Instruction/ maintenance manual of the product LX-300+ Epson
Go to page of 16
EPSON LX-300+ 5/00 EPSON LX-300+ - 1 User Replaceable Parts Options Single-bin Cut-sheet Feeder (C806371) Feeds up to 50 sheets of ordinary single-sheet paper. Additional Tractor Unit (C800301) Used in combination with the other tractor, improves continuous paper handling and reduces the chance of paper jams.
EPSON LX-300+ 2 - EPSON LX-300+ 5/00 Electrical Environmental Line spacing 1/6 inch or programmable in 1/216-inch increments Printable columns 80 columns (at 10 cpi) Resolution (maximum) 240 × 144 dp.
EPSON LX-300+ 5/00 EPSON LX-300+ - 3 Paper Use recycled paper, envelopes, and single-sheet multipart forms only under normal temperature and humidity conditions, as follows: Temperature: 59 to 77 °F (15 to 25 °C) Humidity: 30 to 60% RH Do not load paper that has been folded or is damaged, wrinkled, or curled.
EPSON LX-300+ 4 - EPSON LX-300+ 5/00 Paper Alignment Printing starts at “0” on the scale. The unprintable area is to the left of the “0”. Printable Area Single sheets and envelopes A The minimum top margin is 0.17 inch (4.2 mm). B The minimum left and right margins are 0.
EPSON LX-300+ 5/00 EPSON LX-300+ - 5 Safety Approvals 120 V Safety standards UL 1950 CSA C22.2 No. 950 EMI FCC part 15 subpart B class B CSA C108.8 class B 230 V Safety standards EN 60950 EMI EN 55022 (CISPR pub. 22) class B AS/NZS 3548 class B Acoustic noise Approx.
EPSON LX-300+ 6 - EPSON LX-300+ 5/00 Selecting Fonts After entering the Micro Adjust mode by holding down the Pause button for three seconds, you can change font settings with the Tear Off button. The two Tear Off lights come on ( n ) and go off ( o ) to show the current selection.
EPSON LX-300+ 5/00 EPSON LX-300+ - 7 Paper Positions Top-of-Form Position The top-of-form position is where the printer starts printing on single sheets or continuous paper. Tear-off Position Continuous paper is in the tear-off position when the perforation is aligned with the tear-off edge.
EPSON LX-300+ 8 - EPSON LX-300+ 5/00 Printing with the Pull Tractor To load continuous paper using the pull tractor, you must move the tractor to the pull tractor position, as described in steps 1 through 4 below. If your tractor is already installed in this position, make sure the printer is off and skip to step 7.
EPSON LX-300+ 5/00 EPSON LX-300+ - 9 7. Slide the left sprocket unit so that its sprockets match the position of the holes in the paper and lock the unit in place. Then slide the right sprocket unit to match the width of your paper, but do not lock it.
EPSON LX-300+ 10 - EPSON LX-300+ 5/00 To adjust the top-of-form position for continuous paper loaded on the pull tractor, see the following example: First mark a point 0.1 inch (2.5 mm) above the paper’s perforation; then position the paper so that the mark is even with the top edge of the plastic ribbon cover.
EPSON LX-300+ 5/00 EPSON LX-300+ - 11 5. After you set the tear-off position, press the Pause button to turn off the Micro Adjust mode. 6. Tear off the printed page(s). When you resume printing, the printer automatically feeds the paper back to the top-of-form position.
EPSON LX-300+ 12 - EPSON LX-300+ 5/00 Adjusting the Paper Thickness Lever Before printing on special paper, you need to change the paper thickness setting. The paper thickness lever is under the cover on the left side of the printer. The numbers next to the lever indicate the thickness setting.
EPSON LX-300+ 5/00 EPSON LX-300+ - 13 Default Settings While you can often set the default settings through your application software or printer driver, you may need to change a default setting from the printer’s control panel using the default setting mode.
EPSON LX-300+ 14 - EPSON LX-300+ 5/00 Bidirectional Alignment If you notice that the vertical lines in your printout are not properly aligned, you can use the printer’s bidirectional adjustment mode to correct this problem. To complete the steps below, you need 5 letter or A-4 size single sheets or 5 pages of continuous paper.
EPSON LX-300+ 5/00 EPSON LX-300+ - 15 Cleaning the Printer To keep your printer operating at its best, you should clean it thoroughly several times a year. Follow these steps: 1. Remove any paper loaded in the printer and turn it off. 2. Unplug the power cord from the electrical outlet; then disconnect the interface cable from the printer.
EPSON LX-300+ 16 - EPSON LX-300+ 5/00.
An important point after buying a device Epson LX-300+ (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Epson LX-300+ yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Epson LX-300+ - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Epson LX-300+ you will learn all the available features of the product, as well as information on its operation. The information that you get Epson LX-300+ will certainly help you make a decision on the purchase.
If you already are a holder of Epson LX-300+, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Epson LX-300+.
However, one of the most important roles played by the user manual is to help in solving problems with Epson LX-300+. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Epson LX-300+ along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
