Instruction/ maintenance manual of the product EG40-071 Enviro
Go to page of 23
SHERWOOD INDUSTRIES IS AN ENVIRONMENT ALL Y RESPONSIBLE COMP ANY . THIS MANUAL IS PRINTED ON RECYCLED P APER. BY: SHERWOOD INDUSTRIES LTD O WNER ’S MANU AL PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE .
FOR SAFE INST ALLA TION AND OPERA TION OF Y OUR “ENVIRO” HEA TER, PLEASE CAREFULL Y READ THE FOLLOWING INFORMA TION: • All ENVIRO gas-red appliances must be installed in accor dance with their instructions. Caref ully r ead all the instructions in this manual rst.
T able of Contents 3 Safety Precautions..........................................................................................2 T able of Contents...........................................................................................3 Codes And Approv als.
BV: This V ented appliance draws all of its combustion air from the dwelling and must be vented using listed B or L vent. May also be v ented through a conv entional chimney using a chimney liner kit. This appliance has been tested and approved f or installations from 0 feet to 2000 feet (610 m) above sea level.
5 WARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon monoxide (CO) poisoning and possible death.
Initial Inst alla tion QUALIFIED INST ALLERS ONL Y V ENTING : This model must have a v ent opening in the rear of the unit. Conrm this and also check that the label on the right side panel door states “V ented Room Heater” . WARNING: This appliance has been designed to operate by dr awing combustion air and dilution air from the room.
Initial Inst alla tion QUALIFIED INST ALLERS ONL Y T ERMINATION : 7 .
8 Initial Inst alla tion QUALIFIED INST ALLERS ONL Y S TRAIGHT V ERTICAL I NSTALLATION : Figure 5: Straight vertical installation. This basic venting conguration shown ar e rough guidelines only . Follow national and local codes for other installation options.
9 Initial Inst alla tion QUALIFIED INST ALLERS ONL Y E LECTRICAL R EQUIREMENTS : The ENVIRO EG40 will operate without electrical power . This model has a millivolt gas control, which uses the pilot ame to generate enough electricity to operate the main burners.
A DJUSTING T HE V ENTURIES : • There is a separate v enturies for each burner , see Figure 9. • R emove one screw from the cov er plate located below the ash shelf and loosen the other screw (do not remove) swing the cover plate out of the way and tighten screw down to hold it in place.
11 Initial Inst alla tion F UEL C ONVERSION : WARNING: This conversion kit shall be installed by a qualied service technician in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction.
Initial Inst alla tion G AS L INE C ONNECTION AND T ESTING : WARNING: Only persons licensed to work wi th gas piping may make the necessary gas connections to this appliance. GAS LINE CONNECTION • This stove is equipped with a certied exible pipe located on the right side of the unit terminating in a ” male NPT tting.
13 Second ar y Inst alla tion I NSTALLATION OF L OG S ET AND E MBERS : CAUTION: Use only the type of ember material supplied with this appliance. Due to the irregular size of the ember material there may be more than required. The use of other foreign materials on the burners may create dangerous conditions.
Second ar y Inst alla tion CAUTION: NEVER OPERATE THIS APPLIANCE WITH THE GLASS DOOR REMOVED. 4. Upon the rst light up, watch for ignition to ALL burner ports. If a long delay is noted: First, w ait for the appliance to cool down. • Open the front door of the appliance.
Oper a ting Instructions FOR YOUR SAFETY READ COMPLETELY BEFORE OPERATING. WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OR LIFE. A) This appliance is equipped with a pilot that must be lit by hand by following these instructions exactly .
16 R outine Maintenance and Ser vice Annually check to ensure that your V enting system is clear . Periodically check the pilot and burner . Check to see that all the burner ports are clean and clear . Check the pilot head for blockage. Check to ensure the pilot ame is blue with no or very small yellow tips.
T rouble Shooting Problem Possible Cause Solution Spark will not light the pilot after repeatedly pressing the spark ignitor Defective piezo ignitor . • Check connections to ignitor . • If ignitor connections are good but there is no spark; replace ignitor .
P ar ts List Reference Number Part Description Part Number 1 120 °F (49 °C) Ceramic T emperature Sensor EC-001 2 220 °F (104 °C) Ceramic Spill Switch EC-002 3 S.
19 P ar ts List Reference Number Part Description Part Number BV Owner ’s Manual EG40-071 14 Pedestal EG40-080 15 Side Panel EG40-086 16 BV Stove T op EG40-087 Firebox Bafe EG40-088 Stove T op Ba.
P ar ts Diagr am - Chas sis EG 40 Body (Chassis) July 2004 20.
21 P ar ts Diagr am - Gas T r a y & Door EG40 Gas Tray & Door Assemblies July 2004 28 9 21 10 24 3 5 6 11 7 12 17 27 26 25 4.
W arr anty Sherwood Industries Ltd. offers a Limited Lifetime W arrant y on this gas product. This limited lifetime warr anty covers the appliance for a period of seven years from the date of installation.
23 Inst alla tion Da t a Sheet The following information must be r ecorded by the installer for warr anty purposes and future reference. NAME OF OWNER: _________________________________________ ADDRES.
An important point after buying a device Enviro EG40-071 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Enviro EG40-071 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Enviro EG40-071 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Enviro EG40-071 you will learn all the available features of the product, as well as information on its operation. The information that you get Enviro EG40-071 will certainly help you make a decision on the purchase.
If you already are a holder of Enviro EG40-071, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Enviro EG40-071.
However, one of the most important roles played by the user manual is to help in solving problems with Enviro EG40-071. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Enviro EG40-071 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
