Instruction/ maintenance manual of the product C-11256 Enviro
Go to page of 16
PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET-BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH. Contact your building or fire officials about restrictions and installation inspection requirements in your area.
T able of Contents 2 Introduction........................................................................................3 Rating Label Location................................................................3 Fuel Quality ............................
3 Introduction * This manual is designed for the home owner in conjunction with the technical manual. * R ATING L ABEL L OCATION : The rating label is located on the inside of the hopper .
4 Safety W arnings & R ecommend a tions Please read this entire Owner’s Manual before installing or operating your Enviro Pellet Stove. Failure to follow these instructions may result in property damage, bodily injury or even death.
5 Safety W arnings & R ecommend a tions ELECTRICAL: The use of a surge protected power bar is recommended. The unit must be grounded. The grounded electrical cord should be connected to a standard 110-120 volts (4.2 Amps), 60 hertz electrical outlet and also must be accessible.
21 13 / 16 " (554mm) 15 15 / 16 " (404mm) 22 1 / 16 " (561mm) 41 15 / 16 " (1065mm) 42 1 / 2 " (1080mm) 23 13 / 16 " (605mm) 26 1 / 8 " (664mm) 26 3 / 8 " (669mm) 24 3 / 16 " (615mm) Oper a ting Instructions D IMENSIONS & S PECIFICATIONS : Figure 1: Dimensions of Omega.
7 Oper a ting Instructions C ONTROL B OARD F UNCTIONS : 1. ON/OFF BUTTON: Used to turn the unit ON and OFF manually . 2. FUEL TYPE BUTTON: Used to swi tch between fuel type modes; Pellet (for all qual.
PRE-BURN CHECK : The burn pot liner holes must be clear and the liner installed properly against the ignitor tube and locked in place. Check the hopper f or enough pellets to start the unit. Note: Fuel T ype can only be changed when the unit is cold. The thermostat mode can be changed during normal operation.
9 the fire. • A tall, lazy flame with dark orange tips requires more air – Open slider (pull out) slightly . • A short, brisk flame, like a blowtorch, has too much air – Close slider (push in) slightly .
R outine Cleaning and Maintenance The following list of components should be inspected and maintained routinely to ensure that the appliance is operating at its optimum and giving you excellent heat value. The appliance, flue gas connector and the chimney flue require regular cleaning.
Figure 9: Omega Burn Heat Exchanger Cleaning. 11 R outine Cleaning and Maintenance HEAT EXCHANGER TUBES (W eekly) There are two (2) sets of exchanger tube scrapers; the handles are located under the top grill (trivet).
R outine Cleaning and Maintenance EXHAUST PASSAGES (Biannually) 1. Open the firebox door by lifting the handle. 2. Remo ve the burn pot assembly and clean all the parts. 3. Lubricate all screws with penetrating oil. 4. Using a ” socket, remove the two (2) bolts that hold the firebox liner in place.
13 W arr anty Sherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood Industries, our commitment to the highest level of quality and customer service is the most important thing we do.
W arr anty Exclusions and Limitations: 1. This W arrant y does not cover tarnish, discolor ation or wear on the plating or paint. 2. This W arrant y excludes wear and tear or breakage caused by cleaning, mo ving or service on log set. 3. A qualified installer must install this stove or fireplace.
15 W arr anty 17 . Damage to plated surfaces caused by fingerprints, scratches, melted items, or other external scores and residues left on the plated surfaces fr om the use of abrasiv e cleaners or polishes is not covered in this warr anty . 18. The Limited W arr anty does not cover tarnish, discolor ation or wear on the plated surfaces.
16 NAME OF OWNER: _________________________________________ ADDRESS: _________________________________________ _________________________________________ _________________________________________ PHONE.
An important point after buying a device Enviro C-11256 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Enviro C-11256 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Enviro C-11256 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Enviro C-11256 you will learn all the available features of the product, as well as information on its operation. The information that you get Enviro C-11256 will certainly help you make a decision on the purchase.
If you already are a holder of Enviro C-11256, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Enviro C-11256.
However, one of the most important roles played by the user manual is to help in solving problems with Enviro C-11256. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Enviro C-11256 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
