Instruction/ maintenance manual of the product ENDEAVOR 486I Epson
Go to page of 10
EPSON ActionPC 7000, ActionTower 7000, Endeavor 486i hard disk access light RESET SPEED light POWER light (HDD) drive bays button / AC outlet / serial 1 serial 2 voltage switch POWER button RESET but.
EPSON ActionPC 7000, ActionTower 7000, Endeavor 486i Video Diskette Hard disk Interfaces Monitor Parallel Serial Keyboard Mouse Option slots Speaker Cirrus Logic GD5430 high-performance GUI accelerato.
EPSON ActionPC 7000, ActionTower 7000, Endeavor 486i Power Supply Type 200 Watt, UL/TUV/CSA listed, fan-cooled Input ranges 100-120 VAC or 200-240 VAC; switch-selectable Maximum +5 VDC at 20 Amps, -5 VDC at 0.5 Amp output +12 VDC at 8 Amps, -12 VDC at 0.
EPSON ActionPC 7000, ActionTower 7000, Endeavor 486i System Board Components The diagram below illustrates the components on the ActionPC 7000/ActionTower 7000/Endeavor 486i board.
EPSON ActionPC 7000, ActionTower 7000, Endeavor 486i System board components Connector J1 PS/2 keyboard connector J3 PS/2 mouse connector J4 Serial 2 port connector J5 Serial 1 port connector J6 Print.
EPSON ActionPC 7000, ActionTower 7000, Endeavor 486i SIMM configurations (continued) Bank0 Bank1 Bank2 Bank3 Total (SIM1) Type (SIM2) Type (SIM3) Type (SIM4) Type memory 16MB Single 16MB Single 8MB Do.
EPSON ActionPC 7000, ActionTower 7000, Endeavor 486i Hard Disk Drive Information DMA Assignments The following table lists parameters for hard disk drives qualified for use in the computer.
EPSON ActionPC 7000, ActionTower 7000, Endeavor 486i System I/O Address Map Serial port connector pin assignments (J4 and J5) Pin Signal Pin Signal 1 Data carrier detect 6 Data set ready 2 Receive dat.
EPSON ActionPC 7000, ActionTower 7000, Endeavor 486i IDE drive connector pin assignments and J14) *Active low logic Option card riser board connector pin assignments * Active low logic ISA option slot.
EPSON ActionPC 7000, ActionTower 7000, Endeavor 486i Tested Operating Environments The following operating environments have been tested for compatibility with the system. Microsoft® MS-DOS® 3.3 and later Novell® DR DOS® Novell NetWare®* 3.12 and 4.
An important point after buying a device Epson ENDEAVOR 486I (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Epson ENDEAVOR 486I yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Epson ENDEAVOR 486I - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Epson ENDEAVOR 486I you will learn all the available features of the product, as well as information on its operation. The information that you get Epson ENDEAVOR 486I will certainly help you make a decision on the purchase.
If you already are a holder of Epson ENDEAVOR 486I, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Epson ENDEAVOR 486I.
However, one of the most important roles played by the user manual is to help in solving problems with Epson ENDEAVOR 486I. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Epson ENDEAVOR 486I along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
