Instruction/ maintenance manual of the product AT-6101GP Allied Telesis
Go to page of 34
613-001673 Rev B AT-6101GP Power over Ethernet Injector AT-6101GP PoE Injector Installation Guide.
Copyright © 2012 Allied Telesis, Inc. All rights reserved. No part of this pub lication may be reproduced without prior wr itten permission from Al lied Telesis, Inc. Allied Telesis and th e Allied Telesis logo are trademarks of Allied Telesis, Incor porated .
3 Electrical Safety and Emissions St a n d a r d s This product meets the following standards. RFI Emissions FCC Class B, CISPR 22 Class B, EN55022 Class B, VCCI Class B, C-TICK Immunity EN55024 Electrical Safety UL 60950-1 ( C UL US ), EN60950 (TUV), CE U.
Chapter : 4 T ranslated Safety S tatements Important: The indicates that a translation of th e safety statement is available in a PDF document titled “Translated Safety State ment s” posted on the Allied Telesis website a t www.alliedtelesis.com .
1 Preface ........ ................ ................ ................. ................ ................ ................ ................ ............................. ........ 7 Document Conventions .............. ................ ................ .
Contents 2.
3 List of Figur es Figure 1. AT-6101GP PoE Injector ........................................................ ............................ .......... .. ........... ........... .............. .. 14 Figure 2. AC Power Input Connector ........... .......
Figures 4.
5 Table 1. Twisted Pair Cable for th e 10/100/1000Base-T Ports ....... .............. ........... .............. ........... ......... ...................... .. 13 Table 2. 10/100Base-TX Por t LEDs ........ ........... ........... ........... ........
Tables 6.
7 Pr eface This guide contains the installat ion instructions for the AT-6101 PoE Injector Installation Guide. This p ref ace contains the following sections: ❒ “Document Conventions” on p age 8.
Preface 8 Document Conventions This document uses the following conventions: Note Notes provide additional informatio n. Caution Cautions inform you t hat performing or omitting a specific action may result in equipment damage or loss of data. Warning Warnings inform you that performing or omitting a sp ecific action may result in bodily injury.
AT-6101 PoE Injector Instal lation Guide 9 Allied Telesis Contact Information If you need assistance with this prod uct, you may contact Allied Telesis technical support by going to the Suppo rt & Services section of the Allied Telesis web site at www.
Preface 10.
11 Chapter 1 Overview This chapter contains the following sections: “Features” on p age 12 “Hardware Description ” on p age 14 “LEDs” on p age 15.
Chapter 1: Ove rview 12 Features Here are the features of this prod uct: AT-6101GP PoE Injector The major features of the AT-6101GP PoE In jector are: Power over Ethernet Injector for 10/100/1000B.
AT-6101 PoE Injector Instal lation Guide 13 Cable Requirements The cable requirements of the ports are given in Table 1. Port Pinouts Refer to Table 7 on page 28 for the port pinouts of the 10/100Base-TX/1000Base-T twisted pair ports.
Chapter 1: Ove rview 14 Hardware Description The AT-6101GP PoE Injector is shown in Figure 1. Figure 1. AT-6101GP PoE Injector DA T A IN Port: This port, shown in Figure 1, in is an RJ-4 5 Ethernet connector where dat a is received and tran smitted through the A T -6101GP PoE Injector.
AT-6101 PoE Injector Instal lation Guide 15 LEDs The LEDs of the AT-6101GP PoE Injector are shown in Fig ure 3 and described in Table 2. Figure 3. AT-6101GP LEDs T able 2. 10/100Base-TX Po rt LEDs LED State Description AC Power Off No AC power is being provided to the unit.
Chapter 1: Ove rview 16.
17 Chapter 2 Installation You may install the AT-6101 GP PoE Injector on a table or on a wall. This chapter contains the following installation procedures: “Reviewing Safety Precautions” on p .
Chapter 2: Inst allation 18 Reviewing Safety Precautions Please review the following safety precautions before you begin to perform the installation procedure. Note The indicates that a tra nslation of the safety statement is available in a PDF document titled Tran slated Safety Statements .
AT-6101 PoE Injector Instal lation Guide 19 Warning Only trained and qualified personn el are allowed to install or replace this equipment. E14 Circuit Overloading: Consideratio n should be given .
Chapter 2: Inst allation 20 Choosing a Site for the AT-6101GP PoE Injector Observe these guidelines when pl anning the installation of the AT-6101GP If you plan to install the power injector on a table, the table should be level and stable . The power outlet should be located near the power injector and be easily accessible.
AT-6101 PoE Injector Instal lation Guide 21 Unpacking the AT-6 101GP PoE Injector The AT-6101GP PoE Injector comes with the items listed in Table 4. Verify that the contents of the shipping conta iner matches the items listed.
Chapter 2: Inst allation 22 Installation Procedures Depending on where you install the unit. perform the following proced ures when installing the AT-6101GP PoE Inje ctor: ”T able T op Installat.
AT-6101 PoE Injector Instal lation Guide 23 2. Install the two wall ancho rs into the wall at the loca tions marked in the previous step. The anchors require 0.635 mm (0.25 in.) h oles. 3. Hold the power injector on the wall so that the mounting h oles align with the anchors previously installed.
Chapter 2: Inst allation 24 AC Power Cord Installation Depending on your installation, con nect the AC power cord as shown in Figure 8 (table top installation) or Figure 9 (wall installation). Figure 8. Connecting AC Power Cord for Tab le Top Installation Figure 9.
25 Chapter 3 T r oubleshooting This chapter contains suggestions on ho w to trou bleshoot the installation of the AT-6101GP PoE Injector if a problem occurs. Problem: All PoE injector LEDs are off even though the ports are conne cted to network devices.
Chapter 3: Tro ubleshooting 26.
27 Appendix A T echnical Specifications Physical Specifications Environmental Specifications Power Specifications T able 3. Physical S pecifications Dimensions (H x W x D) 36 mm x 65 mm x 140 m Weight 300 grams (0.
Appendix A: Technica l Specifications 28 Certifications RJ-45 Twisted Pair Port Pinouts Figure 10 illustrates the pin layout of th e RJ-45 connectors an d ports. Figure 10. RJ-45 Socket Pin Layout (Front View) Table 7 lists the pin signals for 10 a nd 100 Mbps.
AT-6101 PoE Injector Instal lation Guide 29 Table 8 lists the pin sig nals when a port operating at 1 000 Mbps. T able 8. Pin Signals for 1000 Mbp s Pinout Pair 1 Pair 1 + 2 Pair 1 - 3 Pair 2 + 4 Pair.
Appendix A: Technica l Specifications 30.
An important point after buying a device Allied Telesis AT-6101GP (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Allied Telesis AT-6101GP yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Allied Telesis AT-6101GP - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Allied Telesis AT-6101GP you will learn all the available features of the product, as well as information on its operation. The information that you get Allied Telesis AT-6101GP will certainly help you make a decision on the purchase.
If you already are a holder of Allied Telesis AT-6101GP, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Allied Telesis AT-6101GP.
However, one of the most important roles played by the user manual is to help in solving problems with Allied Telesis AT-6101GP. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Allied Telesis AT-6101GP along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
