Instruction/ maintenance manual of the product SK-1 Field Controls
Go to page of 12
STARKAP™ CHIMNEY CAP Model : SK - 1 The MODEL SK Starkap™ is designed for terminating gas vents or metal chimneys for gas or oil heating equipment.
Page 2 INSTALLATION REQUIRE MENTS 1. Install and secure the vertical vent, gas vent or metal chimney according to man ufacturer's instructions or in accordance with NFPA 54 National Fuel Gas code or applicable local codes.
Page 3 INSTALLATION 1. Before installation, apply two beads of high temperature sili cone sealant or equivalent around the bottom of the storm collar and 1 inch above the end of the Starkap™ body. (See Figure 2) 2. Insert the Starkap™ into the inside of the vent termination pipe, making sure the Starkap™ is seated against the storm collar.
Page 4 SPECIAL VENTING APPL ICATION INSTALLATION SHEET This sheet covers the requirements for installation of the Starkap™ for use with attached buildings designed for the purpose of housing heating equipment outside of the living space of the struct ure.
Page 5 STARKAP ™ Model : SK - 1 EXIGENCES D’INSTALLA TION 1. Installer et fixer l’évent vertical, l’évent à gaz ou la cheminée en métal conformément aux instructions du fabricant, au code national des gaz combustibles NFPA 54 ou à tout code local applicable.
Page 6 I NSTALLATION 1. Avant l’installation, appliquer deux cordons de scellant de silicone à haute température ou l’équivalent autour de la partie inférieure de la mitre et à 1 po au - dessus de l’extrémité du Starkap™. (Voir Le Schéma 2) 2.
Page 7 FEUILLE D’INSTALLATI ON POUR ÉVENT SPÉCIA L Cette feuille traite des exigences d’installation du Starkap™ sur des structures contiguës conçu es pour abriter du matériel de chauffage à l’extérieur de l’espace habitable d’une structure.
Page 8 StarKap™ M odel : SK - 1 REQUISITOS PARA LA I NSTALACIÓN 1. Instale y asegure el respiradero vertical, el respiradero de gas o la chimenea metálica según las instrucciones del fabricante o confirme al código Nacional sobre Gas Combustible, NFPA 54 o todo código lo cal correspondiente.
Page 9 INSTALACIÓN 1. Antes de la instalación, aplique dos gotas de compuesto sellador de silicona para altas temperaturas o un equivalente alrededor del fondo del collarín y una pulgada encima del extremo del cuerpo del Starkap™. (Ver Figura 2) 2.
Page 10 HOJA DE INSTALACIÓN PARA LA APLICACIÓN EN SITUACIONES ESPEC IALES DE VENTILACIÓN Esta hoja cubre los requisitos para la instalación del Starkap™ cuando se usa en edificios contiguos diseñados con el fin de alojar equipos de calefacción fuera de la estructura de habitación.
Page 11.
Page 12 PN 46263300 Rev C 09/00.
An important point after buying a device Field Controls SK-1 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Field Controls SK-1 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Field Controls SK-1 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Field Controls SK-1 you will learn all the available features of the product, as well as information on its operation. The information that you get Field Controls SK-1 will certainly help you make a decision on the purchase.
If you already are a holder of Field Controls SK-1, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Field Controls SK-1.
However, one of the most important roles played by the user manual is to help in solving problems with Field Controls SK-1. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Field Controls SK-1 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
