Instruction/ maintenance manual of the product CMD-2260 Epson
Go to page of 18
EPSON ® ATA/IDE CD-ROM DRIVE USER’S MANUAL CMD-2260 6X CD-ROM Drive.
FEDERAL COMMUNICATIONS COMMISSION (FCC) RADIO FREQUENCY INTERFERENCE STATEMENT Class B Computing Device Note: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules.
USER’S MANUAL FOR CMD-2260 6X ATA/IDE CD-ROM DRIVE UNIT Laser Safety Information Handling Precautions Drive Parts and Functions Hardware Installation Software Installation Device Driver Installation MSCDEX.
LASER SAFETY INFORMATION Class 1 LASER Product This equipment is certified to comply with DHHS Rule 21 CFR Chapter 1, Subchapter J in effect as of date of manufacture. Caution: (1) Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
HANDLING PRECAUTIONS DISC HANDLING l Hold the disc by the edges. Do not touch the surface of the disc, especially the bottom of the disc. l To remove dust or finger prints, use a clean soft dry cloth. Do not use thinners or cleaners on the disc. l Do not write with a hard tip pen on the surface.
DRIVE PARTS AND FUNCTIONS FRONT PANEL 1. HEAD PHONE JACK Connects headphone, use 3.5mm stereo mini plug. 2. VOLUME Adjust audio output level. 3. BUSY INDICATOR Power on and drive ready/busy indicator. 4. DISC TRAY Accepts a CD-ROM disc. 5. REVERSE SELECT - Audio CD Function Only Manually steps backwards for track selection 6.
REAR PANEL 1. AUDIO OUT CONNECTOR Standard card connector pins 2. INTERFACE MODE SELECTOR A. CSEL (Cable Select) B. SLAVE (Factory Default) C. MASTER 3.
HARDWARE INSTALLATION SYSTEM REQUIREMENTS You need the following equipment to install your CD-ROM Drive: l IDE compatible sound card or IDE interface card l IBM PC/AT or compatible l 3.
5. Connect the 40-pin drive interface and sound cable at the rear of the CD-ROM drive. To prevent an incorrect connection and possible system damage, place Pin 1 of the cable connector (red colored edge of the cable) to Pin 1 on the ATAPI drive connector.
SOFTWARE INSTALLATION 1. Insert the installation disk into Drive A or Drive B. (Not required for Windows ‘95 installations - see page 20). 2. At the DOS prompt, type the drive letter where the disk is inserted, followed by a colon. Press ENTER 3. Type install and press ENTER.
6. The defaults provided by the program are: Primary/Secondary: Primary Master/Slave: Slave Assigned Drive Letter: Next Available Drive ** Memory Buffer Size 12 ** Verbose Mode: On ** ** These settings are utilized by the MSCDEX.EXE program. Complete documentation is available in your MS-DOS manual.
8. Your computer MUST now be rebooted for all changes to become effective. ATA/IDE Owner’s Manual 12.
DEVICE DRIVER INSTALLATION The Device Driver, EPSON. SYS, is described below. DEVICE=[drive:][path]EPSON.SYS /D:device-name /M: /P: /I: /V For example: DEVICE=C:EPCDROM/EPSON.SYS /D:EPSON00l /M:S /P: 1F0s /I:14 /V . [drive:][path] specifies the drive and the path name in use.
MSCDEX.EXE INSTALLATION INSTRUCTIONS MSCDEX.EXE must be included in the AUTOEXEC.BAT tile. The MSCDEX.EXE will be invoked each time the system boots up. The syntax is as follows: C: <path> MSCDEX.EXE / D:<device name. /L:<drive letter>/M:<buffersize> Example: C:DOSMSCDEX.
Additional Installation Instructions Installing CD Audio Player For Windows If “CD Audio” is not available in your Windows Accessories Group “Media Player”, you must complete the following ste.
PRODUCT FEATURES SPECIFICATIONS Disc Applicable Disc Disc Diameter Performance Data Rate - Sustained Data Rate - Burst Access Time 1. Tested with MPCII Wizard 2.
Technical Support TROUBLESHOOTING Check the table below for common problems and solutions. PROBLEM CORRECTIVE ACTION l When you play a CD there is no image on the screen. There are several probable causes for this problem. The disc might be an audio CD with no screen images.
Technical Support Options The following Technical Support options are available if you have questions or concerns: Call Epson Technical Support at 800-922-8911 On CompuServe, GO EPSON or contact us di.
An important point after buying a device Epson CMD-2260 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Epson CMD-2260 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Epson CMD-2260 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Epson CMD-2260 you will learn all the available features of the product, as well as information on its operation. The information that you get Epson CMD-2260 will certainly help you make a decision on the purchase.
If you already are a holder of Epson CMD-2260, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Epson CMD-2260.
However, one of the most important roles played by the user manual is to help in solving problems with Epson CMD-2260. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Epson CMD-2260 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
