Instruction/ maintenance manual of the product OCDWB01 Exmark
Go to page of 20
OCDWB01 OPERA TOR CONTROLLED DISCHARGE FOR W ALK-BEHIND UNITS Part No. 4500-569 Rev . A.
Exmark reser ves the right to make changes or add improv ements to its products at an y time without incurring any obligation to make such changes to products man ufactured previousl y .
Introduction CONGRATULATIONS on the purchase of your Exmark equipment. This product has been carefully designed and man ufactured to gi ve y ou a maxim um amount of dependability and years of trouble-free operation. This man ual contains operating, maintenance , adjustment, and safety instr uctions for y our Exmark equipment.
Contents Introduction . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . . . 3 Safety . . .. . . . . . . . . . .. .. . . .. .. . . .. .. . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . .
Safety Safety Safety Alert Symbol This Safety Alert Symbol (Figure 1) is used both in this man ual and on the mac hine to identify important safety messages which m ust be follow ed to av oid accidents This symbol means: ATTENTION! BECOME ALERT! Y OUR SAFETY IS INV OL VED! Figure 1 1.
Safety collection system or m ulch kit in place and w orking properly . • Stop engine, wait for all mo ving parts to stop , remov e key and engag e parking brake: – Before c hecking, cleaning or w orking on the mow er .
Safety Safety and Instructional Decals • Keep all safety signs legible . R emo ve all grease, dirt and debris from safety signs and instr uctional labels . • R eplace all w orn, damag ed, or missing safety signs . • When replacement components are installed, be sure that current safety signs are afx ed to the replaced components .
Setup Setup Assembling Discharge Deector to OCDWB01 Insert the rod through the rst tab on the gate link frame, disc harge deector , and second tab on the gate link frame (Figure 2). Orient and install the spring so that the loop will rest in the notch on the disc harge deector .
Setup Figure 5 1. Latch 3. Front pin 2. OCDWB01 assembly 4. Slot • If the front pin does not engag e in the slot in the deck, loosen or completely remov e the hardware in the g ate link frame as shown in Figure 6. P osition the g ate link frame so that the front pin aligns with the slot.
Setup there will be room to tighten the n ut on the upper hole, on the underside of the front panel. C. Drill tw o 11/32 inc h diameter holes on the front panel as sho wn in Figure 7. D . Align the tw o holes in the mounting brack et with the front panel of the unit.
Setup B . Align the existing hole at the rear of the unit with the right hole on the brac ket. C. P osition the brac ket horizontally or with the narrow end pointed slightly downw ard. D . Using the mounting brac ket as a template , mark the left hole location onto the side panel of the unit and drill 11/32 inc h diameter hole (see Figure 11).
Product Overview Figure 14 1. V elcro strap 2. Loom clip Product Overview Figure 15 1. Handle 2. Discharge gate (under discharge deector) 3. Discharge deector 12.
Operation Operation Use the discharge gate to temporarily stop or deect g rass clippings aw ay from sidew alks , parking lots , patios , or anywhere grass clippings are not desired to be discharged. The handle allo ws the discharge gate to be held in any position from fully closed to fully open.
Operation Closing the Discharge Gate F or all W alk-Behind Units ex cept V antage: Push down on the handle to close the gate. Figure 18 1. Push down 2. Handle in gate closed position F or V anta ge Units: Push forw ard on the handle to close the gate.
Operation Figure 21 1. Handle assembly 3. Clevis pin 2. Mounting bracket 4. Hairpin 4. Unloc k the assembly and pi v ot it aw ay from the mow er deck. Lift the OCD WB01 out of the dec k mounting tube .
Maintenance Maintenance Note: Deter mine the left and right sides of the machine from the normal operating position. W ARNING While maintenance or adjustments are being made, someone could star t the engine. Accidental star ting of the engine could seriously injure y ou or other bystanders.
Maintenance Figure 22 1. Pivot bolt and nut Discharge Gate Adjustment The disc harge gate is properly adjusted in the closed position when the discharge gate is at ag ainst the discharge opening . If the disc harge gate does not close at follo w the steps below: 1.
T roubleshooting T roubleshooting Important: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to mow er use. The following table lists some of the common causes of trouble . If assistance is needed, contact y our Exmark Ser vice Dealer .
Conditions and Products Co vered Exmark Mfg. Co. Inc. and its aff iliate, Exmark W arranty Company , pursuant to an agreement between them, jointly warrant on the terms and conditions herein, that we .
MID-MOUNT RIDING A CCESSORIES AND OPTIONS SEE EXMARK’S COMPLETE LINE OF A CCESSORIES AND OPTIONS W ALK-BEHIND A CCESSORIES AND OPTIONS GRASS CA TCHER MICRO-MULCH SYSTEM TURF STRIPER ST ANDON CUST OM.
An important point after buying a device Exmark OCDWB01 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Exmark OCDWB01 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Exmark OCDWB01 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Exmark OCDWB01 you will learn all the available features of the product, as well as information on its operation. The information that you get Exmark OCDWB01 will certainly help you make a decision on the purchase.
If you already are a holder of Exmark OCDWB01, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Exmark OCDWB01.
However, one of the most important roles played by the user manual is to help in solving problems with Exmark OCDWB01. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Exmark OCDWB01 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
