Instruction/ maintenance manual of the product EP3 Enviro
Go to page of 14
PLEA SE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE SHERWOOD INDUSTRIES IS AN ENVIRONMENT ALL Y RESPONSIBLE COMP ANY . THIS MANUAL IS PRINTED ON RECYCLED P APER. 6 50-1070 PELLET STOVE EF3 O WNER ’S MANU AL PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET BURNING ROOM HEATER.
T able of Contents 2 Introduction..............................................................................................................3 Rating Label Location.....................................................................................
3 Introduction * This manual is designed for the home owner in conjunction with the technical manual. * R ATING L ABEL L OCATION : Freestanding: The r ating label is located on the inside of the hopper lid. Fireplace Insert and Built -In Heater: The r ating label is located on the hopper cover .
4 I MPORTANT S AFETY D ATA : Please read this entire Owner’s Manual before installing or operating your ENVIRO Pellet Stove. Failure to follow these instructions may result in property damage, bodily injury or even death.
5 Introduction ASHES: Disposed ashes should be placed in a metal container with a tight-fit ting lid. The closed container of ashes should be on a non-combustible floor on the ground, well away from all combustible materials pending final disposal.
Oper a ting Instructions A UTOMATIC S AFETY F EATURES : Y our pellet Stove has the following saf ety featur es: A. The stove will shut off when the fire goes out and the exhaust temperature drops below 120°F (49°C). B. The stove has a high temperature safety switch.
Oper a ting Instructions Figure 3: Dial-A-Fire control panel. 1. Check and fill hopper with pellets. 2. Make sure unit is plugged into a working outlet. 3. Switch the power “ON” by pushing the start-up switch once only . 4. T urn knob “B” to the 12 o’clock position.
Auger T rim Auger T rim Auger T rim 2 Seconds "ON" 3 Seconds "ON" Factory Setting 4 Seconds "ON" 8 AUGER TRIM F AN MAN UAL FEED ON/OFF HEA T LEVE L 3. AUGER PULSE LIGHT: This light will flash in conjunction with the auger .
9 Oper a ting Instructions O PERATING Y OUR P ELLET S TOVE - C IRCUIT B OARD : PRE-BURN INSTRUCTIONS : The burn pot liner holes must be clear and the liner installed properly against the ignitor tube for proper oper ation. Check the hopper for enough pellets to start the unit.
10 R outine Cleaning and Maintenance NOTE: Do not use abrasiv e cleaners to clean the surface or any part of the sto ve. The following should be inspected periodically to ensure that the appliance is .
11 ASH PAN (2-3 days) Monitor the ash lev el every week. Remember that different pellet f uels wil l have different ash contents. Ash content is a good indication of fuel efficiency and quality . Refer to “W arnings and Recommendations” for disposal of ashes.
12 Installation of firebox backing: • Install the side panels in place. Insert center panel, hold the panels in place • Install the top rod by sliding it into one side panel then across into the other panel. S cr ew rod in place. • Re-install steel brick liner and screw in place.
13 W arr anty Sherwood Industries Ltd. gives a five year limited warrant y on all steel manuf actured parts. A one-year warr anty is pr ovided on all electrical components.
14 The following information must be recorded by the installer for w arrant y purposes and future r eference. NAME OF OWNER: _________________________________________ ADDRESS: ________________________.
An important point after buying a device Enviro EP3 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Enviro EP3 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Enviro EP3 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Enviro EP3 you will learn all the available features of the product, as well as information on its operation. The information that you get Enviro EP3 will certainly help you make a decision on the purchase.
If you already are a holder of Enviro EP3, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Enviro EP3.
However, one of the most important roles played by the user manual is to help in solving problems with Enviro EP3. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Enviro EP3 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
