Instruction/ maintenance manual of the product 5900645 Ferris Industries
Go to page of 48
5100647 Revision T Tractor: Model Number: Description 5900633 CCWKAV19, 5900635 CCWKAV25, 5900637 CCWKAV19CE, 5900638 CCWKAV25CE, 5900972 CCWKAV26, Mower Deck: Model Number: Description 5900636 CCW/48.
Briggs & Stratton Power Products Group, LLC Copyright © 2012 Briggs & Stratton Corporation Milwaukee, WI, USA. All rights reserved. Ferris is a trademark of Briggs & Stratton Corporation Milwaukee, WI, USA. Contact Information: Briggs & Stratton Power Products Group, LLC 5375 N.
Safety Rules & Information ............................... 2 Identification Tags ............................................. 8 Safety Decals ...................................................... 9 Safety Interlock System .......................
2 Safety Rules & Information Operating Safety Congratulations on purchasing a superior-quality piece of lawn and garden equipment. Our products are designed and manufactured to meet or exceed all industry standards for safety. Do not operate this machine unless you have been trained.
3 Safety Rules & Information Slope Operation You could be seriously injured if you use this unit on too steep of a slope. Using the unit on a slope that is too steep where you do not have adequate footing and unit traction (and control) can cause you to lose control and possibly slip and fall or roll the unit over.
4 Safety Rules & Information Enclosed Areas Only operate this unit outdoors and away from unventilated areas such as inside garages or enclosed trailers. The engine emits poisonous carbon monoxide gas and prolonged exposure in an enclosed area can result in serious injury or death.
5 2. Mow only in the daylight or with good artificial light, keeping away from holes and hidden hazards. 3. Be sure all drives are in neutral and parking brake is engaged before starting engine. Only start engine from the operator’s position. Use seat belts if provided.
6 Safety Rules & Information 23. Use care when approaching blind corners, shrubs, trees or other objects that may obscure vision. 24. To reduce fire hazard, keep unit free of grass, leaves & excess oil. Do not stop or park over dry leaves, grass or combustible materials.
7 Safety Rules & Information SERVICE AND MAINTENANCE To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Safe Handling of Gasoline 1. Extinguish all cigarettes, cigars, pipes, and other sources of ignition.
8 www.ferrisindustries.com Identification Numbers North American Models CE Models SAMPLE SAMPLE When contacting your authorized dealer for replacement parts, service, or information you MUST have these numbers. Record your model/serial number and engine serial numbers on the space provided for easy access.
Safety Decals SAFETY DECALS Before operating your unit, read the safety decals. The cautions and warnings are for your safety. To avoid a personal injury or damage to the unit, understand and follow all the safety decals.
10 www.ferrisindustries.com Safety Interlock System / Safety Icons SAFETY INTERLOCK SYSTEM This unit is equipped with safety interlock switches. These safety systems are present for your safety, do not attempt to bypass safety switches, and never tamper with safety devices.
11 CE SAFETY ICONS Warning: Read Operator’s Manual. Read and understand the Operator’s Manual before using this machine. Danger: Thrown Objects. This machine is capable of throwing objects and debris. Keep bystanders away. Warning: Remove Key Before Servicing.
12 www.ferrisindustries.com CONTROL FUNCTIONS The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing require the combined use of several controls applied in specific sequences. To learn what combination and sequence of controls to use for various tasks see the OPERATION section.
13 Features & Controls Neutral Return Pedal The neutral return pedal provides a hands-free return to neutral. This is used in conjunction with the Reverse Speed Control Levers (B) to properly stop the machine. See the Operation section for steering instructions.
14 www.ferrisindustries.com CONTROL FUNCTIONS The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing require the combined use of several controls applied in specific sequences. To learn what combination and sequence of controls to use for various tasks see the OPERATION section.
15 Features & Controls Parking Brake Handle The parking brake is released by pushing DOWN on the parking brake handle until it stops. To engage the parking brake, pull UP on the handle until it locks over center. Engine Kill/Operator Presence Handles These handles are a major factor in the safety interlock system of the mower.
16 www.ferrisindustries.com GENERAL OPERATING SAFETY Before first time operation: • Be sure to read all information in the Safety and Operation sections before attempting to operate this tractor and mower. • Become familiar with all of the controls and how to stop the unit.
17 WARNING If you do not understand how a specific control functions, or have not yet thoroughly read the FEATURES & CONTROLS section, do so now. Do NOT attempt to operate the tractor without first becoming familiar with the location and function of ALL controls.
18 www.ferrisindustries.com Operation Figure 3. Forward Travel. A. Forward Speed Control Lever Figure 4. Reverse Travel. A. Reverse Steering Control Levers Figure 5.
19 Operation Figure 7. Increase Speed To The Left Wheel. A. Left Hand Forward Speed Override Lever Figure 8. Increase Speed To The Right Wheel. A. Right Hand Forward Speed Override Lever Figure 6.
20 www.ferrisindustries.com Operation MOWING Before mowing, set the cutting height as described in the Troubleshooting, Adjustments & Repair section. 1. Engage the parking brake. Make sure the PTO switch is disengaged and the motion control lever is in the NEUTRAL position.
21 When and How Often to Mow The time of day and condition of the grass greatly affect the results you’ll get when mowing. For the best results, follow these guidelines: 1. Mow when the grass is between three and five inches high. 2. Mow with sharp blades.
22 www.ferrisindustries.com PUSHING THE MOWER BY HAND 1. Disengage the PTO, engage the parking brake, turn the ignition OFF, and remove the key. 2. To disengage the transmissions (free-wheel position), lift the hydraulic release levers (A, Figure 9) located in front of the gas tank.
23 Operation STORAGE Temporary Storage (30 Days Or Less) Remember, the fuel tank will still contain some gasoline, so never store the unit indoors or in any other area where fuel vapor could travel to any ignition source. Fuel vapor is also toxic if inhaled, so never store the unit in any structure used for human or animal habitation.
24 www.ferrisindustries.com MAINTENANCE SCHEDULE & PROCEDURES The following schedule should be followed for normal care of your mower. You will need to keep a record of your operating time.
25 WARNING Gasoline is highly flammable and must be handled with care. Never fill the tank when the engine is still hot from recent operation. Do not allow open flame, smoking or matches in the area. Avoid over-filling and wipe up any spills. Do not remove fuel filter when engine is hot, as spilled gasoline may ignite.
26 www.ferrisindustries.com CHECK HYDRAULIC OIL LEVEL 1. Observe the oil reservoir (B, Figure 11). The oil level should be at the “FULL” line (C). 2. Before removing the reservoir cap, make sure the area around the reservoir cap is free of dust, dirt, or other debris.
27 Regular Maintenance Figure 15. Lubrication Points Mower Deck Lubrication Points* LUBRICATION Lubricate the unit at the locations shown in Figure 15 as well as the following lubrication points.
28 www.ferrisindustries.com Regular Maintenance CLEANING THE BATTERY AND CABLES 1. Disconnect the cables from the battery, negative cable first (B, Figure 16). 2. Clean the battery terminals and cable ends with a wire brush until shiny. 3. Reinstall the battery and reattach the battery cables, positive cable first (A).
29 SERVICING THE MOWER BLADES 1. Blades should be sharp and free of nicks and dents. If not, sharpen blades as described in following steps. 2. Remove the deck guard. 3. Raise the mower deck and secure with jack stands. 4. To remove blade for sharpening, use two (2) 15/16” wrenches to remove the nut from the top of the blade bolt.
30 www.ferrisindustries.com TROUBLESHOOTING While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly. The troubleshooting guide below lists the most common problems, their causes and remedies.
31 Rider Troubleshooting Continued. PROBLEM CAUSE REMEDY Engine runs, but mower will 1. Transmission release lever(s) 1. Move into drive position. not drive. in “neutral” position. 2. Belt is broken. 2. See Drive Belt Replacement. 3. Drive belt slips.
32 www.ferrisindustries.com Troubleshooting, Adjustment & Repair TROUBLESHOOTING COMMON CUTTING PROBLEMS PROBLEM CAUSE REMEDY Streaking. 1. Blades are not sharp. 1. Sharpen your blades. 2. Blades are worn down to far. 2. Replace your blades. 3. Engine speed is too slow.
33 Troubleshooting, Adjustment & Repair MOWING HEIGHT ADJUSTMENT See Figure 20. The mowing height adjustment can be changed by turning the cutting height adjustment handle. To Raise the Mower Deck: Turn the cutting height adjustment handle (A, Figure 20) clockwise.
34 www.ferrisindustries.com Troubleshooting, Adjustment & Repair B A Figure 23. Lift Rod Clevis Adjustment A. Clevis, 1/2-20 B. 1/2-20 Jam Nut C. Cotter Pin D. Clevis Pin E. Rear Deck Lift Rod D C E DECK LEVELING ADJUSTMENT NOTE: Before adjusting the deck level, the deck lift rod timing must be checked and/or adjusted.
35 Troubleshooting, Adjustment & Repair Figure 26. Deck Level Adjustment A. Jam nut B. Adjustment Bolt C. Chain Hanger Clevis A B C 6. Manually position the left hand mower blade so that the tip of the blade is pointing towards the front and back of the mower.
4. Slide the drive belt over the edge of the stationary idler pulley (B). Carefully release the tension on the breaker bar until the idler arm comes to a stop. 6. Unhook the idler tension spring (C) from the anchor bolt (D). Remove the old belt and replace with a new one.
TRANSMISSION DRIVE BELT REPLACEMENT 1. Remove the deck drive belt. See MOWER BELT REPLACEMENT sections. 2. Remove the clutch anchor bolts (A, Figure 30) that fasten the clutch anchor pad to the anchor. 3. Unplug the PTO clutch from the wire harness. 4.
38 www.ferrisindustries.com Troubleshooting, Adjustment & Repair TRANSMISSION NEUTRAL & TRACKING ADJUSTMENTS Neutral Adjustment 1. Park the machine on a smooth, level surface such as a concrete floor, away from bystanders and preferably facing a wall.
39 Troubleshooting, Adjustment & Repair TRANSMISSION MAINTENANCE The hydrostatic transmissions are sealed units that require no maintenance other than the following. • Keep the machine and the transmission cooling fins clear or grass, leaves and debris.
40 www.ferrisindustries.com Troubleshooting, Adjustment & Repair BATTERY SERVICE Checking Battery Voltage A voltmeter can be used to determine condition of battery. When engine is off, the voltmeter shows battery voltage, which should be 12 volts.
41 To Starter Switch Starting V ehicle Battery T o Ground To Starter Switch Dischar g ed V ehicle Battery Engine Block THIS HOOK-UP FOR NEGA TIVE GROUND VEHICLES MAKE CERT AIN VEHICLES DO NO T TOUCH J.
42 www.ferrisindustries.com Specifications SPECIFICATIONS NOTE: Specifications are correct at time of printing and are subject to change without notice. ENGINE: 19 Gross HP† Kawasaki Make Kawasaki Model FH580V Displacement 35.7 Cu. in (585 cc) Electrical System 12 Volt, 13 amp, Alternator, Battery: 340 CCA Oil Capacity 1.
THIS IS A 15 DEGREE SLOPE INSTRUCTIONS 1. Fold this page along the dotted line indicated above. 2. Align the left edge of this guide with a vertical tree , a power line pole, a fence post, or any vertical structure. 3. Compare the angle of the fold with the angle of the hill.
Notes.
Thank you for purchasing Ferris commercial mowing equipment. Please take a few minutes to read this limited warranty information. It contains all the information you will need to have your Ferris mower repaired in the unlikely event that a breakdown covered by this limited warranty should occur.
Comfort Control DD Series Walk-Behind Mowers OPERATOR’S MANUAL.
An important point after buying a device Ferris Industries 5900645 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ferris Industries 5900645 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ferris Industries 5900645 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ferris Industries 5900645 you will learn all the available features of the product, as well as information on its operation. The information that you get Ferris Industries 5900645 will certainly help you make a decision on the purchase.
If you already are a holder of Ferris Industries 5900645, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ferris Industries 5900645.
However, one of the most important roles played by the user manual is to help in solving problems with Ferris Industries 5900645. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ferris Industries 5900645 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
