Instruction/ maintenance manual of the product DVI-RGB 200 Extron electronic
Go to page of 19
68-1791-01 Rev. A 10 10 DVI to Analog RGB Video Interface DVI-RGB 200 User Guide Interfaces.
This symbol is intended to alert the user of important operating and mainte- nance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’ s enclosure that may present a risk of electric shock.
FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference.
Contents Introduction ............................................ 1 Installation and Operation ..................... 2 Installation Overview ........................................ 2 Mounting the Interface .................................... 2 Rear Panel Connections and Controls .
DVI-RGB 200 • Contents iv.
Intr oduction The Extron DVI-RGB 200 DVI to analog RGB video interface converts DVI digital video to analog RGB video. The interface accepts a single link of digital-only Digital Visual Interface (DVI-D) video from a computer , or other digital video sour ce device, on a standar d 29-pin female DVI-I connector .
Installation and Operation This sections details the installation and operation of the DVI-RGB 200, including: • Installation Overview • Mounting the Interface • Rear Panel Connections and Contr.
Rear Panel Connections and Contr ols 100-240V 0.4A 50/60 Hz OUTPUT DVI-DINPUT BUFFERED LOOP-THROUGH R H G V B S SOG ON/OFF REFRESH EDID SOURCE MONITOR HIGH LOW SELECTOR EDID SELECT DVI-RGB 200 2 1 5 7 3 6 4 Figure 2.
f DIP switches — SOG (Sync on Green) On/Of f switch — Set this switch to the On (up) position to enable SOG for RGsB video. Set this switch to the Off (down) position to disable SOG for RGBS or RGBHV video.
Fr ont Panel Controls and Indicator DVI-RGB 200 DVI TO RGB CONVE RT ER BOOST LEVEL CONTROL PEAK 8 9 10 Figure 4. DVI-RGB 200 Fr ont Panel h Power LED — The two-tone Power LED lights amber or green: • Amber when the DVI-RGB 200 is receiving power but no DVI input signal is applied.
Operation After the DVI-RGB 200 and its connected devices are power ed up, the system is fully operational. If you encounter any problems, verify that the cables ar e r outed and connected properly .
Refer ence Information This section discusses the specifications, part numbers, and accessories for the DVI-RGB 200. T opics that are cover ed, include: • Specifications • Part Numbers • Mounting the Interface Specifications Video NOTES: • The DVI-RGB 200 converts a single link DVI signal to an analog RGB signal .
Sync Output type ................................... RGBHV , RGBS, RGsB Output level ................................... TTL (5 Vp-p, unterminated) Output impedance ......................... 75 ohms Polarity ...........................................
Part Numbers Interface Part Numbers These items are included in each or der for a DVI-RGB 200: Interface and included parts Part number DVI-RGB 200 60-1064-01 IEC power cord T weeker (small screwdrive.
Mounting the Interface CAUTION: Installation and service must be performed by authorized personnel only . The 1U high, half rack width DVI-RGB 200 can be placed on a tabletop, mounted on a rack shelf, or mounted under a desk or tabletop.
Rack shelf mounting instructions The unit can be mounted in the front or the r ear of the rack. 1. Remove the feet from the bottom of the unit if installed. 2. Mount the unit on the rack shelf, using two 4-40 x 3/16-inch screws in opposite (diagonal) corners to secure it to the shelf (figure 5).
Furniture Mounting Under -Fur niture Mounting The unit can be mounted under a horizontal surface using an optional MBU 125 under -desk mounting kit (part #70-077-01). Mount the unit under a desk or table as follows: 1. Remove feet from the bottom of the unit if installed.
Through-furniture mounting The interface can be mounted through a desk or other furniture using an optional Extr on MBD 129 through-desk mounting kit (part #70-077-02). Mount the unit thr ough a desk or table as follows (figure 8): Figure 8. Thr ough-desk Mounting 1.
Extr on ® W arranty Extron Electr onics warrants this pr oduct against defects in materials and workmanship for a period of three years from the date of pur chase.
An important point after buying a device Extron electronic DVI-RGB 200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Extron electronic DVI-RGB 200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Extron electronic DVI-RGB 200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Extron electronic DVI-RGB 200 you will learn all the available features of the product, as well as information on its operation. The information that you get Extron electronic DVI-RGB 200 will certainly help you make a decision on the purchase.
If you already are a holder of Extron electronic DVI-RGB 200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Extron electronic DVI-RGB 200.
However, one of the most important roles played by the user manual is to help in solving problems with Extron electronic DVI-RGB 200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Extron electronic DVI-RGB 200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
