Instruction/ maintenance manual of the product WM Low Profile Wall Mount, XL Ergotron
Go to page of 17
888-60-510-M-00 rev .B • 03/10 1 of 17 WM Large Display Low Pro le Wall Mount INSTRUCTIONS INSTRUCCIONES DE INSTALACIÓN NOTICE D’ASSEMBLAGE INSTRUÇÕES DE MONTAGEM Product Speci cations: W eight Capacity 79 kg (175 lbs) Mounting Options V erical Mount: W all plate attaches to vertical wall surfaces.
AB C 1 2 3 4 5 PENTA SCREW TOOL PENTA LOCKING SCREW M4x20mm M4x40mm M5x20mm M5x40mm M6x20mm M6x45mm M8x25mm 4x M8x50mm 4x 4x 4x 4x 4x 4x 4x M8x80mm 13mm 2 1 1x 1x 4x 4x 4x 1x 2x 2x v v MM MM 4x 4x 4x 8x 4x 5.1(ID) x 10(OD) x 6mm 5.
888-60-510-M-00 rev .B • 03/10 3 of 17 Y ou don ’t like to r ead installation instructions? W e understand–but considering the major investment a lar ge display represents, this isn’ t the time to take shortcuts.
a 1 888-60-510-M-00 rev .B • 03/10 4 of 17 * If a stand is already attached to your display , remove it acc ording to display manufacturer directions. Place the display on a clean, at, padded sur face or , if you prefer , lean the display against a stable, vertical surface.
v MM v MM b c Ø 888-60-510-M-00 rev .B • 03/10 5 of 17 TOP Arriba Haut Parte superior c Hole Depth Lay the display bracket ov er the display mounting holes and measure the depth of the display mounting holes with a slender stick.
a 2 b c 888-60-510-M-00 rev .B • 03/10 6 of 17 Compare this measur ement Compare this measurement to the recommended screw (based on display back type and diameter), taking into consideration the ne.
3 MM MM MM 888-60-510-M-00 rev .B • 03/10 7 of 17 T est Fasteners It is impor tant that you t est the chosen fastener combination to be sure it is the right size for your displa y : par tia.
4 a b x 1 = y 2 x ≤ 800mm 888-60-510-M-00 rev .B • 03/10 8 of 17 b Tighten screws with at least six, full, 360° revolutions*, but do not ov er tighten; ov er tightening may cause damage to display and/or brackets. * Six full turns will ensure a minimum thread engagement roughly equal to the diameter of the screw .
5 10 Ø 3/8" (10 mm) Ø 3/16" (5 mm) 12 888-60-510-M-00 rev .B • 03/10 9 of 17 Wood Madera Bois Madeira Concrete Concreto Béton Betão W ALL PLA TE MOUNTING INSTRUCTIONS Ergotron provides.
a 6 b 888-60-510-M-00 rev .B • 03/10 10 of 17 Wood Madera Bois Madeira A T T ACH RAIL TO W ALL Solid W ood Studs W ARNING: Ensure that the wall structure is capable of supporting four times the total weight of mounted equipmen t.
c d Ø 3/16" (5 mm) 14 888-60-510-M-00 rev .B • 03/10 11 of 17 c Hold rail against the wall to mark mounting holes. (Note rail orientation - front faces display , back faces wall - illustrated abov e.) Verify holes are lev el then drill pilot holes with 3/16” or 5mm W ood Drill Bit.
b 6 a 888-60-510-M-00 rev .B • 03/10 12 of 17 Concrete Concreto Béton Betão A T T ACH RAIL TO W ALL Solid Concrete * Before proceeding with this instal- lation, consult the manufacturer of your display for recommendations on choosing a mounting location that will ensure optimum performance.
c 3-1/8" (80 mm) Ø 3/8" (10 mm) 2x d 14 888-60-510-M-00 rev .B • 03/10 13 of 17 c Hold rail against wall to mark mounting holes. (Note rail orientation - front faces display , back faces wall - illustrated above .) Verify that the holes are level then drill pilot holes with pilot holes with 3/8” or 10mm Concrete Drill Bit.
7 4x 4x a b 888-60-510-M-00 rev .B • 03/10 14 of 17 a Hold Rail against wall and star t screws with washers. b Tighten screws with 13mm socket head (power tool is rec ommended) in the following sequence: 1st-lower right; 2nd-upper left; 3rd-low er left; 4th-upper right.
8 a b 888-60-510-M-00 rev .B • 03/10 15 of 17 Center of Displa y Located Over C enter of Stud - ALL OWED Centr o del monitor situado encima del centro de un larguero - PERMITIDO EPla.
9 LOCKING SCREW 2x SECURITY SCREW 2x ab 888-60-510-M-00 rev .B • 03/10 16 of 17 At the bottom of each of the display brackets, install and tighten either a Security Screws with Pentagon tool.
888-60-510-M-00 rev .B • 03/10 17 of 17.
An important point after buying a device Ergotron WM Low Profile Wall Mount, XL (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ergotron WM Low Profile Wall Mount, XL yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ergotron WM Low Profile Wall Mount, XL - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ergotron WM Low Profile Wall Mount, XL you will learn all the available features of the product, as well as information on its operation. The information that you get Ergotron WM Low Profile Wall Mount, XL will certainly help you make a decision on the purchase.
If you already are a holder of Ergotron WM Low Profile Wall Mount, XL, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ergotron WM Low Profile Wall Mount, XL.
However, one of the most important roles played by the user manual is to help in solving problems with Ergotron WM Low Profile Wall Mount, XL. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ergotron WM Low Profile Wall Mount, XL along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
