs on the back of the high chair frame. Pe g Hole 17 Pull Frame Release Latch • With the legs all the way open, lower the seat to position 7 the lowest position). • Pull the fr ame release latches forward and push the r ear legs toward the fr ont legs.
An important point after buying a device Fisher-Price H4790 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fisher-Price H4790 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fisher-Price H4790 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fisher-Price H4790 you will learn all the available features of the product, as well as information on its operation. The information that you get Fisher-Price H4790 will certainly help you make a decision on the purchase.
If you already are a holder of Fisher-Price H4790, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fisher-Price H4790.
However, one of the most important roles played by the user manual is to help in solving problems with Fisher-Price H4790. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fisher-Price H4790 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
