Instruction/ maintenance manual of the product TC-1428 Epson
Go to page of 16
14" SVGA Color Monitor TC-1428.
Customer’s Record The serial number of this product appears on the back of the unit. You should note this serial number in the space provided below and retain this manual as a permanent record of your purchase to aid in identification in the event of theft or loss.
2. The monitor will be automatically recovered to the on state by receiving normal sync. signals from PC. 3. The power management states are identified below: Power Mgmt.
1. Introduction Congratulations on your purchase of a NEW ULTRA VGA monitor. One of the most versatile monitors available today, the TC-1428 automatically adjusts its vertical and horizontal scanning frequencies to those of your computer’s graphics adapter or video chip sets.
4. Do not put the monitor or other heavy objects on the power supply cord. A damaged power cord may cause fire or electric shock. 5. Do not insert sharp objects into the monitor. They may cause fire or failure. 6. Do not allow liquids to spill into the cabinet.
4. Specifications Power Source: Power Consumption: Power Management: Picture Tube: Resolutions l Horizontal: * Vertical: Input Signals * Video: * Separate Sync: Synchronization * Horizontal: * Vertica.
Low Radiation: * X-ray radiation: < 100n Gylh * Magnetic field: Band I (5KHz-2KHz): < 250nT. Band II (2KHz-400KHz): < 25nT. Tilt and Swivel Operation: The swivel range is normally limited to a range of 45 degrees to the right or left of the front position (marked by a small molded pip on the top front bottom of the base).
5. Control Locations and Adjustments Note: The numbers indicate the control item whose description is found on the following page. -7-.
Adjustments 1. POWER Switch Push to turn the display on, and push again to turn off. The power indicator will light when the display is on. 2. BRIGHTNESS Control Adjusts the display to the desired brightness level. (factory preset at the center detent of the control knob) 3.
6. Connections Your monitor has two connecting cables: a Power Supply Cord, which connects to a wall outlet, surge protector or other power source, and a Signal Cable, which connects to the graphics adapter of your computer. To insure safety and correct operation, always follow these four steps when connecting the monitor: 1.
7. Pin Assignments The pin assignment of the video signal cable are shown below: 15-Pin Mini D-Sub Male Connector PIN NO. SIGNAL 1 RED 3 5 8 10 15 2 GREEN BLUE 4 GROUND or OPEN FOR DDC GROUND 6 R-GROUND 7 G-GROUND B-GROUND 9 NO CONNECTION GROUND or OPEN FOR DDC 11 GROUND 12 NO CONNECTION or DDC SDA 13 H.
8. Timing Charts SEPARATE SYNC. HORIZONTAL VERTICAL Sync. Polarity: Positive/Negative PRESET TIMING-VGA/SVGA Fh (KHz) A µs (Line time total) B µs (Synch. pulse) C µs (Back porch) D µs (Active) E µs (Front porch) Fv (Hz) P ms (Frame time total) Q ms (Synch.
PRESET TIMING-8514A/VESA VGA/UVGA Fh (KHz) A µs (Line time total) B µs (Synch. pluse) C µs (Back porch) D µs (Active) E µs (Front porch) Fv(Hz) P ms (Frame time total: Q ms (Synch. pulse) R ms (Back porch) S ms (Active) T ms (Front porch) H. Sync.
9. Troubleshooting Before you call an authorized service center, please check if the following items are properly connected or not. If a non-IBM personal computer or graphics adaptor is being used, make sure the pin assignments of signal input connector and the signal timing meet the specifications inducated above.
Federal Communications Commission Requirements Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
P/N:5035111312.
An important point after buying a device Epson TC-1428 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Epson TC-1428 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Epson TC-1428 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Epson TC-1428 you will learn all the available features of the product, as well as information on its operation. The information that you get Epson TC-1428 will certainly help you make a decision on the purchase.
If you already are a holder of Epson TC-1428, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Epson TC-1428.
However, one of the most important roles played by the user manual is to help in solving problems with Epson TC-1428. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Epson TC-1428 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
