Instruction/ maintenance manual of the product Apex-80 Epson
Go to page of 149
.
FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment generates and uses radio frequency energy and if not installed and used prop erly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception.
Contents Introduction.. .......................................... . 1 Apex80 Features .......................................... . 1 About This Manual ....................................... . 2 Where to Get Help .....................................
Chapter 4 Apex80 Printer Features Quality and Fonts ..................................... . 4-1 Print Size and Character Width ........................... . 4-2 Special Effects and Emphasis ............................. . 4-3 Using Different Character Sets .
Appendix C Problem Solving and Maintenance Problem/Solution Summary .............................. . C-1 beeper Error Warnings ................................... . C-4 Data Dump Mode ...................................... . C-4 Coding Solutions .....
Introduction The Epson Apex80 printer combines low price with high quality printing and advanced features. Apex80 Features In addition to the high performance and reliability you’ve come to expect from Epson printers, the Apex80 offers the following: l Draft mode for quick printing.
About This Manual Chapter 1 gives you step-by-step instructions on setting up your new printer, and Chapters 2 through 6 cover the basic and advanced functions. The appendixes contain reference information, including all the details you need to use any of the printer’s commands, and some advice on solving problems.
Chapter 1 Setting Up To set up your Apex80 printer, simply follow the steps in this chapter. Identifying Printer Parts First, see that you have all the parts you need. In addition to this manual, the printer box should contain the items shown in Figure 1-1.
In addition to the items in the box, you need a proper shielded cable to connect the printer to your computer. You may also need an interface board, which is necessary only for those computers that can’t use the Centronics ® parallel interface.
Installing the Paper Feed Knob Now that you have decided where to locate your Apex80 printer, the first step in setting it up is installing the paper feed knob. Follow these steps: 1. Locate the paper feed knob, which is packed into an indentation in the white foam material.
To install the ribbon, follow these steps: 1. Remove the lid at the front of the printer by lifting the handles. Removing the lid enables you to see the print head, which is shown in Figure 1-3.
4. Insert the cartridge by placing the black hooks on each side of the cartridge into the slots located inside the printer in the right and left front corners. Push down until the cartridge snaps into place. (See Figure 1-4.) Figure 1-4. Ribbon cartridge installation 5.
Figure 1-5. Directing the ribbon 6. Replace the front lid by inserting its legs into the slots near the front corners of the printer. Lay the lid down and press to snap it into place. Replacing the Ribbon When your printing becomes light and you need to replace the ribbon, follow these steps: 1.
Using Continuous-feed Paper The following section covers use of continuous-feed paper with your tractor unit. If you plan to use single-sheet paper, skip to the Using Single-sheet Paper section later in this chapter. The tractor unit for the Apex80 allows you to use paper with pin feed holes along the sides (continuous-feed paper).
Figure 1-6. Removing the tractor unit slot cover 3 Fit the paper rest into the slots along the top edge of the back of the printer and snap it into place.
4. 5. Pull the paper release lever forward. (See Figure 1-8.) The double- arrow icon in front of the lever marks the position the lever should be in for using continuous-feed paper (or for releasing paper). Now install the tractor unit. First, hold the unit so that its black legs are facing downward, as shown in Figure 1-8.
6. In each tractor slot, located at each side of the paper slot, is a peg that fits into the notch on each of the rear tractor legs. Tilt the tractor back so that the rear notches fit over these pegs. See Figure 1-9. Figure 1-9. Installing the tractor unit 7.
4. Using Figure 1-10 as a guide, pull the locking levers on each side of the pin feed holders forward so you can move the pin feed holders. Figure 1-10. Locking lever fur pin feed holder adjustment 5. Place the left holder approximately 3/4 of an inch from the far left position and then push the locking lever back to fasten that holder into place.
7. Feed the paper into the paper slot. Push and maneuver the paper through the slot until it comes up between the ribbon guide and the platen. 8. Pull the paper up until the top is above the pin feed holders. Fit the holes along the left edge of the paper over the pins in the left holder, as shown in Figure 1-12, and close the pin feed cover.
For continuous-feed paper, move the edge guides to the far right and left positions on the paper guide. You won’t be inserting paper through the edge guides unless you use single-sheet paper. 2. Insert the legs of the paper guide into the slots behind the tractor unit, keeping the guide tilted backward as you do so.
3. When the legs are in the slots, lean the guide all the way back. The guide should rest atop the paper entering the printer, separating it from paper exiting the printer. Setting top of form Now you are ready to set the top of form position. Follow these steps: 1.
Once you have set the top of form, each time you finish printing a document, push the ON/OFF LINE button to put the printer offline and then push the FORM FEED button once to advance the paper one sheet. This enables you to tear off your just-printed pages and leave th paper in the correct position to begin the next document.
Installing the paper guide Install the paper guide as follows: 1. If you have not already done so, install the edge guides on the paper guide by hooking the tab on the back of each guide over the top of the paper guide, as shown in Figure 1-13. Snap the bottom of each edge guide into place.
3. Align the left side of the left edge guide with the guide mark on the paper guide. See Figure 1-17. You may later wish to adjust this edge guide depending on the margin setting in your application program.
Figure 1-18. Apex80 ready for automatic paper loading 6. Press and release the AUTO LOAD button (the same button as the DRAFT/LINE FEED button). The paper is automatically loaded to the top of the page. 7. Push the ON/OFF LINE button so that the printer is ready to accept data.
Reloading during printing When you print a document more than one page long using single- sheet paper, there are two ways your software can enable you to load a new sheet at the end of a page: l If your software sends characters in a continuous stream, the printer stops printing when it reaches the bottom of the paper.
Figure 1-19. Control panel There are four indicator lights and three buttons on the control panel. Indicator lights The indicator lights give you information on the printer’s status: l The POWER light glows green when the power is on. l The READY light glows green when the printer is ready to receive data.
fully-formed characters for final copies or special purposes. NLQ is available in both Roman and Sans Serif fonts. The printout below shows the differences among draft, NLQ Roman, and NLQ Sans Serif so that you can compare the different styles and densities: See Chapter 4 for more information on these modes and ways to select them.
2. Turn the power switch off, then hold down the DRAFT button on the control panel while you turn the power back on. The Apex80 begins printing letters, numbers, and other characters that are stored in its ROM (Read Only Memory) in draft mode. (If DIP switch 1-5 has been turned on, the test will be performed in NLQ mode, as in step 4 below.
Connecting the Apex80 to Your Computer Now that the test pattern has shown that your printer is operational, it’s time to hook it up to your computer.
3. Secure the plug to the printer with the wire clips on each side of the connector. Press the clips into the metal clasps at each side of the plug. These clips ensure that your cable will not be loosened or unplugged accidentally. 4. If your cable has a grounding wire, fasten it to the grounding screw below the connector.
Chapter 2 Using the Apex80 with Application Programs Now that you’ve set up and tested the printer, you need to start using it with your application programs. Printer Selection Menus Most application programs let you specify the type of printer you’re using so that the program can take full advantage of the printer’s features.
A quick test After setting up your application program, print a sample document to be sure the program and the Apex80 are communicating properly. If the document doesn’t print correctly, recheck the program’s printer selection and installation procedure.
The hexadecimal, or hex, system is based on units of 16 and is often used by programmers. Instead of using only the numerals 0 through 9, the hex system also uses the letters A through F. For example, the decimal numbers 9, 10, 11, and 12 are 09, 0A, 0B, and 0C in hex.
Check the manual for your word processor to see if you can place printer commands in your text. If this is possible, use the Command Summary (Appendix A) in this manual to find the command, and use the manual for your word processor to find how to assign the command.
Table 2.1. Characters per line Normal 80 Elite 96 Condensed 132 Condensed Elite 160 Therefore, if your spreadsheet asks the number of columns your printer can print, decide which mode you will use and supply the appropriate number from Table 2-1.
If you’re using the program’s print facility, recheck the Command Summary to make sure you’re sending the correct commands. If you’re still having difficulty printing, check the troubleshooting section in your spreadsheet program’s manual or Appendix C of this manual.
Sending printer commands with BASIC You can send printer commands with any programming language. The examples in this manual are written in BASIC, because BASIC is included with most computer systems.
Chapter 3 SelecType The Apex80’s SelecType feature can produce four special typestyles: SelecType Operation Using SelecType is easy. You turn on SelecType and select a typestyle, then turn off SelecType and print. Turning SelecType on 1. Make sure that the printer is on line.
Selecting typestyles In SelecType, each button has a function: l ON/OFF LINE selects typestyles. l FORM FEED sets the styles. l LINE FEED turns SelecType off. After turning on SelecType, follow these steps to select a typestyle: 1. Find the typestyle you want in Table 3-1.
When you press the ON/OFF LINE button to select an additional mode, start counting again where you left off. That is, if you have selected emphasized and wish to combine that with elite, press the ON/OFF LINE button three more times, not four, to select elite.
l If there are print codes in the document or file you are printing, those codes will override your SelecType settings. This seldom happens, since you usually won’t use SelecType with files that hav.
Chapter 4 Apex80 Printer Features You can obtain many different printing effects with the Apex80 printer, from arranging the printout on the paper to giving extra emphasis to particular words and phrases. This chapter shows you the features you may want to select with your software.
Print Size and Character Width To add greater variety to your documents, the Apex80 has two pitches and condensed printing. All can be selected either with SelecType or a software command, and software commands also offer another option: double-wide. Pitches The two pitches are pica and elite.
Widening or narrowing the characters also widens or narrows the spaces between words and letters. Because word processors usually create a left margin by printing spaces, you may need to change the number of characters on a line to keep the margins correct if you change widths.
Using Different Character Sets The Apex80 incorporates a new character set: Epson Character Graphics. This set allows you to take advantage of the power of the Epson mode commands and still print out the character graphics used by IBM and compatible computers and by much commercial software.
Page Layout and Other Commands The remaining commands in the Command Summary are not normally needed when using commercial software. You may need some of them if you are using a printer installation p.
Chapter 5 User-defined Characters The Apex80 has several hundred different characters stored in its ROM (Read Only Memory Although this number includes draft, italic, international, Character Graphics, and NLQ (Near Letter Quality) characters, sometimes you may want to have a few more.
You can create any type of character. The only restriction is that the characters you define must follow the same rules that govern the rest of the characters printed by the Apex80. They must fit into an 11 x 9 matrix, no dot can overlap another, and either the top or the bottom row must be empty.
the dots as large as you see them in the example on the left in Figure 5-2. If you draw them smaller, you may have overlapping dots without realizing it. Figure 5-2. Correct and incorrect designs overlapping dots dot on horizontal line If you do accidentally overlap dots, don’t worry.
200 FOR X=1 TO 9 210 LPRINT CHR$(F(X));:NEXT X 220 LPRINT CHR$(0)CHR$(0); 230 LPRINT "YOUR CHARACTER IN PICA: < < <" 240 LPRINT "IN DOUBLE-WIDE EMPHASIZED PICA: "; 250 LPR.
To see program 1 produce the character in Figure 5-3, run the program and follow these instructions: 1. When the screen message asks what rows have dots in column 1, press Enter to indicate that no dots go in that column. 2. For column 2 (the vertical line) press 7, Enter, 5, and Enter again to indicate that you want dots in rows 7 and 5.
Figure 5-4. Using the bottom eight rows Second definition program Once the character looks the way you want it to, you can enter, modify, and run the next program. The program as listed creates the Mercury character, but you can use it for any characters you create if you make one or two changes, as explained after the program listing.
created more than one character, put the DATA numbers for each character on a separate line as you see in the example below: 210 DATA 112,8,0,138,116,138,0,8,112 220 DATA 56,68,146,40,130,40,130,68,56 Check your work by making sure there are nine numbers in each line and the numbers are separated by commas.
you use the grid and the programs in this section, however, you can design your own NLQ characters. NLQ grid Because the NLQ characters can use as many as 18 dots vertically and 12 dots horizontally, you plan your designs on a different grid than the one you used for draft characters.
Each NLQ character definition requires 36 data numbers. Therefore, each vertical column must be divided into three sections for the calculation of data numbers. The process is not difficult once you get some practice using it. Figure 5-6 shows a single column to make clear how the data numbers are calculated.
positions) and add the values of any dots that are used there. Finally, you look at the bottom group (two dot positions) and add together the values used there. If no dots are used in a group, the data number for that group is zero. All zeros must be entered in the DATA statements for the NLQ definition programs.
If you look at each column individually, you can see how the data numbers were calculated. First NLQ definition program Now type in and run the following program. It has the data numbers for the arrow design. For a character of your own, change the data numbers in lines 130-150.
10 J=l: IF J>3 THEN A=58 ELSE A=60 20 LPRINT CHR$(27)"x"CHR$(1) 30 FOR X=58 TO 63: LPRINT CHR$(X)" ";: NEXT X 40 LPRINT 50 LPRINT CHR$(27) :""CHR$(0)CHR$(0)CHR$(0) 60 .
Chapter 6 Introduction to Dot Graphics The dot graphics mode allows your Apex80 to produce pictures, graphs, charts, or almost any other pictorial material you can devise.
If you use commercial software that produces graphics, all you need to know about dot graphics is how to use the software. If, on the other hand, you wish to do your own programming or merely wish to understand how the Apex80 prints graphics, read on.
Dot patterns The Apex80’s print head is able to print graphics in addition to text because graphic images are formed on the Apex80 about the same way that pictures in newspapers and magazines are printed. If you look closely at a newspaper photograph, you can see that it is made up of many small dots.
To fire any one pin, you send its number. To fire more than one pin at the same time, add up the numbers of the pins and send the sum to the printer. Therefore, with these labels for the pins, you fire the top pin by sending 128. To fire the bottom pin, you send 1.
The graphics command format There are several different graphics commands giving different horizontal dot densities and printing speeds. Because the format is almost the same for all the commands, however, the example here keeps things simple by using only the single-density graphics command, ESC K.
Graphics data After receiving a graphics command such as ESC K nl n2, the printer prints the number of codes specified by nl and n2 as graphics data, no matter what codes they are. This means that you must be sure to supply exactly the right amount of graphics data.
WIDTH statements Some software (including most versions of BASIC) automatically inserts carriage return and line feed codes after every 80 or 130 characters. This is usually no problem with text, but it can spoil your graphics. Two extra columns of graphics are printed in the middle of the ones you send, and are left over and printed as text.
1. The computer is prevented from adding any extra characters by the WIDTH statement (line 100). 2. The line spacing is changed to 8/72 of an inch-the height of the dot patterns used in the program (line 110). 3. The program goes through the graphics commands the required number of times (lines 120 and 170).
Table 6-1. Graphics modes Modes 4-6 in the table are special modes that alter the horizontal density to give proportions of a computer monitor (the CRT modes), or to match the vertical density so as to give round circles (the plotter mode).
A little experimentation should tell you whether the reassigning code can improve your graphics printouts. Designing Your Own Graphics This section takes you through the development of a graphics program. The example is not especially complicated, but it does include the same steps you would use for a more complex figure.
Now look at the high-speed doubledensity design in Figure 6-3. It should point you in the right direction for your own work. Figure 6-3. Arrow design After plotting the dots on a grid, you calculate the numbers for each pin pattern by dividing the design grid into separate print lines.
The numbers for the second line were calculated in the same way. Once the numbers for the pin patterns are calculated, they are put in the program in DATA statements, separated by commas. The program works in a similar way to the last example. This time it selects 7/72-inch line spacing because only seven pins are used.
Appendix A Command Summary This appendix lists and describes all the commands available on the Apex80. The first part of this appendix lists all commands in numerical order and gives the page number where each is fully described. If you know which command you are looking for, consult the numerical list to find the page number where it is described.
For the following commands that use only 0 or 1 for the variable, either the ASCII cocks 1 and 0 or the characters 1 and 0 can be used: ESC S , ESC U, ESC X , ESC W, ESC S, ESC- , and ESC % For exampl.
Control key chart Some application programs can use control key codes for decimal values O-27. The table below gives you the proper values. The Control Key column indicates that you press the control .
Commands in Numerical Order This section lists all the Apex80 commands, with their decimal and hexadecimal values. The numbers in the columns on the right are the page numbers in this appendix where a complete description of the command can be found.
ASCII Dec Hex Description Page ESC 4 52 34 ESC 5 53 35 ESC 6 54 36 ESC 7 55 37 ESC 8 56 38 ESC 9 57 39 ESC : 58 3A ESC < 60 3C ESC ? 63 3F ESC @ 64 40 ESC A 65 41 ESC B 66 42 ESC C 67 43 ESC CO 67 .
ASCII Dec Hex Description Page ESC 1 108 6C Set left margin A-16 ESC s 115 73 Turn half-speed mode on/off A-8 ESC t 116 74 Select character table A-26 ESC x 120 78 Select NLQ or draft A-19 A-6 Command.
Printer Operation Initialization ESC @ Initialize Printer Format: ASCII code: ESC @ Decimal: 27 64 Hexadecimal: 1B 40 Comments: Resets the printer mode and clears the buffer of printable data on the print line preceding the command.
Speed ESCs Turn Half-speed Mode On/Off Format: ASCII code: ESC s n Decimal: 2 7 175 n Hexadecimal: 1B 73 n Comments: The following values can be used for n: 1: Mode is turned ON. (The characters “0” and “1” 0: Mode is turned OFF. can also be used.
ESC 8 Disable Paper-out Sensor Format: ASCII code: ESC 8 Decimal: 27 56 Hexadecimal: 1B 38 Comments: Turns off the paper-out sensor so that you can print to the end of a single sheet of paper. ESC 9 Enable Paper-out Sensor Format: ASCII code: ESC 9 Decimal: 2 7 5 7 Hexadecimal: 1B 39 Comments: Cancels ESC 8.
Beeper BE L Beeper Format: ASCII code: BEL Decimal: 7 Hexadecimal: 0 7 Comments: Sounds the printer’s beeper. Data Control CR Format: ASCII code: C R Decimal: 13 Hexadecimal: 0D Comments: Carriage Return Prints the data in the buffer and returns the print position to the left margin.
DEL Delete Character Format: ASCII code: DEL Decimal: 127 Hexadecimal: 7F Comments: Removes the last text character on the print line but does not affect control codes.
ESC C 0 Set Page Length in Inches Format: ASCII code: ESC C NUL n Decimal: 27 67 0 n Hexadecimal: 1B 43 00 n Comments: Sets the page length to n inches.
Line feeding LF Line Feed Format: ASCII code: LF Decimal: 10 Hexadecimal: 0 A Comments: ‘When this command is received, the data in the print buffer is printed and the paper advances one line in the current line spacing.
ESC 2 Format: ASCII code: ESC 2 Decimal: 2 7 50 Hexadecimal: 1 B 32 Comments: Select 1/6-inch Line Spacing Sets the line spacing to l/6 of an inch for subsequent line feed commands. The “2” is the character two and not ASCII code 2. This is the default at power on.
ESC J Perform n/216-inch Line Feed Format: ASCII code: ESC J n Decimal: 27 74 n Hexadecimal: 1B 4A n Comments: Advances the paper n/216 of an inch. The value of n must be from O-255. This command produces an immediate line feed but does not affect subsequent line spacing and does not produce a carriage return.
ESC b Set Vertical Tabs in Channels Format: ASCII code: ES C b c n 1 n 2 .. . NU L Decimal: 2 7 9 8 c n 1 n 2 .. . 0 Hexadecimal: 1 B 6 2 c n 1 n 2 .. . 0 0 Comments: Functions the same as ESC B, except that the variable c selects a channel for the vertical tabs, which must be between O-7.
ESC Q Set Right Margin Format: ASCII code: ESC Q n Decimal: 27 81 n Hexadecimal: 1B 51 n Comments: Sets the right margin to n columns in the current pitch. This command clears previous tab settings and all previous characters in the print line. The minimum space between the margins is the width of one double-wide pica character.
ESC f Horizontal/Vertical Skip Format: ASCII code: ESC f n s Decimal: 27 102 n s Hexadecimal: 1 B 66 n s Comments: Prints spaces or line feeds without carriage returns. When n is 0, s spaces will be inserted up to a maximum of 127. If n is set to 1, s line feeds will be performed.
Overall Printing Style ESC x Select NLQ or Draft Format: ASCII code: ESC x n Decimal: 27 120 n Hexadecimal: 1B 78 n Comments: The following values can be used for n: 0: Selects the draft mode. (The characters “0” and “1” 1: Selects the Near Letter can also be used.
ESC! Format: ASCII code: ESC ! n Decimal: 27 33 n Hexadecimal: 1 B 21 n Comments: Master Select Selects any valid combination of the modes in the table below. The variable n is determined by adding together the values of the desired modes from the table.
ESC M Select Elite Pitch Format: ASCII code: ESC M Decimal: 27 77 Hexadecimal: 1B 4D Comments: Selects elite pitch (12 characters per inch). SI Select Condensed Mode Format: ASCII code: SI Decimal: 15 Hexadecimal: 0 F Comments: Prints characters at about 60 percent of their normal width.
SO Select Double-wide Mode (one line) Format: ASCII code: S O Decimal: 1 4 Hexadecimal: 0 E Comments: Double-wide mode doubles the width of all characters. This mode is cancelled by a carriage return or DC4. Esc so Select Double-wide Mode (one line) Format: ASCII code: ESC S O Decimal: 27 14 Hexadecimal: 1B 0E Comments: Duplicates the SO command.
ESC W Turn Double-wide Mode On/Off Format: ASCII code: ESC W n Decimal: 27 87 n Hexadecimal: 1 B 57 n Comments: The following values can be used for n: 1: The mode is turned ON. (The characters “0” and “1” 0: The mode is turned OFF. can also be used.
ESC G Select Double-strike Mode Format: ASCII code: ESC G Decimal: 27 71 Hexadecimal: 1B 47 Comments: Makes text bolder by printing each line twice, with the second printing slightly below the first. In NLQ the mode is not available but is not cancelled.
ESC S l Format: ASCII code: ESC S SOH Decimal: 27 83 1 Hexadecimal: 1 B 53 01 Comments: Select Subscript Mode Prints characters about two-thirds of the normal height in the lower part of the character space. The ASCII code 1 or the character “1” can be used in this command.
Word Processing ESC a NLQ Justification Format: ASCII code: ESC a n Decimal: 27 a n Hexadecimal: 1B 61 n Comments: The following values can be used for n: 0: Selects left justification. 1: Selects centering. 2: Selects right justification. 3: Selects full justification.
ESC 4 Select Italic Mode Format: ASCII code: ESC 4 Decimal: 2 7 5 2 Hexadecimal: 1 B 3 4 Comments: Causes characters from the italic character set to be printed. This command is valid even if the Epson Character Graphics set has been selected by ESC t or DIP switch 1-3, but character graphics cannot be italicized.
ESC R Select an International Character Set Format: ASCII code: ESC R n Decimal: 27 82 n Hexadecimal: 1 B 52 n Comments: See Appendix B for more information on international character sets.
User-defined Characters Note: See Chapter 5 for sample programs and full information on this topic. ESC & Define User-defined Characters Format: ASCII code: ESC & NUL d1 d2 ... d n Decimal: 27 38 0 d1 d2 ... dn Hexadecimal: 1B 26 00 d1 d2 ... dn Comments: This command allows characters to be redefined in the currently selected mode.
Graphics Note: See Chapter 6 for sample graphics programs. ESC K Select Single-density Graphics Mode Format: ASCII code: ESC K n1 n2 Decimal: 27 75 n1 n2 Hexadecimal: 1B 48 n1 n2 Comments: Turns on eight-pin single-density graphics mode (60 dots per inch).
ESC Z Select Quadruple-density Graphics Mode Format: ASCII code: ESC Z n1 n2 Decimal: 27 90 n1 n2 Hexadecimal: 1B 5A n1 n2 Comments: Turns on eight-pin quadruple-density graphics mode (240 dots per inch). The total number of columns = nl + (n2 x 256).
ESC” Select 9-Pin Graphics Mode Format: ASCII code: ESC ˆ m n1 n2 Decimal: 27 94 m n1 n2 Hexadecimal: 1B 5 E m n1 n2 Comments: Turns on 9-pin Graphics Mode. For this command the variable m defines density of print (0 for single and 1 for double). The total number of columns = nl + (n2 x 256).
Appendix B Character Tables This appendix contains tables of the complete Apex80 character set, including the extra characters for the 13 Epson international character sets. The tables give a printout of each character and the codes in decimal and hexadecimal.
Table B-1. Apex80 characters Decimal Hex Character ASCII name 0 00 1 01 2 02 3 03 4 04 5 05 6 06 7 07 8 08 9 09 10 0 A 11 0 B 12 0C 13 O D 14 OE 15 OF 16 10 17 11 18 12 19 13 20 14 21 15 22 16 23 17 2.
Table B-1, continued Dec Hex Char Dec Hex Char Dec Hex Char 32 20 33 21 34 22 35 23 36 24 37 25 38 26 39 27 40 28 41 29 42 2A 43 2 B 44 2C 45 2D 46 2E 47 2F 48 30 49 31 50 32 51 33 52 34 53 35 54 36 55 37 56 38 57 39 58 3A 59 3B 60 3C 61 3D 62 3E 63 3F SP ! " # $ % & ' ( ) * + ' — .
Table B-1, continued Dec Hex Italic Italic Graphic Graphic set w/ESC 6 set w/E S C 7 128 80 129 81 130 82 131 83 132 84 133 85 134 86 135 87 136 88 137 89 138 8 A 139 8 B 140 8C 141 8D 142 8E 143 8F 1.
Table B-1, continued Dec Hex Italic Italic Graphic Graphic set w/ESC 6 set S w/E C 7 160 A0 161 A1 162 A2 163 A3 164 A4 165 A5 166 A6 167 A7 168 A8 169 A9 170 AA 171 AB 172 AC 173 AD 174 AE 175 AF 176.
Table B-1, continued Dec Hex Italic Italic Graphic Graphic set w/ESC 6 set w/E SC 7 192 C0 193 C1 194 C2 195 C3 196 C4 197 C5 198 C6 199 C7 200 C8 201 C9 202 CA 203 CB 204 c c 205 CD 206 CE 207 CF 208.
Table B-1, continued Dec Hex Italic ltalic Graphi c set Graphic set w/ESC 6 w/E S C 7 224 E O 225 E1 226 E2 227 E3 228 E4 229 E5 230 E6 231 E7 232 E8 233 E9 234 E A 235 EB 236 EC 237 ED 238 EE 239 EF .
International Character Sets Twelve character codes between 35 and 126 can represent more than one character each, depending upon the international character set you select. You can make the choice either by setting DIP switches 1-6 through 1-8 or by using the ESC R command.
Appendix C Problem Solving and Maintenance This appendix approaches troubleshooting from several directions. The first section uses a columnar format to match solutions with problems.
Printing is patchy, faint, uneven, or intermittent Solution Check that the ribbon is seated correctly If you have been using the ribbon for a long time or for a large amount of printing, it may need to be replaced.
Problem Solution Strange things print in graphics mode Printer freezes in graphics mode Can’t get a full page in width Some systems require a WIDTH statement. See your system documentation. Many computers have problems sending one or more of the codes between 0 and 13.
Problem Solution Can’t deactivate paper-out Computer systems that monitor printer sensor with either DIP switch cable pin 12 ignore both ESC 8 and the 1-4 or ESC 8 setting of switch 1-4. These systems stop the printing when no paper is in contact with the paper-end detector (a small switch located behind the platen).
The hexadecimal numbers are the codes received by the printer, and the guide section helps you find a certain place in the list of codes. Each character in the guide section corresponds to one of the codes. If the code is for a printable character, that character is printed.
Some computer systems change one or more codes when sending them from BASIC to the printer. The ability of the Apex80 to dump in hexadecimal lets you determine which codes are creating problems for your system. A hex printout of a program shows you exactly what the printer is receiving, regardless of what the computer is sending.
There are four common approaches. First, you may be able to buy an alternative interface board for your system. This is the best solution for 7-bit system problems. Check with your dealer or call the Epson 800 number. The second approach is to use commercially available software that is specifically designed to overcome these coding problems.
Apple ® II solutions Apple II computers pose two types of problems. The first is that the Apple II is an 8-bit computer, but its printer interface handles only seven bits.
Here is the way to adjust the width when it is the only problem. Tell the computer that the print line is wider than 80 characters with this WIDTH statement: WIDTH "LPTl:", 255 The 255 is a special number that prevents the computer system from inserting a CR-LF into the line-unless, of course, there’s one in your program.
brush or cloth, and never use alcohol or a thinner to clean the printer because it could damage the print head and the case. Do not spray the inside of the printer with oil: unsuitable oils can damage the mechanism. If lubrication is needed, call the toll-free Epson number: 1-800421-5426.
Figure C-1. Releasing the print head lock levers 6. Lift the print head from its position and carefully disconnect the flat cable from the print head, as shown in Figure C-2.
Figure C-2. Disconnecting the cable 7. Connect the new print head to the flat cable, and place the new print head in the head mount, as shown in Figure C-3.
Figure C-3. lnstalling the new print head 8. Move the head lock levers back to their original positions. Now your new print head is ready to use. Problem Solving and Maintenance C-13.
Appendix D Defaults and DIP Switches This appendix lists the default settings and lists and explains the settings of all the DIP switches. Default and Initialization Settings The Apex80 can be initial.
DIP Switch Settings The Apex80 has twelve DIP (Dual In-line Package) switches that allow you to change many of the printer’s settings to suit your individual needs. The DIP switches are in two groups, mounted on the back panel, as shown in Figure D-1.
The following tables describe the switches and their functions. The first two tables summarize the two groups of switches. The remaining table shows how to set the DIP switches for the available international character sets.
The DIP switch settings to select the different character sets are shown in Table D-3. Table D-3. Internatinal settings D-4 Defaults and DIP Switches.
Appendix E Choosing and Setting Up Optional Interfaces This appendix contains information on Epson interfaces compatible with the Apex80 printer, instructions on choosing the right interface for a particular job, and instructions for installing internally mounted interface boards.
Installing an Interface Before installing an interface, you must remove the printer’s cover. WARNING Do not remove the cover unless the printer is turned OFF and disconnected because high voltages are present inside the printer when the power is on.
Figure E-1. Removing the cover 6. Slightly raise the upper case by its front. As you do this, be careful not to pull the flat cable out of the control panel in the upper case.
7. Disconnect the other end of the flat control panel cable from the main circuit board connector. See Figure E-2. Figure E-2. Disconnecting the control panel cable After you remove the case, follow the instructions below to insert the interface board.
Inserting the interface board 1. Locate the connector cover at the back of the upper case, shown in Figure E-3. Push it down and in, toward the inside of the printer, until it clicks. You need to move the cover to allow access to the new interface connector when the case is reassembled.
3. 4. Plug the interface board into the connector marked CN2 on the main circuit board of the printer. Secure the board to the three supports with the screws provided, as shown in Figure E-5.
5. Connect the frame ground wire to the FG terminal tag on the interface board, as shown in Figure E-6. Figure E-6. Connecting ground wire to FG terminal tag 6. Reassemble the printer, reversing the procedure described in steps 2 through 7 in the previous section.
Serial Interface Settings If you are using an optional serial interface, you may need to change the communications protocol of the printer or the computer for them to communicate properly.
Appendix F Technical Specifications This appendix contains the specifications for the Apex80, including the built-in parallel interface. Printing Printing method Impact dot matrix Printing speed 180 c.
Mechanical Ribbon Cartridge, black #8750 (uses the same ribbon as the Epson LX-800 and FX printers) Life expectancy (in characters, at 14 dots/character): 3 million MCBF 3 million lines (excluding the print head) MTBF 4,000 hours Print head life 200 million strokes per needle Dimensions and Weight Height (excluding tractor): 3.
Environment Temperature Operation: 41° F to 95° F (5 C° to 35 C°) Storage: -22° F to 149° F (-30 C° to 60 C°) Humidity Operation: 10% to 80% without condensation Storage: 5% to 85% without condensation Shock Operation: Up to 1 G within 1 ms Storage: Up to 2 G within 1 ms Vibration Operation: Up to 0.
Table F-1. Pins and signals continual Notes: 1. The column heading “Direction” refers to the direction of signal flow as viewed from the printer. F-4 Technical Specifications.
2. “Return” denotes the twisted-pair return, to be connected at signal ground level. For the interface wiring, be sure to use a twisted-pair cable for each signal and to complete the connection on the return side.
Table F-2. Printing enabled/disabled signals and control conditions On Line (Indicator on) SLCT IN DC1/DC3 (Data on/off contr.) ERROR BUSY ACKNLG ON LINE LOW DC1 /DC3 (S W . 2-1/interface) (no effect) HIGH HIGH/LOW PULSED EA. CHAR. ON LINE HIGH DC1 RECV’D HIGH HIGH/LOW PULSED EA.
Index Command descriptions are not indexed here. For page references for specific commands, see pages A-4—6 or the Quick Reference card. A American Standard Code for Information Interchange, 2-2 ASCII, 2-2 AUTO LOAD, 1-17—19, 1-21 Automatic paper loading, 1-17—19 B BASIC, 2-6—7 Baud rate.
F Foreign language characters. See International character sets FORM FEED button, 1-21 G Graphics, 2-6,6-1—12 H Head. See Print head Hexadecimal, 2-2—3 I Indicator lights, 1-20 Initialization, D-1 Interface board, 1-2.
S Sans Serif, 1-21,4-1 SelecType, 3-1—4 Self test, 1-21—22 Serial interface. See Interfaces, optional Service. See Toll-free number Single-sheet paper, 1-15—19 Software commands.
.
Commands by Function The following list of commands is in the order used in the Command Summary (Appendix A). To find details of the command you want to use, refer to the page number in the right column.
DIP Switch Setting s Table 1. DIP switch group 1 Table 3. International settings Switch Function Action Action number when ON when OFF 1-1 Select condensed or normal Condensed Normal characters 1-2 Se.
Setting up Printer Features Graphics User-defined Characters EPSON AMERICA, INC. 2780 Lomita Boulevard Torrance, California 90505 Printed in Japan 87.08-20.
An important point after buying a device Epson Apex-80 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Epson Apex-80 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Epson Apex-80 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Epson Apex-80 you will learn all the available features of the product, as well as information on its operation. The information that you get Epson Apex-80 will certainly help you make a decision on the purchase.
If you already are a holder of Epson Apex-80, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Epson Apex-80.
However, one of the most important roles played by the user manual is to help in solving problems with Epson Apex-80. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Epson Apex-80 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
