Instruction/ maintenance manual of the product EN9250 Envision Peripherals
Go to page of 25
EN9250 EN9250 19” LCD Monitor User’s Manual By Envision Peripher als, Inc. www. ENVISION display .com.
EN9250 1 TA BLE OF CONTENTS Ta ble of Contents 1 For Your Sa fety 2 Precaut ions 3 General Notes 4-5 Before Y ou O perate T he M onitor 6 Installation Instru ctions 7-13 Operati ng Instructions 14-18 .
EN9250 2 FOR YOUR SA FETY Before operating the monitor, please read this manual thoroughly . T his manual should be r etained for fut ure ref erence. FCC Clas s B Radio Frequen cy Interferen ce Statem.
EN9250 3 ! Do not use the monitor near water , e.g. near a bathtub, washbow l, k itchen sink, laundry tub, sw imming pool or in a w et basement. ! Do not pla c e the monitor on an unstable car t, stand, or table. If the monitor falls, it can injure a person and c ause serious damage to the appliance.
EN9250 4 GENERA L NOTES The follow ing symptoms are normal with LCD monitor and do not indicate a problem. • • • • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Pow er Sw itch and then turn it on again to make sure the flicker disappea rs.
EN9250 5 GENERA L NOTES (cont) • • • • Plu g & Play DDC 2B Feat ure - Thi s monitor is equipped with VESA DDC 2B capabilities according to the VESA DDC STANDAR D. It all ow s the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additi onal information about its display capabilities.
EN9250 6 BEFORE Y OU OPERA TE THE MONITOR • 19” (48cm) T FT Color LC D M onitor • Crisp & Clear D is play for W indow s • Recommended R es olutions: 1280 X 1024 @ 60Hz • E P A E NERGY S .
EN9250 7 7 INS TA LLA TION INSTRUCT IONS INSTALLING & REMOVING THE BA SE In st all Figure 1 - Ins talling the Base. INSTAL LI NG THE B AS E 1. Set the bottom base on a flat surface . 2. Line up the front of the moni tor w ith the front o f the base and press firmly.
EN9250 8 INSTA LLA TION INSTRUCTIONS (Cont) POW ERC OR D Pow er Sou rce: 1. M ake sure that the pow er cord is the correct ty pe required in your ar ea. 2. Th is LCD monito r h as an internal Universal Power Supply that a llow s operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is require d.
EN9250 9 INS T A LLA TION INSTRUCTIONS (Cont) Conn ect ing T he C ables Figure 2 Conn ec ting Cables 1. AC Pow er Cord 2. 15-pin D-S UB Cable 3. D VI Cable 4. Audi o Cable Turn o ff your computer before per forming the procedure b elow . 1. Connect the female e nd of the AC pow er cord to the AC-in p o rt on the back of the monitor.
EN9250 1 0 INS T A LLA TION INSTRUCTIONS (con t) How T o Insta ll The INF & ICM Files • • • • Th is is a Plug & Play monitor. Mi crosoft W indows wil l automatically install a Plug & Play drive r for it when you first install this monitor.
EN9250 1 1 INS T A LLA TION INSTRUCTIONS (con t) Heig ht , T ilt , Piv o t & Sw iv el Adjustme nt Your monitor features a multi-adjustable stand that wil l enable it move 110mm up/dow n (height ad.
EN9250 1 2 INS T A LLA TION INSTRUCTIONS (cont) Pre paring To Ins tall The Optional Wa ll M ount A rm (Not Inc luded) This monitor can be attached to a wall mounting arm y ou can purchase separately. Tur n the pow er OFF then dis-connect the cables from the monitor befo re performing the pr oc edure belo w.
EN9250 1 3 INS T A LLA TION INSTRUCTIONS (cont) A ttaching The Optiona l Wall Mount A rm (not suppli ed) Follow these steps to finish installing the w all mounting arm: 1. Place the w all mounting arm onto the back of the monitor. Line up the holes of the ar m wi th the holes in the back of the moni tor.
EN9250 1 4 OPERA TING IN STRUCTIONS EXTERNA L CONTROLS Figure 4 - Ex ternal Controls 1. Power Button 4. > or Volum e 2. LED 5. < o r Volum e 3. ME NU / ENT ER Button 6. A uto Adj us t / Ex it Bu tton • Pow er Button: Press this button to turn the monitor O N or OFF.
EN9250 1 5 OPERA TING INSTRUCTIONS (cont) • Auto Adjust bu tt on / Exi t: 1. W hen OSD menu is in active status, this button will act as EXIT- KEY (EX IT OSD menu) or go back to the prev ious menu. 2. W hen OSD menu is in off status, press this button for 2 seconds to activate the Auto A djustment function.
EN9250 1 6 OPERA TING INSTRUCTIONS (cont) How To A djust A Se tting 1. Press the M ENU-button to activate the OSD win dow ( Figure 4) . 2. Press < or > to nav igate through the functions. On c e the desired function is highlighted, press the M ENU-button to activate it.
EN9250 1 7 OPERA TING INSTRUCTIONS (cont) The descriptions for function control LEDS Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description Reset Value Contrast Contrast from Digital-r egister.
EN9250 1 8 H. Position Adjust the horiz ontal position of the OSD. 50 V. Position Adjust the vertical position of the OSD . 50 OSD Setup OSD Ti meout Adjust the OSD timeout. 10 English N/A Set O SD display language to English. Deutsch N/A Set OS D display language to German.
EN9250 1 9 TECHNIC A L SUPPORT (FA Q) Problem & Question Possible Solution Pow er LED is not on *Ch ec k if the Power Switch is in the ON position *Pow er C ord should be connected No Plug & P.
EN9250 2 0 TECHNICA L S UPP ORT (FA Q) (cont) CLOC K (pix el frequency) controls the number of pix els scanned by one horizo ntal s w eep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct w idth. FOCUS adjusts the phase of the pix el clock signal.
EN9250 2 1 A PPENDIX SPECIF ICATIO NS Size 48cm(19.0") LCD Pane Input V-Freque nc y 55-75Hz Display Colors 16.7M Colors Dot Clock 135M Hz M a x . Resolution 1280 x 1024 @75H z Plug & Play VESA DDC 2B TM ON M ode ! 55W EPA E NERGY S TAR ® OFF M ode ! 2W D-Sub 1 5pin Input Connector DVI-D 24pin Analog:0.
EN9250 2 2 A PPEN DIX ( con t) Switc h • Auto Adjust Ke y/Exit • < /Volum e • > / Volum e • Pow er Button • ME NU/ Enter Ex ternal Controls: Functions • Contrast • Br ightness • Focus • Clock • H.
EN9250 2 3 A PPEN DIX ( con t) Preset Disp lay M od es STANDA RD RESOLU TION HORI Z ONTA L FREQUENCY (KHZ) VERTIC AL FREQUEN CY(HZ) 640 × 480 31.469 59.940 VGA 640 × 480 37.500 75.000 800 × 600 37.879 60.317 SVGA 800 × 600 46.875 75.000 1024 × 768 48.
EN9250 2 4 A PPEN DIX ( con t) Connector Pin A ssi gnment 15 6 10 11 15 15 - Pin Color Display Sign al Cable PIN NO. DESCRIPT ION PI N NO. DESCRIPT ION 1. Red 9. NC 2. Gr een 10. Logic Gr ound 3. Blue 11. M onitor Ground 4. M onitor Ground 12. DDC- Serial Data ` DDC-re turn 13.
An important point after buying a device Envision Peripherals EN9250 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Envision Peripherals EN9250 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Envision Peripherals EN9250 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Envision Peripherals EN9250 you will learn all the available features of the product, as well as information on its operation. The information that you get Envision Peripherals EN9250 will certainly help you make a decision on the purchase.
If you already are a holder of Envision Peripherals EN9250, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Envision Peripherals EN9250.
However, one of the most important roles played by the user manual is to help in solving problems with Envision Peripherals EN9250. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Envision Peripherals EN9250 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
