Instruction/ maintenance manual of the product XLT-30 Fisher
Go to page of 12
XLT-30 Operating Manual Acoustical Leak Detector FISHER RESEARCH LABORATORY.
CONTENTS Introduction ........................................................................... pg. 1 Instrument Set ....................................................................... pg. 2 Faceplate & Control Panel ........................
INTRODUCTION Fisher Research Laboratory has always been a leader in the field of acoustical leak detection. From the early LT-10 through the XLT-20, high quality sound amplification has been synonymous with the name Fisher. Fishers XLT-30 takes leak detection to a new level.
2 INSTRUMENT SET 1. Control Box All listening and filtering controls for the XLT-30 are contained in this sturdy housing. The function of each control is described in the section entitled “Faceplate and Controls”. 2. Big Foot Probe Also known as the Ground Microphone, this probe is to be used on hard surfaces, concrete, asphalt, tile, etc.
INSTRUMENT SET 3 On top of the Cylinder Probe is a three position toggle switch for Mute, Listen, and Momentary Listen. As with all Mute controls, learn to use them wisely. When tightening the sounds rods to the Hydrophonic Probe, secure the con- nector with a wrench as to not let it twist.
CONTROL PANEL 4 POWER This pad turns the XLT-30 On or Off. When the instrument is turned Off, all settings, or modifications to settings default to the preset factory set- tings. LIGHT Depress pad to turn the back light On or Off. Prolonged use of the Back Light will have minimal effect on the battery life of the XLT-30.
5 (The following filter modes have a frequency range from 60 Hz to 2.4 kHz) HI (High Range) – This filtering mode allows the user to adjust the response in the higher areas of the frequency range. Use the Arrow keys to increase or decrease this frequency response range.
6 OPERATING INSTRUCTIONS Set Up 1. Assemble Control Housing, Headset, and your choice of listening probe . The headset must be plugged in for the XLT-30 to operate. 2. Depress POWER pad to turn On the XLT-30. The XLT-30 goes through a five second warm up before the touch pads are functional.
7 OPERATING INSTRUCTIONS Use of the Notch Filter Occasionally, you may come across a sound that may be masking or covering your ability to adequately hear any leaks. This may be caused by nearby motors, fans, or many other annoyances. (Unfortunately, the most common are sounds caused by automobiles and traffic).
Subject to improvement or modification without notice. Fisher Research Laboratory does not warrant suitability to specific use. Fisher Research Laboratory shall in no event be liable for any direct, incidental, consequential or indirect damages. SPECIFICATIONS Operating frequency Range All pass mode 60Hz - 6kHz Filter mode 60Hz - 2.
.
QUALITY Fisher detectors are renowned for their quality. Each detector is hand crafted in the USA with pride PERFORMANCE The worldwide underground utility industry relys on Fisher. Our instruments are durable, dependable, and search deeper.. REPUTATION Fisher produced the first patented metal detector in 1931.
An important point after buying a device Fisher XLT-30 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fisher XLT-30 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fisher XLT-30 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fisher XLT-30 you will learn all the available features of the product, as well as information on its operation. The information that you get Fisher XLT-30 will certainly help you make a decision on the purchase.
If you already are a holder of Fisher XLT-30, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fisher XLT-30.
However, one of the most important roles played by the user manual is to help in solving problems with Fisher XLT-30. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fisher XLT-30 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
