Instruction/ maintenance manual of the product XP Exmark
Go to page of 24
UL TRA V AC ® LAZER Z ® , LAZER Z ® AS, LAZER Z ® XP AND LAZER Z ® XS MODELS For Ultra V ac Serial Nos. 850,000 & Higher (to t Lazer Z (LZ), Lazer Z AS (LAS), and Lazer Z XP Units 352,000–789,999) (to t Lazer Z XS Units 352,000 & Higher) Part No.
Exmark reser ves the right to make changes or add improv ements to its products at an y time without incurring any obligation to make such changes to products man ufactured previousl y .
Introduction CONGRATULATIONS on the purchase of your Exmark Ultra V ac. This product has been carefully designed and man ufactured to gi ve y ou a maxim um amount of dependability and years of trouble-free operation.
Contents Introduction . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . . . 3 Safety .. . . . . . . . . .. . . . . . . . . . .. .. . . .. .. . . .. .. . . .. . . . . . . . . . . .. . . . . . . .
Safety Safety Safety Alert Symbol This Safety Alert Symbol (Figure 2) is used both in this man ual and on the mac hine to identify important safety messages which m ust be follow ed to av oid accidents This symbol means: ATTENTION! BECOME ALERT! Y OUR SAFETY IS INV OL VED! Figure 2 1.
Safety collection system or mulch kit in place and w orking properly . DANGER There are rotating blades in the blo wer and under the mow er deck. Blade contact can cause serious operator or bystander injur y or ev en death. • Do Not reach into blo wer unless rotation indicator has stopped.
Safety Figure 3 1. Safe Zone-Use the mower here on slopes less than 15 degrees 2. Danger Zone-Use a walk behind mower and/or hand trimmer on slopes greater than 15 degrees, near drop-offs and water . 3. Water • Remo v e or mark obstacles such as roc ks , tree limbs , etc.
Safety Safety and Instructional Decals • Keep all safety signs legible. R emov e all grease, dirt and debris from safety signs and instr uctional labels . • Replace all w orn, damag ed, or missing safety signs . • When replacement components are installed, be sure that current safety signs are afx ed to the replaced components .
Safety 103-3508 LZUV52 Only 109-5890 UV60 and UV6672 9.
Specications Specications Model Numbers Serial Nos: 850,000 and Higher LZUV52–Fits Lazer Z (LZ) and Lazer Z AS (LAS) Units 789,999 and Lo wer with 52 inch dec k. UV60–Fits Lazer Z (LZ), Lazer Z AS (LAS), and Lazer Z XP Units 352,000–789,999 and Lazer Z XS Units 352,000 and Higher with 60 inch deck.
Specications Overall Length: w/Ultra V ac 52 inch Deck-Air -Cooled 105.70 inches (268.5 cm) 52 inch Dec k- Liquid-Cooled 106.00 inches (269.1 cm) 60 inc h Dec k-SN 599,999 and Low er Air -Cooled 106.65 inches (270.9 cm) 60 inch Dec k-SN 600,000–789,999 Air-Cooled 110.
Operation Product Overview Figure 4 1. Hood 4. Tube 2. Weight 5. Bag 3. Blower Operation Note: Deter mine the left and right sides of the machine from the nor mal operating position. Pre-Start Make sure you understand the controls , their locations , their functions , and their safety requirements .
Operation hav e stopped before clearing blow er assembly or mow er dec k 3. T o remo v e the bags , rst shut off dec k dri ve , stop the engine and wait for all moving parts to stop . Open the hood and remov e the bags b y lifting up on the rear of the bag, then unhooking the front clip .
Operation Figure 6 Viewed from the right side 1. Hairpin 3. Discharge Chute 2. Chute Pivot Pin Note: Install chute with the tabs to the rear of the deck tabs as sho wn. W ARNING An unco v ered discharge opening will allow objects to be thrown in operator’s or bystander’s direction.
Operation 6. Pull the spring loaded idler bac k and slip the belt ov er the top spindle deck sheav e . 7. Install the plastic belt cov er . On 60 inc h and 66 inch units the outside end of the cov er is slotted and can slip betw een the tw o washers on the belt shield stud.
Operation T ransporting T ransporting a Unit Use a hea vy-duty trailer or truck to transport the machine . Loc k brak e and block wheels . Securely fasten the machine to the trailer or tr uck with straps , chains , cable , or ropes . Be sure that the trailer or tr uc k has all necessar y lighting and marking as required by law .
Operation minimize the ramp angle . The trailer or truck should be as lev el as possible . Important: Do Not attempt to tur n the unit while on the ramp , y ou may lose control and driv e off the side. A v oid sudden acceleration when driving up a ramp and sudden deceleration when backing do wn a ramp .
Maintenance Maintenance Note: Deter mine the left and right sides of the mac hine from the nor mal operating position. W ARNING While maintenance or adjustments are being made, someone could star t the engine. Accidental star ting of the engine could seriously injure y ou or other bystanders.
Maintenance Lubricate Grease Fittings Note: See char t for ser vice inter v als. 1. Stop engine , w ait for all moving parts to stop , and remov e key . Engage parking brake . 2. Lubricate ttings with NGLI g rade #2 multi-purpose gun grease. R efer to the following chart for tting locations and lubrication sc hedule.
Maintenance Cleaning Clean Mufer and Rear Frame Area Service Interval: Before each use or daily Stop engine, wait for all moving parts to stop , and remov e key . Engag e parking brak e. W ARNING Operating engine parts, especiall y the mufer, become extremely hot.
T roubleshooting T roubleshooting Important: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to mow er use. When a problem occurs , Do Not o verlook the simple causes . F or example: starting problems could be caused b y an empty fuel tank.
Conditions and Products Co vered Exmark Mfg. Co. Inc. and its aff iliate, Exmark W arranty Company , pursuant to an agreement between them, jointly warrant on the terms and conditions herein, that we .
G01 1841 Figure 10 This page may be copied for personal use. 1. The maximum slope you can safely operate the machine on is 15 degrees . Use the slope indicator to determine the degree of slope of hills before operating. Do Not operate this machine on a slope greater than 15 degrees.
MID-MOUNT RIDING A CCESSORIES AND OPTIONS SEE EXMARK’S COMPLETE LINE OF A CCESSORIES AND OPTIONS W ALK-BEHIND A CCESSORIES AND OPTIONS GRASS CA TCHER MICRO-MULCH SYSTEM TURF STRIPER ST ANDON CUST OM.
An important point after buying a device Exmark XP (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Exmark XP yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Exmark XP - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Exmark XP you will learn all the available features of the product, as well as information on its operation. The information that you get Exmark XP will certainly help you make a decision on the purchase.
If you already are a holder of Exmark XP, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Exmark XP.
However, one of the most important roles played by the user manual is to help in solving problems with Exmark XP. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Exmark XP along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
