Instruction/ maintenance manual of the product EPL-6000 Epson
Go to page of 9
EPL-6000 LASER PRINTER 1 Assembling the Printer 1 Before you can use the printer, you need to install a few important parts. Before proceeding, familiarize yourself with the components shown below. The basket is inside the printer and must be removed when you install certain parts.
EPL-6000 LASER PRINTER Mechanical Dimensions and weight: 1 Interface Specifications 1 Recommended duty cycle: MPBF (Mean Prints Between Failures): MTBF (Mean Time Between Failures): Durability: Electrical Voltage: Power consumption: Height: 8.3 inches (210 mm) Width: 16.
EPL-6000 LASER PRINTER Interface timing The figure below shows the timing for the parallel interface. SELECT -A DATA’-a 4 DATA STROBE ke.T ‘“i BUSY ACK A: 1 ps (min.) 8: 1 )B (min.) C: 1 ps (min.) D: approx. 6 ps Signal levels Output signals: Input signals: Vo,=Oto0.
EPL-6000 LASER PRINTER ) Switch Settings ) I I The DIP switches are located at the back of your printer and are numbered 1 through 8. The DIP switch settings are listed below. Use the tip of a ballpoint pen or another small pointed object to turn the switches ON or OFF.
EPL-6000 LASER PRINTER To take advantage of HP emulation, simply choose a printer driver from the list below. They are listed in order of priority. HP LaserJet series II HP LaserJet Plusm HP LaserJetTU The application program’s menu may list a number of more specific choices corresponding to various HP LaserJet font cartridges.
EPL-6000 LASER PRINTER 2. Locate the density control knob, which is in the front right comer inside the printer. 3. To make the print darker, turn the knob clockwise as shown below. Note: Increasing the print density increases toner consumption. if you increase the mint density, you need to replace the toner cartridge more frequently.
EPL-6000 LASER PRINTER If the message remains, the drum unit and the drum replacement cartridge must be replaced. See the section on replacing the drum unit in Chapter 6. COVER OPEN The printer cover is open. Close the cover and press the ON LINE button to set the printer on line and begin normal printing.
EPL-6000 LASER PRINTER Cleaning the laser beam lens Note: Cleaning the lens is required at an interval of 10,000 pages (the same interval as for changing the drum). If you wish, you can clean the lens when you change the drum and skip this procedure when you change the toner cartridge.
EPL-6000 LASER PRINTER 2 Insert the hooked edge of the developer cleaner about a half inch (13 mm) between the developer roller and the brass blade, as shown below. Draw the cleaner the full length of the developer unit several times, discarding excess toner.
An important point after buying a device Epson EPL-6000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Epson EPL-6000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Epson EPL-6000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Epson EPL-6000 you will learn all the available features of the product, as well as information on its operation. The information that you get Epson EPL-6000 will certainly help you make a decision on the purchase.
If you already are a holder of Epson EPL-6000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Epson EPL-6000.
However, one of the most important roles played by the user manual is to help in solving problems with Epson EPL-6000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Epson EPL-6000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
