Instruction/ maintenance manual of the product BlackDiamond 8800 Series Extreme Networks
Go to page of 180
Extreme Networks, Inc. 3585 Monroe Street Santa Clara, California 9505 1 (888) 257-30 00 (408) 579-28 00 http://www . extremenetworks.com BlackDiamond 8800 Series Switches Hardware Installation Guide Published: Augu st 2008 Part number: 100284-00 Rev .
BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 2 AccessAdapt, Alpi ne, BlackDiamond, ESRP , Ethernet Ev er ywher e, Extreme Enabl ed, Extreme E thernet Everywher e, Extreme Networks, .
BlackDiamond 8800 S eries Switches Hardware Installation Guide 3 T able of Contents Preface............................................................... ........................................... ............................... .. 9 Introduction ..
Table of Contents BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 4 Port LEDs on Non-PoE Modules ............. .......................... ..................... ..........................39 Port LEDs on PoE Modules (G48P, G48Pe, an d G48Tc or G48Te2 with S-POE Card) .
Table of Co ntents BlackDiamond 8800 S eries Switches Hardware Installation Guide 5 AC Power Cable Requirements ................................ .......................... ..................... ............... 67 Replacing the Power Cable ............
Table of Contents BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 6 Initial Management Access ............................... ..................... ..................... .......................... ... 114 Connecting Equipment to the Console Port .
Table of Co ntents BlackDiamond 8800 S eries Switches Hardware Installation Guide 7 Installing Power Supply Units .................................. .......................... .................... .................. .1 5 5 Maintenance Safety .........
Table of Contents BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 8.
BlackDiamond 8800 S eries Switches Hardware Installation Guide 9 Preface This preface pr ovides an overvie w of this guide, describes guid e conventions, and lists other publications that might b e useful. WAR NI NG ! Service to all equipment should be performed by trained and qualified se rvice personnel only .
Preface BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 10 Related Publications The Extre me Networks Extre meXOS™ switch documentation set includes: ● ExtremeXOS 12.1 Concepts Guide ● ExtremeXOS 12.1 Command Reference Guide ● ExtremeXOS 12.
Related Public ations BlackDiamond 8800 S eries Switches Hardware Installation Guide 11 Y ou can select an d download the following E xtrem e Networks documentation fr om the Documentation Overview page: ● Software User Guides ● Hardwar e User Guides Y ou can find archived user guid es for softwar e at: http://www .
Preface BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 12.
1 About the BlackDiamond 8800 Series Switches.
.
BlackDiamond 8800 S eries Switches Hardware Installation Guide 15 1 About the BlackDiamond 8800 Series Switches This chapter describes the Extreme Networks Blac kDiamond 8800 series switches and inclu.
About the BlackDiamo nd 8800 Series Switches BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 16 Full-Duplex Support Extreme Networks switches provide full-dupl ex suppo rt for all ports. Full-d uplex support means that frames can be transmitted and received simultaneous ly , effectively doubling the bandwidth available on a link.
BlackDiamond 8806 Switch Chassis BlackDiamond 8800 S eries Switches Hardware Installation Guide 17 Figure 1 shows the fr ont of a BlackDiamond 8806 chassi s equipped with tw o MSMs and three optional I/O modules. Figure 1: Front of the BlackDiamond 880 6 Chassis Figure 2 shows the r ear panel of th e BlackDiamond 8806 chassis.
About the BlackDiamo nd 8800 Series Switches BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 18 BlackDiamond 8810 Switch Chassis The BlackDiamond 8810 chassis consists of the f ollowin.
BlackDiamond 8810 Switch Chassis BlackDiamond 8800 S eries Switches Hardware Installation Guide 19 Figure 4: Rear Panel of the BlackDi amond 8810 Chassis The rear panel of the BlackDiamond 8810 chassi.
About the BlackDiamo nd 8800 Series Switches BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 20.
BlackDiamond 8800 S eries Switches Hardware Installation Guide 21 2 BlackDiamond 8800 Series Modules This chapter describes modules for the BlackDiamo nd 8800 s eries of switches and includes the foll.
BlackDiamond 8800 Seri es Modules BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 22 Selection of the primary MSM occurs a utomatically . The following examples describe the select ion process: ● When a switch boots with two MSMs installed, the MSM in the lower -numbered s lot becomes the primary MSM.
Management Sw itch Modules (MSM) BlackDiamond 8800 S eries Switches Hardware Installation Guide 23 Figure 7 shows the MSM-48c. Figure 7: MSM-48c The BlackDiamond 8800 series MSMs have the following features on the front panel: ● Console port—DB-9 serial port used to conne ct a terminal and perform local management.
BlackDiamond 8800 Seri es Modules BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 24 MSM LEDs Ta b l e 3 describes the LED activity on th e BlackDiamond 8800 series MSMs. NOTE The LEDs on the management Ethernet port are not labeled. On most modules, the LED on the right is the link LED, and the one on the left is the activity LED.
I/O Modules BlackDiamond 8800 S eries Switches Hardware Installation Guide 25 No configuration information is stored on the I/O mo dules; all configuration information i s stored on the MSMs. When a BlackDiamond 8800 series switch is powered on, the software generates a default configuration for any slots that contain I/O modules.
BlackDiamond 8800 Seri es Modules BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 26 Figure 8: G24X I/O Module The default configuration of the G24X modu le is as fo llows.
I/O Modules BlackDiamond 8800 S eries Switches Hardware Installation Guide 27 G48T I/O Module The G48T I/O module ( Figure 10 ) has 48 autosensing 10/10 0/1000BASE- T ports that use standard RJ-45 connectors. Figure 10: G48T I/O Module The default configuration of the G48T I/O module i s as follows.
BlackDiamond 8800 Seri es Modules BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 28 G48P I/O Module The G48P I/O module ( Figur e 1 1 ) has 48 au tosensing 10/100/1000BASE -T ports that use standard RJ-45 connectors.
I/O Modules BlackDiamond 8800 S eries Switches Hardware Installation Guide 29 CAUTION BlackDiamond a-series modules require specific minimum vers ions of ExtremeXOS software to be recognized by the MSM (see Ta b l e 4 ). Software builds earlier than the listed vers ions do not supp ort th e specified I/O modules.
BlackDiamond 8800 Seri es Modules BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 30 G48Xa I/O Module The G48Xa I/O module ( Figure 13 ) has 48 1000BASE-X ports that use SPF fiber SFP connectors. Figure 13: G48Xa I/O Module The default configuration of the G48X a module is as follows.
I/O Modules BlackDiamond 8800 S eries Switches Hardware Installation Guide 31 10G4Xa I/O Module The 10G4Xa I/O module ( Figure 14 ) has four XFP-based 10-gigabit Ethernet ports. Figure 14: 10G4Xa I/O Modul e The default configuration of the 10G4Xa I/O module is as follows.
BlackDiamond 8800 Seri es Modules BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 32 BlackDiamond 8800 c-Series I/O Modules The BlackDiamond 8800 c-series of I/O module s consists of t.
I/O Modules BlackDiamond 8800 S eries Switches Hardware Installation Guide 33 The G48T c I/O module has the following LEDs: ● Module status ● Module diagnostics ● Port status ● POE present For information about the LEDs and their activity on the G48T c I/O module, see “I/O Module LEDs” on page 38 .
BlackDiamond 8800 Seri es Modules BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 34 10G8Xc I/O Module The 10G8Xc I/O module Figure 1 8 has eight unpopulated XFP-based 10-gigabit Ethernet ports. This module is over -subscribed 2:1. Figure 18: 10G8Xc I/O Modul e The default configuration of the 10G8Xc I/O module is as follows.
I/O Modules BlackDiamond 8800 S eries Switches Hardware Installation Guide 35 The G24Xc I/O module has the following LEDs: ● Module status ● Module diagnostics ● Port status For information about the LEDs and their activity on the G24Xc I/O modu le, see “I/O Module LEDs” on page 38 .
BlackDiamond 8800 Seri es Modules BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 36 BlackDiamond 8800 E-Series I/O Modules The BlackDiamond 8800 e-series of I/O modules include: ● G.
I/O Modules BlackDiamond 8800 S eries Switches Hardware Installation Guide 37 G48Pe I/O Module The G48Pe I/O module ( Figur e 22 ) has 48 autosensing 10/100/1000 B ASE-T ports that use standard RJ-45 connectors. In addition to the Ethernet conne ction, these ports can deliver Power over Ethernet (PoE) to an attached device, using the same cabl e.
BlackDiamond 8800 Seri es Modules BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 38 G48T e2 I/O Module The G48T e2 I/O module ( Figure 21 ) has 48 autosensing 10/100/1000BASE-T p orts that use standard RJ-45 connectors.
I/O Modules BlackDiamond 8800 S eries Switches Hardware Installation Guide 39 Module LEDs Ta b l e 5 describes the LED activity for all BlackDiamond 8800 series I/O modules. Port LEDs on Non-PoE Modules This section describes the port LEDs for non-PoE BlackDiamond 8800 series I/O modules and for por t option cards ins talled in the MSM- 8c.
BlackDiamond 8800 Seri es Modules BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 40 Port LEDs on PoE Modules (G48P , G48Pe, and G48T c or G48T e2 with S-POE Card) This section describes the port LEDs for BlackDia mond 8800 series I/O modules that support PoE.
BlackDiamond 8800 S eries Switches Hardware Installation Guide 41 3 Power Supply Units for BlackDiamond 8800 Series Switches This chapter includes the foll owing sections: ● Overview of BlackDiamond.
Power Supply Units for Bla ckDiamond 8800 Serie s Switches BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 42 Extreme Networks 700/1200 W AC PSU Figure 24 shows the Extr eme Networks 700/1200 W AC UL-listed accessory power supply unit (Model # 6002 0/PS 2336).
Extreme Networks 700/1200 W AC PSU BlackDiamond 8800 S eries Switches Hardware Installation Guide 43 Power Supply Cords Extreme Networks 700/1200 W AC PSUs are shipped with both 1 10 V AC and 220 V AC power supply cords. The 1 10 V AC power supply cord allows a maximum DC out put power of 700 W .
Power Supply Units for Bla ckDiamond 8800 Serie s Switches BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 44 Specifications The 700/1200 W AC PSU functions from 90 V to 264 V and 47 Hz to 63 Hz AC Input.
Extreme Networks 600/900 W AC PSU BlackDiamond 8800 S eries Switches Hardware Installation Guide 45 Extreme Networks 600/900 W AC PSU Figure 25 shows the Extreme Networks 600/900 W AC UL-l isted accessory pow er supply unit (Model # 41050/ PS 2431). This power supply is compatible with the BlackDiamond 8806 switch.
Power Supply Units for Bla ckDiamond 8800 Serie s Switches BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 46 software does not recognize the 600/900 W AC PSU and the PSU will not be budgeted pr operly , possibly resulting in PSU shutdown and/or cha ssis reboot.
Combining Diff erent AC P SU Models BlackDiamond 8800 S eries Switches Hardware Installation Guide 47 Make sure that the 600/900 W AC PSU circuit is not over loaded. Use proper over -curre nt protection, such as a circuit-breaker , to prevent over-current conditions.
Power Supply Units for Bla ckDiamond 8800 Serie s Switches BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 48 Extreme Networks 1200 W DC PSU Figure 26 shows the Extr eme Networks 1200 W DC UL-listed accessory power supply un it (Model # 6002 1/PS 2350).
Extreme Networks 1200 W DC PSU BlackDiamond 8800 S eries Switches Hardware Installation Guide 49 not be used together in the same BlackDiamond switch. For central DC power connections, the 12 00 W DC .
Power Supply Units for Bla ckDiamond 8800 Serie s Switches BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 50.
2 Installing BlackDiamond 8800 Series Switches.
and Modules.
BlackDiamond 8800 S eries Switches Hardware Installation Guide 53 4 Site Preparation This chapter includes the foll owing sections: ● Planning Y our Site on page 53 ● Meeting Site Require ments on.
Site Preparation BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 54 ● Meeting power r equire ments T o run your equipment safely , you must meet the specific power requir ements for each power supply unit installed in th e system.
Meeting Site Requirements BlackDiamond 8800 S eries Switches Hardware Installation Guide 55 the electronics industr y . The addr ess is EIA; 2500 W ilson Bou levard; Arlington, V irginia 22201 USA.
Site Preparation BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 56 NOTE As with all electrical equipment, Ex treme Networks product lifetimes degr ade with increased temperature. If possible, temperatures should be kept at approximately 78 ° F (25 ° C ) o r l o w e r .
Meeting Site Requirements BlackDiamond 8800 S eries Switches Hardware Installation Guide 57 Figure 28: Airflow Through the BlackDiamond 8810 Chassis Electrostatic Discharge Y our syst em must be protected from static electricit y or electrostatic dischar ge (ESD).
Site Preparation BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 58 Figure 29: Using an ESD-preven tive Wrist Strap Rack Specifications and Recommendations Racks should conform to conventional standards. In th e United States, u se EIA Standar d RS-3 10C: Racks, Panels, and Associated Equi pment.
Meeting Site Requirements BlackDiamond 8800 S eries Switches Hardware Installation Guide 59 At a minimum, follow these guidelines to gr ound equipment racks to the earth gr ound: ● CAD weld appropriate wir e terminals to building I-beams or earth gr ound r ods.
Site Preparation BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 60 Figure 30: Properly Secured Rack Brace open equipme nt racks if the channel thic kness is less than 1/4 i nch (6.
Evaluating and Me eting Cable Requirements BlackDiamond 8800 S eries Switches Hardware Installation Guide 61 ● Isolate faults in the distribution system . ● Locate the opposite end of any cable. ● Know the types of network devices that your cabling infrastructure can support.
Site Preparation BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 62 Figure 3 1: Properly Installed and Bundled Cab le SPG_00 8 Proper bundling of cables Cable managers supporting and d.
Evaluating and Me eting Cable Requirements BlackDiamond 8800 S eries Switches Hardware Installation Guide 63 Fiber Optic Cable Fiber optic cable mu st be handled carefully duri ng installation. Every ca ble has a minimum bend radius, for example, and fibe r s w i l l b e d a m a g e d i f t h e c a b l e s a r e b e n t t o o s h a r p l y .
Site Preparation BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 64 * Proprietary to E xtreme Networks. Connections bet ween two Ex tr eme Networ ks 1000BASE-L X interfaces t hat use 10/1 25 μm single-mode fiber can use a maximum distance of 10,000 met ers.
Evaluating and Me eting Cable Requirements BlackDiamond 8800 S eries Switches Hardware Installation Guide 65 Radio Frequency Interference If you use UTP cabling in an installat ion, take precau tions to avoid RF interfer ence.
Site Preparation BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 66 Meeting Power Requirements This section describes power requirements, including: ● PoE Devices ● Power Supply Re.
Meeting Power R equirements BlackDiamond 8800 S eries Switches Hardware Installation Guide 67 AC Power Cable Requirements Use an AC power cable appropriate for your country . Check your local electr ical codes and regulatory agencies for power cable r equir ements.
Site Preparation BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 68 ● Monitor and log power supply status. ● Display the volta ge (current draw) of the equipment. ● Restart equipment after a long power outage. ● Display the volta ge currently on the line.
Applicable Indust ry Standards BlackDiamond 8800 S eries Switches Hardware Installation Guide 69 Y ou can access these standards at: http://www . ansi.
Site Preparation BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 70.
BlackDiamond 8800 S eries Switches Hardware Installation Guide 71 5 Installing the BlackDiamond 8800 Series Chassis This chapter includes the foll owing sections: ● Unpacking the BlackDiamond 8806 C.
Installing the BlackDi amond 8800 Series Chassis BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 72 Unpacking the BlackD iamond 8806 Chassis NOTE Do not remove the nylon straps until you are ready to open the chassis package. CAUTION The BlackDiamond 8806 chassis weighs almo st 65 pounds.
Unpacking the BlackDia mond 8806 Chassis BlackDiamond 8800 S eries Switches Hardware Installation Guide 73 Figure 35: Clip Locks on the BlackD iamond 8806 Chassis Shipping Carton 4 Slide the shipping carton up over the BlackDiamond 8806 chassis (see Figur e 36 ).
Installing the BlackDi amond 8800 Series Chassis BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 74 6 At each side of the chassis, place one hand in an empty power supply bay and the other hand in the recessed hand-hold on the back panel of the chassi s.
Unpacking the BlackDia mond 8810 Chassis BlackDiamond 8800 S eries Switches Hardware Installation Guide 75 Unpacking the BlackD iamond 8810 Chassis CAUTION The BlackDiamond 8810 chassis weighs almo st 80 pounds. Proper lifting and moving of the chassis requires two people.
Installing the BlackDi amond 8800 Series Chassis BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 76 Figure 39: Rem oving Contents from the B lackDiamond 8810 Up per Shipping Ca rton 3 Release the clip locks as shown in Figure 35 . a Place your thumb and index finger inside the clip lock to grasp the prongs.
Unpacking the BlackDia mond 8810 Chassis BlackDiamond 8800 S eries Switches Hardware Installation Guide 77 Figure 41: Unpa cking the Black Diamond 8810 Chassis 6 At each side of the chassis, place one hand in an empty power supply bay and the other hand in the recessed hand-hold on the back panel of the BlackDiamond 8810 chassis (see Figur e 37 ).
Installing the BlackDi amond 8800 Series Chassis BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 78 NOTE Save all packaging, bolts, washer s, and clip locks, as well as the box and pallet, for future use in the event that the chassis must be moved to another locat ion or returned to Extreme Networks.
Attaching the Mid-Mount Brack ets BlackDiamond 8800 S eries Switches Hardware Installation Guide 79 CAUTION The BlackDiamond 8806 ch assis weighs almost 65 poun ds., and the BlackDiamond 8810 chassis weighs almost 80 pounds. Proper lifting and moving of the chassis requires two people.
Installing the BlackDi amond 8800 Series Chassis BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 80 Figure 44: Attaching the Mid-mount Bracke ts to the BlackDiamond 8810 Chassis Rack-M.
Rack-Mounting th e BlackDiamond 8800 Series Ch assis BlackDiamond 8800 S eries Switches Hardware Installation Guide 81 Figure 45: Mou nting the 19-in ch Helper Bracket o nto the System Rac k 4 Lift the back of the empty BlackDiamond 8 800 se ries chassis onto the 19-inch helper bracket.
Installing the BlackDi amond 8800 Series Chassis BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 82 Figure 46: Se curing the Blac kDiamond 8806 Chassis to a Rack EX_171A.
Grounding the BlackDiam ond 8800 Series Chassis BlackDiamond 8800 S eries Switches Hardware Installation Guide 83 Figure 47: Se curing the Blac kDiamond 8810 Chassis to a Rack 7 Remove the helper bracket from the sys tem rack af ter the chassis is secur ed.
Installing the BlackDi amond 8800 Series Chassis BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 84 T o ground the chas sis: 1 Locate the grounding point on the back of the chassis ( Fi gur e 48 and Figur e 49 ). Figure 48: Back of BlackDiamond 8806 Chassis Figure 49: Back of BlackDiamond 8810 Chassis 2 S t r i p 0 .
Initial Managem ent Access BlackDiamond 8800 S eries Switches Hardware Installation Guide 85 CAUTION Be sure that no copper is visi ble be tween the lug and the cable insulation. 4 Crimp the lug onto the cable according to the m anufacturer ’s specifications.
Installing the BlackDi amond 8800 Series Chassis BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 86.
BlackDiamond 8800 S eries Switches Hardware Installation Guide 87 6 Installing Power Supply Units in the BlackDiamond 8800 Series Switches This chapter includes the foll owing topics: ● Safety on pa.
Installing Power Supply Unit s in the BlackDiamo nd 8800 Series Switches BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 88 WAR NI NG ! Extreme Networks AC PSUs do not have switches for turnin g the unit on and off. Remove the wall plug from the electrical outlet to disconnect the power to an Extreme Networks AC PSU.
Power Supply Cords for AC Po wer Supplies BlackDiamond 8800 S eries Switches Hardware Installation Guide 89 T o avoid causing an I/O module to be powered off, do not add a 600/900 W AC PSU to an existing BlackDiamond 8806 system running in the configuration listed above.
Installing Power Supply Unit s in the BlackDiamo nd 8800 Series Switches BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 90 ● T h e p o w e r s u p p l y c o r d m u s t b e l e s s t h a n 5 m e t e r s l o n g . ● The wire size must be a minimum of 16 A WG (1.
Installing an Extreme Networks AC PSU BlackDiamond 8800 S eries Switches Hardware Installation Guide 91 Required T ools and Equipment Y ou need the following tools and equipment to install or remove a.
Installing Power Supply Unit s in the BlackDiamo nd 8800 Series Switches BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 92 Figure 51: Inserting an AC PSU into the Power Supply Bay 4 Secure the AC PSU in the power supply bay by pu shing down on the lockin g handle until it clicks into place.
Installing an Extreme Networks AC PSU BlackDiamond 8800 S eries Switches Hardware Installation Guide 93 2 For the AC power cor d: ● If you are replacing only the power supply and you w ill use the existing AC power cord for the n e w P S U , y o u d o n o t n e e d t o u n p l u g t h e A C p o w e r c o r d .
Installing Power Supply Unit s in the BlackDiamo nd 8800 Series Switches BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 94 Installing an Extreme Networks 1200 W DC PSU The Extreme Net.
Installing an Extreme Networks 1200 W DC PSU BlackDiamond 8800 S eries Switches Hardware Installation Guide 95 Each 1200 W DC PSU must be powered by a 50 A dedi cated power source that delivers -40 to -72 VDC of constant power . Power distribution to the 12 00 W DC PSU shall be pr ovided using the -48 VDC harness provided.
Installing Power Supply Unit s in the BlackDiamo nd 8800 Series Switches BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 96 Figure 53: Locking Handle on the 1200 W DC PSU 3 Carefully slide the 1200 W DC PSU all the way into the power supply bay ( see Figur e 5 4 ).
Installing an Extreme Networks 1200 W DC PSU BlackDiamond 8800 S eries Switches Hardware Installation Guide 97 5 Connect the input DC cable to the front of the 1200 W DC PSU a s shown in Figure 55 . NOTE An AC power cord is not required fo r prope r functio ning of the DC PSU.
Installing Power Supply Unit s in the BlackDiamo nd 8800 Series Switches BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 98 NOTE Leave the ESD strap permanently connected to the switch, so that the strap is always availa ble when you need to handle ESD-sensitive components.
Installing an Extreme Networks 1200 W DC PSU BlackDiamond 8800 S eries Switches Hardware Installation Guide 99 NOTE Leave the ESD strap permanently connected to the switch, so that the strap is always availa ble when you need to handle ESD-sensitive components.
Installing Power Supply Unit s in the BlackDiamo nd 8800 Series Switches BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 100.
BlackDiamond 8800 S eries Switches Hardware Installation Guide 101 7 Installing Modules and Establishing Initial Management Access The chapter describes how to install the MSMs an d I/O modules in the BlackDiamond 8800 series switches and how to set up initial management access for the switch.
Installing Modul es and Establishing Initial Manag ement Access BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 102 NOTE The following slots will only operate an MSM: Slot 5/A in the Black Diamond 8810 chassis; slot 3/A in the BlackDiamond 8806 chassis.
Installing a Bla ckDiamond 8800 Series M odule BlackDiamond 8800 S eries Switches Hardware Installation Guide 103 When you handle modules, optic devices, or othe r modular accessories, use an ESD-pr eventive wrist strap to reduce the risk of electr onic damage to the equipment.
Installing Modul es and Establishing Initial Manag ement Access BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 104 Figure 58: Injector/ejector Handles in an Open Position 6 Keep the injector/ejector handles in the open position as you slide the module into the chassis slot.
Installing a Bla ckDiamond 8800 Series M odule BlackDiamond 8800 S eries Switches Hardware Installation Guide 105 ● If the captive screw on each handle has a yellow b a n d a r o u n d t h e h e a d o f t h e s c r e w , t u r n t h e screw on each injector/ejector handle clockwise and completely down.
Installing Modul es and Establishing Initial Manag ement Access BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 106 Making Network Interface Cable Connections Use the appropriate type of cable to connect the ports of your switch to another switch or r outer .
Making Network Interface Ca ble Connections BlackDiamond 8800 S eries Switches Hardware Installation Guide 107 Figure 62: Connecting a 10G4Ca Module Port T o disconnect a cable from a 10G4Ca module: 1.
Installing Modul es and Establishing Initial Manag ement Access BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 108 Installing a Backup MSM If you install a backup MSM, us e the synchronize command to replicate all saved images and configurations fr om the primary MSM to the backup MSM.
Removing a BlackDia mond 8800 Series Modu le BlackDiamond 8800 S eries Switches Hardware Installation Guide 109 Removing a BlackDiamond 8800 Series Module CAUTION There are two styles of ejector/injector handles on the Bl ackDiamond 8800 series m odule s.
Installing Modul es and Establishing Initial Manag ement Access BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 110 Figure 65: Indic ations that the Modu le is Unlocked 3 Squeeze the r.
Blank Front Panels BlackDiamond 8800 S eries Switches Hardware Installation Guide 111 Installing a Blank Front Panel T o install t he blank front panel: 1 Attach the ESD-preventive wrist strap to your bare wrist and connect the metal end to the ground receptacle at the top left corn er of the BlackDiamond chassis.
Installing Modul es and Establishing Initial Manag ement Access BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 112 Figure 67: Captive Screw on a BlackDiam ond 8800 Series Blank Front Panel 3 Remove the blank front panel fr om the fr ont of the BlackDiamond switch (see Figur e 68 ).
Installing or R emoving an Ext ernal Compact Fla sh Memory Car d BlackDiamond 8800 S eries Switches Hardware Installation Guide 113 Installing or Removing an External Compact Flash Memory Card Y o u d.
Installing Modul es and Establishing Initial Manag ement Access BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 114 Initial Management Access After your switch has complete d all power on self-tes ts, it is operational. Y ou can log in and configur e an IP address for the default VLAN (named default ).
Initial Managem ent Access BlackDiamond 8800 S eries Switches Hardware Installation Guide 115 5 At the password pr ompt, pr ess [Return]. The default user name admin has no password assigned to it.
Installing Modul es and Establishing Initial Manag ement Access BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 116.
3 Installing BlackDiamond Switch Accessories.
.
BlackDiamond 8800 S eries Switches Hardware Installation Guide 119 8 Installing BlackDiamond 8800 Series Module Options This chapter includes the foll owing sections: ● I n s t a l l i n g a n S - P.
Installing Black Diamond 8800 Series Mod ule Options BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 120 Figure 70: Daughter Card Connectors on the BlackDiamond G48T c or G48T e2 I/O Module 4 Remove the S-POE card fr om its anti-static packaging.
Removing an S-POE Card BlackDiamond 8800 S eries Switches Hardware Installation Guide 121 6 Align and finger-tighten the r etaining scr ews , st arting with the two middle screw s (see Figur e 72 ) Fi.
Installing Black Diamond 8800 Series Mod ule Options BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 122 Installing an Option Card in the MSM-48c The MSM-48c has a slot for one of the .
Installing an Option C ard in the M SM-48c BlackDiamond 8800 S eries Switches Hardware Installation Guide 123 Figure 74: Inserting the Option Card 6 Release the hot-swap prevention latch and verify that the option car d has engaged the alignment pins and connector at the back of the card.
Installing Black Diamond 8800 Series Mod ule Options BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 124 Removing an MSM Option Card T o remove an option card fr om an MSM-48c module: 1 Attach an ESD-preventive wrist strap to your ba re wrist.
BlackDiamond 8800 S eries Switches Hardware Installation Guide 125 9 BlackDiamond AC Power Cord Retaining Brackets The AC power cord r etaining brackets for BlackDi a mond switches hold the power connectors in the power sockets and prevent accidental disconn ect ion due to earthquakes, vibration, or other di s tu rb a nc e s.
BlackDiamond AC Po wer Cord Retaining Bracke ts BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 126 3 Connect each AC power cord to a power outlet on the BlackDiamond 8810 switch as shown in Figur e 78 .
BlackDiamond 8810 AC Powe r Cord Retaining Bracket BlackDiamond 8800 S eries Switches Hardware Installation Guide 127 6 T ighten the captive screws in the middle and on each end of the power cord retainin g bracket (see Figur e 81 ).
BlackDiamond AC Po wer Cord Retaining Bracke ts BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 128 BlackDiamond 8806 AC Power Cord Retainer Channel Connect all AC power cords befor e you in stall the power cord r etaining bracket.
BlackDiamond 8806 AC Power Cord Retain er Channel BlackDiamond 8800 S eries Switches Hardware Installation Guide 129 3 Hold the AC power cord re tainer channel as shown in Figure 83 . Figure 83: BlackDiamond 8806 AC Po wer Cord Retainer Channel 4 Place the r eta iner channe l against the switch as shown in Figure 84 .
BlackDiamond AC Po wer Cord Retaining Bracke ts BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 130 Figure 85: Routing the Power Cords in the Channel NOTE Leave the ESD-preventive wrist strap permanently connected to the switch, so that the strap is always available when you need to handle ESD-sensitive components.
BlackDiamond 8800 S eries Switches Hardware Installation Guide 131 10 BlackDiamond Cable Management This chapter includes the foll owing sections: ● About BlackDiamond Cable Management on page 131 .
BlackDiamond Cab le Management BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 132 Figure 86: Black Diamond cable hold ers and clips Connecting Cable Holders Each cable holder holds up to 12 separate cables, wi th 6 on each side. Connect cable holders end to end as needed to accommodate the number of cables you need to or ganize.
Using the Cable Holders and Cab le Clips BlackDiamond 8800 S eries Switches Hardware Installation Guide 133 2 Slide the ends together and push the cable holders together until you feel them snap into place (see Figur e 88 ). Figure 8 8: Connected cable holders 3 Connect as many cable holders together as you need to manage your cable bundles.
BlackDiamond Cab le Management BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 134 3 Press the clips together until l the connectors lock into place (see Figure 90 ). Figure 90: Cable clip chain 4 Connect as many cable clips together as you need to manage your cable bundles.
BlackDiamond 8800 S eries Switches Hardware Installation Guide 135 4 BlackDiamond Maintenance Procedures.
BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 136.
BlackDiamond 8800 S eries Switches Hardware Installation Guide 137 11 Replacing BlackDiamond 8800 Series Chassis Components This chapter pr ovides instructi ons for repl acing components in the BlackD.
Replacing BlackDiamo nd 8800 Series Chassis Com ponents BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 138 Figure 91: Rem oving the Fan T ray from the BlackDiamond 8810 Swit ch Figure 92: Rem oving the Fan T ray from the BlackDiamond 8806 Swit ch 4 Use the fan tray handle to pull the fan tray ha lf-way out from the fan tray slot.
Replacing the Fa n Tray BlackDiamond 8800 S eries Switches Hardware Installation Guide 139 CAUTION Be sure that both hands are us ed to suppo rt the weight of the fan tray during removal. NOTE Leave the ESD-preventive wrist strap permanently connected to the switch so that it is always available when you need to touch ESD-sensitive components.
Replacing BlackDiamo nd 8800 Series Chassis Com ponents BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 140 Figure 94: Installing the Fan T ray in the BlackDiamond 8806 Switch 3 Use a #2 Phillips scr ewdriver to tighten the scr ews ( Figure 93 ).
Replacing the PSU/ Fan Controller BlackDiamond 8800 S eries Switches Hardware Installation Guide 141 Removing the PSU/Fan Controller T o remove a PSU/fan controller fr om the BlackDiamond 8800 series .
Replacing BlackDiamo nd 8800 Series Chassis Com ponents BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 142 Figure 96: Removing the Access Cove r from the BlackDiamond 8806 Switch 3 Using a #2 Phillips scr ewdriver , loosen all eight captive scr ews on the PSU/f an contr oller access cover .
Replacing the PSU/ Fan Controller BlackDiamond 8800 S eries Switches Hardware Installation Guide 143 6 Using a #1 Phillips scr ewdrive r , loosen all four c aptive screws on the PSU/fan contr oller . 7 Pull equally on the u pper and lower handles of the PSU/fan controller to disconnect the contr oller connector .
Replacing BlackDiamo nd 8800 Series Chassis Com ponents BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 144.
BlackDiamond 8800 S eries Switches Hardware Installation Guide 145 12 Repacking a BlackDiamond 8800 Series Chassis This chapter includes the foll owing sections: ● Safety Information on page 145 ●.
Repacking a Bl ackDiamond 8800 Series Chassi s BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 146 ● Four rack-mount screws appropriate to your organization’s equipment rack ● Sc.
Repacking the BlackDia mond 8810 Chassis BlackDiamond 8800 S eries Switches Hardware Installation Guide 147 Figure 98: Correct Method for Liftin g the BlackDiamond 8810 C hassis ASP017A.
Repacking a Bl ackDiamond 8800 Series Chassi s BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 148 8 Attach all four restraining bolts to the four sh ipping brackets, securing the BlackDiamond 8810 chassis to the shippi ng pallet (se e Figure 99 ).
Repacking the BlackDia mond 8810 Chassis BlackDiamond 8800 S eries Switches Hardware Installation Guide 149 11 Place the packing foam on top of the BlackDiamond 8810 chassis (see Figure 101 ). Figure 101: Packing Foam in the Bl ackDiamond 8810 Shipping Carton 12 Close the top flaps on the shipping carton and seal them with packing tape.
Repacking a Bl ackDiamond 8800 Series Chassi s BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 150 Repacking the BlackDiamond 8806 Chassis T o repack the BlackDiamond 8806 chassis: 1 Attach the ESD-preventive wrist strap to your bare wrist and connect the metal end to the ground receptacl e on the chassis fr ont panel.
Repacking the BlackDia mond 8806 Chassis BlackDiamond 8800 S eries Switches Hardware Installation Guide 151 8 Slide the top of the BlackDiamond shipping cart on down and over the BlackDiamond 8806 chassis (see Figure 104 ). Figure 104: Placing the Carton over the BlackDiamond 8806 Chassis 9 Insert the clip locks (see Figur e 105 ).
Repacking a Bl ackDiamond 8800 Series Chassi s BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 152 10 Place the packing foam material on top of the chassis as shown in Figure 106 .
5 Appendixes.
.
BlackDiamond 8800 S eries Switches Hardware Installation Guide 155 A Safety Information WAR NI NG ! Read the following safety information th oroughly before installing Extreme Netw orks products. Failure to follow this safety information can lead to personal injury or damage to the equipment.
Safety Infor mation BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 156 WAR NI NG ! Be sure that the requirements liste d in this section are satisfied when installing all Extreme Networks power supplies.
General Safety Precautions BlackDiamond 8800 S eries Switches Hardware Installation Guide 157 ● Disconnect all power before r emoving the back panel of any Extr eme Networks sw itch, unless otherwise instructed by a pr oduct specific maintenance pr ocedure.
Safety Infor mation BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 158 PoE Devices When connecting power over Ethernet (PoE) devices to a PoE switch, all connections between the PoE device and the switch must r emain inside the same building and use a low-voltage powe r distribution system per IEEE 802.
Battery Replacement and Dispo sal BlackDiamond 8800 S eries Switches Hardware Installation Guide 159 The following countries have specific safety instr uctions concerning power connectors: ● A r g e n t i n a : T h e s u p p l y p l u g m u s t c o m p l y w i t h A r g e n t i n e a n s t a n d a r d s .
Safety Infor mation BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 160 WAR NI NG ! Laser optic modules become very hot after prolonged use.
Fiber Optic Ports— Optical Saf ety BlackDiamond 8800 S eries Switches Hardware Installation Guide 161 Sicherheitshinweise V or der Installation der Produkte von Extreme Networks sind die nachfolgenden Sicher heitshinweise aufmerksam zu lesen.
Safety Infor mation BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 162 Installation von Netzteilen Bei der Installation sämtlicher Netzteile von Extre me Netw orks muss sichergestellt we rden, dass die nachfolgend aufgeführten Anforderungen erfüllt si nd.
Fiber Optic Ports— Optical Saf ety BlackDiamond 8800 S eries Switches Hardware Installation Guide 163 W artungssicherheit Folgende V orsichtsmaßnahmen müssen getr of fen wer den: ● Nur für den Einsatz mit dies em System zugelassene Originalzubehörteile bzw .
Safety Infor mation BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 164 V er einigten Staaten und Kanada wer den normalerwe ise von einem Drittanbieter geliefert und müssen die folgenden Anforder ungen erfüllen: ● Die Stromkabel müssen of fiziell fü r das Land zugelass en sein, in dem sie verwendet wer den solle n.
Fiber Optic Ports— Optical Saf ety BlackDiamond 8800 S eries Switches Hardware Installation Guide 165 Hinweis: Die Bauvorschriften sind weltweit ve rschieden; Extreme Networks empfiehlt daher ausdr.
Safety Infor mation BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 166.
BlackDiamond 8800 S eries Switches Hardware Installation Guide 167 B T echnical Specifications This appendix includes the fol lowing technical specifications : ● BlackDiamond 8810 Switch on page 167.
Technical Specific ations BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 168 EMI/EMC Standards North America EMC for ITE FCC CFR 47 part 15 Class A (USA ) ICES-003 Class A (Canada) Eu.
BlackDiamond 8810 Switch BlackDiamond 8800 S eries Switches Hardware Installation Guide 169 Acoustic Sound ( BlackDiamond 88 10 Switch with AC Power Supplies) Sound power in accordance with EN 300 753 (10-19 97) Sound power Normal: 70 dBA per ISO 7779 High: 75 dBA per ISO 7779 Declared sound power Normal: 7.
Technical Specific ations BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 170 BlackDiamond 8806 Switch T able 20: BlackDiamond 8806 sw itch T echnical Specifications Physical Dimensions BlackDiamond 8806 chassis Height: 17.47 inches (4 4.
BlackDiamond 8806 Switch BlackDiamond 8800 S eries Switches Hardware Installation Guide 171 Country-specific VCCI Class A (Japan Emissions) AS/NZS 3548 ACA (Austral ia Emissions) CNS 13438: 1997 Class.
Technical Specific ations BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 172 Power Supplies for BlackDiamond 8800 Series Switches T able 21: Specifications for the AC SSI PS Model #60.
Connector Pinouts BlackDiamond 8800 S eries Switches Hardware Installation Guide 173 Connector Pinouts Ta b l e 2 4 describes the pinouts for a DB-9 console plug connector .
Technical Specific ations BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 174 Figure 108 shows the pinout s for a 9-pin to 25-pin (RS-232) nu ll-modem cable. Figure 108: Null-modem Cable Pinouts Figure 109 shows the pinouts for a 9-pin to 9- pin (PC-A T) null-modem serial cable.
BlackDiamond 8800 S eries Switches Hardware Installation Guide 1 Index Numerics 10G4Ca I/O module, 31 10G4X I/O modul e, 26 10G4Xa I/O module, 31 10G4Xc I/O module, 33 10G8Xc I/O module, 34 1200 W DC .
Index BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 2 C cable connections, making , 106 cable identification records, 61 cable labe ling identificati on, 61 recommendations, 61 recor.
Index BlackDiamond 8800 S eries Switches Hardware Installation Guide 3 full-duplex, 16 G G24X I/O module, 26 G24Xc I/O module, 34 G48P I/O module, 28 G48Pe I/O module, 37 G48T I/O module, 27 G48Ta I/O.
Index BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 4 mid-mount instal lation. See rack installation mounting ho les, rack, 58 MSM available slots, 102 booting, 22 console port, 23 d.
Index BlackDiamond 8800 S eries Switches Hardware Installation Guide 5 S-G8Xc option card, 23, 122 shipping indicators BlackDiamond 8810 shock watch, 75 tilt watch, 75 good state, 75 red state, 75 war.
Index BlackDiamond 8800 S eries Switches Hardware Inst allation Guide 6.
An important point after buying a device Extreme Networks BlackDiamond 8800 Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Extreme Networks BlackDiamond 8800 Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Extreme Networks BlackDiamond 8800 Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Extreme Networks BlackDiamond 8800 Series you will learn all the available features of the product, as well as information on its operation. The information that you get Extreme Networks BlackDiamond 8800 Series will certainly help you make a decision on the purchase.
If you already are a holder of Extreme Networks BlackDiamond 8800 Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Extreme Networks BlackDiamond 8800 Series.
However, one of the most important roles played by the user manual is to help in solving problems with Extreme Networks BlackDiamond 8800 Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Extreme Networks BlackDiamond 8800 Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
