Instruction/ maintenance manual of the product 007-3086-001 Exabyte
Go to page of 42
8505XL 8-mm T ape Drive Owner ’s Guide Document Number 007-3086-001.
8505XL 8-mm T ape Drive Owner ’s Guide Document Number 007-3086-001 CONTRIBUTORS W ritten by Pablo Rozal Illustrated by Dan Y oung and Cheri Br own Edited by Christina Cary Production by Derrald V o.
iii Contents List of Figures v List of T ables vii About This Guide ix Typographical Conventions x 1. Installation 1 Products that Support the 8505XL 1 Preparing for Installation 2 Ensuring ESD Protec.
iv Contents 2. Operating the T ape Drive 17 Reading the LEDs 17 Selecting Data Cartridges 19 Write-Protecting a Data Cartridge 20 Loading a Data Cartridge 20 Unloading a Data Cartridge 21 Resetting the Tape Drive 21 3.
v List of Figur es Figure 1-1 Removing/Installing the Drive From/On the Drive Sled 5 Figure 1-2 Setting the SCSI ID (Default Setting Shown) 6 Figure 1-3 Setting the Drive Sled for Single-Ended Operati.
vi.
vii List of Tables T able 1-1 Problems and Possible Solutions 15 T able 2-1 LED States and Interpretations 18 T able 2-2 8505XL Tape Capacity 19 T able A-1 Drive Specifications 31.
viii.
ix About This Guide This guide helps you set up, install, and operate the 8505XL tape drive. The 8505XL uses 8-mm format tapes and installs in most of the existing Silicon Graphics© systems and data storage units that support single-ended, front-loading drives (FLDs).
x About This Guide T ypographical Conventions These type conventions and symbols ar e used throughout this guide: Italics Filenames, variables, IRIX ® command ar guments, command fl ags, titles of publications, icon names. Screen type Code examples, fi le excerpts, and scr een displays (including error messages).
1 Chapter 1 1. Installation This chapter provides information for the following tasks: • preparing for installation • installing the tape drive • installing the software driver Note: The 8505XL requir es either IRIX 5.3, 6.1 or later software. If your system already has IRIX 6.
2 Chapter 1: Installation Preparing for Installation T o prepar e for installation, follow the steps described in this chapter . 1. Ensure ESD pr otection (see “ Ensuring ESD Protection ” on page 2). 2. Unpack the tape drive and save the packing materials (see “ Unpacking the T ape Drive and Saving the Materials ” on page 3).
Installing the Tape Drive 3 Unpacking the T ape Drive and Saving the Materials Carefully r emove the tape drive from its box. Save all the original packaging materials in case you need to reship the tape drive. The tape drive ’ s packaging helps protect the tape drive fr om shock, vibration, moisture, and electrostatic dischar ge (ESD).
4 Chapter 1: Installation Before setting the tape drive ’ s SCSI ID, determine the SCSI IDs of all the other SCSI devices currently attached to your bus (for example, a har d drive or a CD-ROM reader). Caution: SCSI ID 0 is reserved for the system contr oller and cannot be used.
Installing the Tape Drive 5 1. Remove the four screws that secur e the drive to the bottom of the mounting sled (see Figure 1-1) and set them aside. Figure 1-1 Removing/Installing the Drive Fr om/On the Drive Sled 2. Remove the drive adapter and power cables fr om the 8505XL (see Figure 1-1) and then place the drive on an anti-static surface.
6 Chapter 1: Installation Figure 1-2 Setting the SCSI ID (Default Setting Shown) 4. Using a pair of fl at-nose pliers, slide the small plastic jumpers over the pins on the jumper block to obtain the desir ed address. Extra jumpers are shipped in a separate bag.
Installing the Tape Drive 7 7. Install the four screws that secur e the bottom of the drive to the drive sled (see Figure 1-1). Configuring the Drive Sled for Single-Ended Operation The 8505XL drive sled assembly houses a SCSI channel adapter boar d.
8 Chapter 1: Installation Figure 1-3 Setting the Drive Sled for Single-Ended Operation Note: Y our system disk should always be set to SCSI ID 1. Be sur e each SCSI device on a bus has a unique SCSI addr ess (ID). The SCSI bus cannot function properly if mor e than one device has the same SCSI ID.
Installing the Tape Drive 9 Follow these instructions to install a half-height fr ont-loading device: Installing Into a Horizontal Drive Bay Follow these instructions to install the drive into a horizontal drive bay .
10 Chapter 1: Installation Figure 1-4 Installing the T ape Drive Into a Horizontal Drive Bay Slide drive lever left to lock sled Drive lever in locked position.
Installing the Tape Drive 11 Figure 1-5 Installing the T ape Drive Into a V ertical Drive Bay Drive sled Drive.
12 Chapter 1: Installation T urning On Power to the T ape Drive When power is applied to the 8505XL, watch for the following: • All three of the tape drive ’ s LEDs light.
Installing the Tape Drive 13 1. Locate a data cartridge that does not contain any valuable information and make sure that its write-pr otect switch is set to write-enable (see Figure 1-6). 2. Gently push the data cartridge as shown (in Figur e 1-7) until the load mechanism pulls the cartridge into the drive.
14 Chapter 1: Installation Figure 1-7 Loading a Data Cartridge 3. W ait while the tape drive loads the tape, determines the tape format, and positions the tape to the logical beginning of the tape (LBOT). This takes about 45 seconds. When the gr een LED is on solid, the tape drive is ready .
Installing the Tape Drive 15 4. Perform a backup operation to write a small amount of data to the tape (see your IRIX administration documentation, as r equired). 5. Rewind the tape and read the data written in step 4 and compar e it to the original. This determines whether the softwar e and tape drive are functioning properly .
16 Chapter 1: Installation.
17 Chapter 2 2. Operating the T ape Drive This section includes information about the following: • reading the tape drive ’ s LEDs • selecting data cartridges • setting the write-protect switc.
18 Chapter 2: Operating the Tape Drive Figure 2-1 8505XL Front Panel Note: Y ou may occasionally observe LED combinations and sequences not described in T able 2-1. These other combinations r epresent special or unusual conditions that are beyond the scope of this table.
Selecting Data Cartridges 19 Note: The LEDs fl ash at differ ent speeds to distinguish between states: • slow fl ash = 1 fl ash/second • fast fl ash = 4 fl ashes/second • Irregular fl ash = rate of fl ash varies with SCSI bus activity . If the device is not connected to the bus, the LED is of f.
20 Chapter 2: Operating the Tape Drive Note: The EXA T APE 160-m XL data cartridges contain a r ecognition system stripe located on the tape leader for media identi fi cation. The 8505XL uses this stripe to distinguish data-quality metal-particle media, such as EXA T APE, from other 160-m media.
Unloading a Data Cartridge 21 Unloading a Data Cartridge The unload button is the only operating contr ol on the tape drive. It is used to unload the data cartridge from the tape drive (see Figur e 2-2). Note: Y ou can use the unload button to clear some har dware err ors.
22 Chapter 2: Operating the Tape Drive.
23 Chapter 3 3. Pr eventive Maintenance The only routine maintenance r equired by the tape drive is r egular cleaning of the tape drive heads and tape path. Pr oper storage and maintenance of your data cartridges maximizes the shelf life of your tapes and assur es data integrity .
24 Chapter 3: Preventive Maintenance Using the Cleaning Cartridge T o use the cleaning cartridge, follow these steps: 1. Make sure that the tape drive is on and has r un the power-on self-test in T able 2-1 in Chapter 2. 2. Remove any data cartridge from the tape drive.
Caring for Data Cartridges 25 Caring for Data Cartridges T o maximize the shelf life of your tapes and assur e data integrity , follow these guidelines when storing data cartridges: • Place a label or other refer ence information on the cartridge adjacent to the write-protect switch.
26 Chapter 3: Preventive Maintenance Replacing Data Cartridges Approximately once each year , you may want to r ead all information on a tape and check the read err or statistics.
27 Chapter 4 4. T r oubleshooting This chapter provides suggestions for solving pr oblems that may occur when you are installing and operating your tape drive.
28 Chapter 4: Troubleshooting Problems With T ape Drive Operation Most problems with tape drive operation occur with impr oper cartridge use. If you have been successfully operating your backup softwa.
Problems With Tape Drive Operation 29 If you are experiencing operating pr oblems loading or unloading a data cartridge, check the following: • Make sure that your system is turned on. If the system is of f, the tape drive may not eject the data cartridge.
30 Chapter 4: Troubleshooting.
31 Appendix A A. T ape Drive Speci fi cations T able A-1 shows the speci fi cations for the 8505XL tape drive. T able A-1 Drive Speci fi cations Parameter Speci fi cations Interface SCSI-1 and SCS.
32 Appendix A: Tape Drive Specifications Power and Reliability Input voltages Standard + 5 VDC and +12 VDC 5% Power consumption 14.5 W Mean time between failur e 160,0000 hours at 10% duty cycle T abl.
An important point after buying a device Exabyte 007-3086-001 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Exabyte 007-3086-001 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Exabyte 007-3086-001 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Exabyte 007-3086-001 you will learn all the available features of the product, as well as information on its operation. The information that you get Exabyte 007-3086-001 will certainly help you make a decision on the purchase.
If you already are a holder of Exabyte 007-3086-001, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Exabyte 007-3086-001.
However, one of the most important roles played by the user manual is to help in solving problems with Exabyte 007-3086-001. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Exabyte 007-3086-001 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
