Instruction/ maintenance manual of the product VCB-3574IR Fisher
Go to page of 15
INSTRUCTION MANUAL VCB-3574IR B/W CCD Camera About this manual B efo re in st a ll in g a nd us in g th e ca m e ra, pl ea se re ad th is ma nu al carefully.
SANYO INDUSTRIAL VIDEO B/W VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty .
Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer. CONTENTS INFORMATION TO USER ...........
Safety Guard THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT. WARNING: TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This installation should be made by a qualified service person and should conform to all local codes.
PRECAUTIONS In case of problem Do not use the camera if smoke or a strange odour comes from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Do not open or modify Do not open the cabinet, as it may be dangerous and cause damage to the unit.
PARTS NAMES 1 Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. 2 Line phase adjustment volume (LINE PHASE) When using two cameras or more, the image on the monitor may roll vertically when switching sources.
PARTS NAMES 8 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). 9 Flange-back adjustment screw (FLANGE BACK ADJ.) F Flange-back lock screw (FLANGE BACK LOCK) G Camera installation bracket The bracket can be fixed at the top or bottom of the camera.
PARTS NAMES Concerning auto-iris lenses DC type auto-iris lens A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is referred to as DC type coil lens or DC type non-amplifier lens. (Set the A.I. LENS switch to the DC position.
MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Checking the lens mount Do not use a lens if length “ L ” is more than 7 mm. If not, that may damage the camera and prevent proper installation. 1 Remove the lens mount cap from the camera.
MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 Prepare the lens cable. Cut th e ca ble at the plug, then rem ove a pprox. 8 mm of the cab le s heath an d st rip abo ut 2 m m fr om each wire .
CONNECTIONS Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately. 1 Make the video signal connection between the camera and the monitor or time lapse VCR. 2 Connect to 24 V AC UL listed class 2 power supply.
SETTINGS Control name Position a Electronic iris (EI)/Backlight compensation (BLC) switch OFF b Auto-iris lens switch (A.I. LENS) DC c Lens iris level volume (LEVEL) about centre Electronic iris function setting Use a manual or fixed iris lens and set the lens aperture to the shortest F stop.
SE TTING S Lens iris adjustment If using a DC type auto-iris lens, you will need to set the LEVEL (VR401) volume when shooting in the conditions described below. L (counterclockwise): To decrease the contrast H (clockwise): To increase the contrast • If shooting simultaneously in a dark room and through a bright window.
SETTINGS Line phase adjustment When using a camera switcher to connect 2 cameras or more to one monitor, there may be a vertical roll of the images when switched. In such a case, set as described below. Switch the display on the monitor from camera 1 to camera 2.
SPECIFICATIONS Scanning system : EIA standard (525 TV lines, 30 frames/sec.) Interlace : PLL 2:1 interlace Image device : 1/2 in ch so lid sta te i mage devi ce CCD Picture elements : 811 (H) x 508 (V.
An important point after buying a device Fisher VCB-3574IR (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fisher VCB-3574IR yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fisher VCB-3574IR - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fisher VCB-3574IR you will learn all the available features of the product, as well as information on its operation. The information that you get Fisher VCB-3574IR will certainly help you make a decision on the purchase.
If you already are a holder of Fisher VCB-3574IR, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fisher VCB-3574IR.
However, one of the most important roles played by the user manual is to help in solving problems with Fisher VCB-3574IR. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fisher VCB-3574IR along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
