Instruction/ maintenance manual of the product 227 Evolution Technologies
Go to page of 16
OWNER'S MANUAL DieHard Ev°luti°n Techn°l°gY_" Power for your changing life. Microprocessor Controlled, Fully Automatic Operation Battery Charger with Engine Starter Plus Battery and Alte.
/ q._ :] n =i[o] ;lifo] _ Jill =i _ ill_ "- ] WARRANTY ................................................................................................................ 2 IMPORTANT SAFETY INSTRUCTIONS ..............................................
WARNING - RISK OF EXPLOSIVE GASES WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BAT- TERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE USING YOUR CHARGER, YOU READ THIS MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY.
Never place charger directly above battery being charged. The gases from the battery wilI corrode and damage the charger. Never touch the battery cIamps together when the charger is on. You could cause a spark. Never operate charger if it has received a hard blow, been dropped, or otherwise damaged.
it is important tounderstand your charger's requirements. This section will teII you about your charger's electrical requirements and how toprepare a battery for charging. PLUGGING IT IN Your charger requires a 120V AC 2-prong 'wail outlet receptacle installed according toalI local codes and ordinances.
Io] 14 _.!-'1 t I 1[_]111 f.-'11 _.tl[_,t i [o] 1 f--1 NOTE: A marine (boat) boat battery must be removed and charged on shore. To charge it on board requires equipment specially designed for marine use. IMPORTANT: Follow all safety instructions and precautions when charging your bat- tery.
CHARGING BATTERY REMOVED FROM THE VEHICLE: POSmVE NEGATIVE BATTERY BATTERY CHARGER __POWER CORD TO GROUNDED POWER OUTLET 1. Note the potarity of the battery posts by checking the identification marks on the battery: POSITIVE (POS, P or +) and NEGATIVE (NEG, N or -).
3. Cool Down - After cranking, the char- ger enters amandatory 3-minute (180 second) cool down state. During this period, no settings can be changed. The buttons are ignored. The digital dispIay indicates the remaining cool down time in seconds. It starts at 180 and counts down to 0.
If the charge mode is changed after charg- ing has started (by pressing the CHARGE RATE or BATTERY TYPE button), the charging process will berestarted. The voltage displayed during charging is the charging voltage and usually will be higher than the battery's resting voltage.
71227 CONTROL PANEL GUIDE MODE OF OPERATION Initial power-up, baftery not detected No battery or reversed battery detected Battery tester activated Battep] tester with charged battery Battmy tester wi.
La[_-,) I_ [c]a d- i=m :Lnnj I mi d I _I I :T._i al d =1 z_h"dfi d =[...'.,]u d =1 z_ OVERVIEW This battery charger has a built-in battery tester that displays either an accurate battery voItage or an estimate of the battery's relative charge based on the battery voItage and the Battery Council International scale.
_l[-_i_[Ltl/:l_ :]ljllllHl_|;lill:lz_;_il[O]Z_ id::_"]ld::lZ_ This battery charger has a built-in alter- nator tester that dispIays either an accu- rate alternator voltage or an estimate of the alternator's relative output compared to normal alternators.
This charger adjusts the charging time in order to charge the battery completeIy, efficiently and safeIy. The microproces- sor automatically makes the necessary decisions. However, this section incIudes guideIines that can be used to estimate charging times.
Read this entire manual before using your charger. The tips below serve only as a guide for specific situations. If your vehicle won't start: You don't need to fully charge a battery to star[ your vehicle.
I / P.(l]+lJ :| ! ::_']"[.Iei t I + [_ Performance probtems often can be corrected by the user. Please read through this chart for a possible solution to common problems. PROBLEM POSSIBLE CAUSE SOLUTION The battery is connected The charger is in tester and the charger is on, mode, not charger mode.
This section shows an illustration of your battery charger. Use it to become familiar with part locations and appearance. Replacement Parts List Sears 71227 ITEM DESCRIPTION PART NUMBER 1 HandleAssemb.
An important point after buying a device Evolution Technologies 227 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Evolution Technologies 227 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Evolution Technologies 227 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Evolution Technologies 227 you will learn all the available features of the product, as well as information on its operation. The information that you get Evolution Technologies 227 will certainly help you make a decision on the purchase.
If you already are a holder of Evolution Technologies 227, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Evolution Technologies 227.
However, one of the most important roles played by the user manual is to help in solving problems with Evolution Technologies 227. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Evolution Technologies 227 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
