Instruction/ maintenance manual of the product WorkFit-D, Sit-Stand Desk Ergotron
Go to page of 12
1 of 12 < 65 lbs. (29.5 k g) 888-24-205-G-01 rev . C • 09/12 WorkFit-D.
2 of 12 888-24-205-G-01 rev . C • 09/12 These symbols alert users of a safet y condition that demands atten tion. All users should be able to recogniz e and understand the signi cance of the fol- lowing Safety Hazards if encount ered on the pr oduct or within the documentation.
3 of 12 888-24-205-G-01 rev . C • 09/12 W ARNING! Stop screw s are pre-installed in this produc t to secure it in the compressed position during shipping and installation. DO N OT REMOVE THESE SCREWS UNTIL INSTRUCTED TO DO SO IN THESE INSTRUCTIONS. Ma ke s ur e these scr ews ar e in place before starting installation.
4 of 12 1x 1x # 12-14 W ood Screw M5 x 6 mm M2.9 x 8 mm 17x 2x 3x 3x 16x 2x 1x 1/4” 14mm 1x 888-24-205-G-01 rev . C • 09/12 Components T ools Needed.
5 of 12 F ront =2 screws Middle = 3 screws Rear = 3 screws 8x Fron t Edge of W orksurface Rear Edge of W orksurface # 12-14 W ood Screw Set the right leg (with hand brak e) upright on the worksurface. Partially inser t 3 of the provided #12-14 w ood screw s at the rear of the leg, 3 near the middle of the leg and 2 at the fron t of the leg.
6 of 12 9x NO TE: Do not fully insert the screw s into the work- sur face at this time. L eave appro ximate - ly 1/8” space. # 12-14 W ood Screw 16x M5 x 6 mm 888-24-205-G-01 rev . C • 09/12 6 5 4 Use a Phillips scre wdriv er to inser t the provided M5x6 mm scr ew s into the two crossbars connecting the left and right legs.
7 of 12 3x 3x M2.9 x 8 mm 2x 888-24-205-G-01 rev . C • 09/12 Capture the br ake cable in the cable clip as illustrat ed, then use a Phillips screw driver to attach the cable clips to bottom of work surface with the provided M2.
8 of 12 888-24-205-G-01 rev . C • 09/12 10 Set the desk upright onto its legs. CA UTION! LIFT HAZARD! T wo persons are requir ed for this step . F ailure to follow this warning may r esult in equipment damage and or personal injury . Set-up S teps 11 Adjust the riser on each leg and check with a lev el to make sur e the work surface is even.
9 of 12 12 1 2 888-24-205-G-01 rev . C • 09/12 Set-up S teps Install all equipment befor e removing the 4 brak e stop screw s. CA UTION! Make sure y ou leav e 20” (508mm) of slack in all cables to allow the w orksur face to raise up it’ s full 20” (508mm).
10 of 12 888-24-205-G-01 rev . C • 09/12 Adjustment Step 826-463-00 W ARNING Moving P ar ts Can Crush And C ut IMP A C T HAZ ARD 1. Release hand brake and r aise worksurface to highest position. 2. T urn adjustment nuts at back of legs counter clockwise until they stop (May requir e 40-60 rev olutions per leg).
11 of 12 = 14mm 1/4” 888-24-205-G-01 rev . C • 09/12 Release the hand brak e (on the right leg) and mov e the worksurface up to highest level . Push aside the c over loca ted behind each leg to acc ess the adjustment point.
12 of 12 888-24-205-G-01 rev . C • 09/12 Learn more about ergonomic computer use at: Más información sobre el uso ergonómico de ordenadores: Apprenez-en plus sur l’utilisation ergonomique d’u.
An important point after buying a device Ergotron WorkFit-D, Sit-Stand Desk (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ergotron WorkFit-D, Sit-Stand Desk yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ergotron WorkFit-D, Sit-Stand Desk - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ergotron WorkFit-D, Sit-Stand Desk you will learn all the available features of the product, as well as information on its operation. The information that you get Ergotron WorkFit-D, Sit-Stand Desk will certainly help you make a decision on the purchase.
If you already are a holder of Ergotron WorkFit-D, Sit-Stand Desk, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ergotron WorkFit-D, Sit-Stand Desk.
However, one of the most important roles played by the user manual is to help in solving problems with Ergotron WorkFit-D, Sit-Stand Desk. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ergotron WorkFit-D, Sit-Stand Desk along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
