Instruction/ maintenance manual of the product XSR-3150 Enterasys Networks
Go to page of 110
X-Pedition ™ Security Router XSR-3150 Getting Started Guide V ersion 3.0 P/N 9033865-06 8.5x11-inch cover with bleed on 4 sides.
.
i Notice Enterasys Networks reserv es the right to make changes in s pecifications and other information contained in this document and its web site without prior notic e.
ii Regulatory Compliance Information Federal Communications Commiss ion (FCC) Notice The XSR complies with Title 47, Par t 15, Class A of FCC rules.
iii Industry Canada Notices This digital apparatus does not exceed the class A limits for radio noise emissions from di gital apparatus set out in the Radio Interfer ence Regulations of the Canadian Department of Communications.
iv Product Safety This product complies with the following: UL 60950, CSA C22.2 No. 60950, 73/23/EEC, EN 60950, EN 60825, IEC 60950.
v ѻ ѻ ક䇈ᯢк䰘ӊ Supplement to Product Instructions ᳝↦᳝ᆇ⠽䋼ܗ㋴ (Hazardous Substance) 䚼ӊৡ⿄ (Parts) 䪙 3E ∲ +J 䬝 &G ݁Ӌ䫀 .
vi VCCI Notice This is a class A product based on the standard of the V oluntary Control Council for Interference by Information Te c h n o l o g y Equipment (VCCI) V ‐ 3.
vii Australian T elecom WA R N I N G : Do not install phone line connections during an el ectrical storm. WA R N I N G : Do not connect phone line until the inte rface has been configured through loc al management.
viii E nterasys N etworks , I nc . F irmware L icense A greement BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT. This document is an agreemen t (“ Agreement” ) betw een the end user (“Y ou”) and Enterasys Networks, Inc.
ix If the Program is exported from the United Stat es pursuant to the License Exce ption TSR unde r the U.
x 11. ASSIGNMENT. You may not assign, transfer or sublicense this Agreement or any of Your rights or obligations under this Agre.
xi Contents About This Guide Contents of the Guide ..... .................... ................... .................... ................ ................... ...... .................... .......... xv Conventions Used in This Guid e ........... .........
xii PRI Configuration ......... ................ ................... .................... ................... ................ .......... ...................... .. 3-8 BRI Configuration ......... ................ ................... ..................
xiii bU ............. ................ .................... ................... ................ .................... ................... . ............ ................... 3-37 cd ................. ................ ................... ...............
xiv.
xv About This Guide This guide provides a general ov erview of the XSR ‐ 3150 hardware and softw are features and describes how to quickly install and configure the XSR.
xvi Electrical Hazard : W arns against an action that could result in persona l injury or death due to an electrical hazard. Riesgo Electric o: Advierte contra una acción que pudiera re sultar en lesión corporal o la muerte debido a un riesgo eléctrico.
xvii Getting Help For additional support related to the XSR, contact Enterasys Netw orks using one of the following methods: Before cont.
xviii.
XSR Getting Started Guide 1-1 1 Overview This chapter introduces the key features of the XSR-3150 and briefly describes har dware installation. System Description The XSR is a networking device designed for enterp rise r egional offices that provides IP routing over GigabitEthe rnet LAN and T1/E1, Se rial (RS 232, X.
System Description 1-2 Overview Figure 1-1 T ypical XSR-3150 T opology Hardware Features The semi-modular XSR, shown in Figure 1-2 , comes equipped with the following featur es: • Standard 1U chassis (1-1 1/16 inches high by 17 in ches wide by 21 inches deep) mountable in a standard 19” rack.
System Description XSR Getting Started Guide 1-3 Figure 1-2 XSR-3150 • T wo Network Interface Module (NIM) card slots for these NIMs: – 1, 2, or 4 full, fractional and channelize d T1/E1 W AN NIM with integral CSU/DSU or Primary Rate Interface (PRI) ports (RJ-48C).
System Description 1-4 Overview • 14 diagnostic LEDs to displ ay port and system st atus as well as indicate a Flash upgrade in progr ess. • Five system fans with failur e detection capabili ty and three i n-board fans ded icated to power supply cooling.
System Description XSR Getting Started Guide 1-5 • Simple Network T ime Protocol (SNTP) server •O S f a l l b a c k IP Routing • Static and multipl e routes to the same dest ination • Redistri.
System Description 1-6 Overview Security • Stateful inspection firewall e ngine • F TP , H.323, and RPC (SUN and Microsoft) ALG support • Application commands for F TP , SMTP , & HTTP • Fi.
System Description XSR Getting Started Guide 1-7 • Periodic Keep-Alive message s to learn of connection problems • Multi-pr otocol interconnect over Frame Relay - RFC-2427 • RFC-2390 Frame Relay.
System Description 1-8 Overview • Bandwidth optimization (BoD) & Dial on Demand (DoD) • Bandwidth Allocation Protocol (BAP) • Security: P AP/CHAP • Call monitoring • Multili nk PPP (MLPP.
System Description XSR Getting Started Guide 1-9 Certificates (embedded/smart cards) – Micr osoft only •E n c r y p t i o n • Advanced Encryption Standar d (AES), T rip le Data Encryption Standa.
System Description 1-10 Overview Asynchronous Digit al S ubscriber Line (ADSL) • POTS and ISDN circuit support • A TM Frame UN I (FUNI) data framing format • OAM cells: AI S, RDI, CC, Loopback o.
Installation Overview XSR Getting Started Guide 1-11 • Switched PPP Multilink connections • Backup using ISDN & MLPPP connections • Dialer interface spoofing • Dialer watch Inst allation Overview Installing the XSR consists of performing the fo llowing general steps.
Installation Overview 1-12 Overview.
XSR Getting Started Guide 2-1 2 Hardware Installation Introduction This chapter provides a checklist to verify your shipment, suggestions for the installation si te, and describes how to instal l the .
Installing NIM Cards and Rack Mounting 2-2 Hardware Installation • Each XSR AC power supply requires a th ree-pr onged power receptacle capable of delivering the current and voltage specified in Appendix A .
Installing NIM Cards and Rack Mounting XSR Getting Started Guide 2-3 4. Remove the NIM slot cover , as shown in Figur e 2-2 , by grasping the handle and pr essing it to the side before pulling it out.
Installing NIM Cards and Rack Mounting 2-4 Hardware Installation 7. Attach the rack brackets to the chassi s with the scr ews supplied, as shown in Fi gure 2-4 . Figure 2-4 Fastening Rack Bracket s 8. Mount the bracketed XSR to your rack, as shown in Figur e 2-5 .
Installing a CompactFlash Memory Card XSR Getting Started Guide 2-5 Inst alling a Comp actFlash Memory Card An optional CompactFlash (CF) memory card provides additional non-volatile storage capabilities in 8, 16, 32, or 64 Mbyte increments.
Installing a CompactFlash Memory Card 2-6 Hardware Installation Gently insert the CF into the sl ot, taking care that the CF’s wider gr ooved edge fits into the wider track of the PCMCIA interfa ce. If the car d does not seat easily but stops halfway i nto the slot, do not force it in - the card was inserted in corr ectly .
Connecting Cables XSR Getting Started Guide 2-7 Connecting Cables Perform any of the following steps to connect your cabling to optional W AN or LAN NIM s, GigabitEthernet ports, and power supplies: 1. Connect the serial COM cable pro vided in the packing box to your P C connector , as shown in Figur e 2-9 .
Connecting Cables 2-8 Hardware Installation Figure 2-1 1 Connecting High Speed Ser ial Connector Figure 2-12 Att aching T3/E3 BNC Connectors NIM 1 NIM 2 SECURITY ROUTERS XSR-3150 NIM 1 NIM 2 SECURITY .
Connecting Cables XSR Getting Started Guide 2-9 Figure 2-13 Connecting ADSL Connector A CompactFlash card is provided with the XSR ADSL NIM. It is loaded with the Digi tal Signal Processing (DSP) firmware ( adsl.fls ) r equired to communicate with your DSLAM.
Connecting Cables 2-10 Hardware Installation 3. Connect the Ethernet port(s) to your LAN connectors with a cable, as shown in Figure 2-15 . Figure 2-15 Att aching GigabitEtherne t Connector 4. Insert the Mini-GBIC module in the GBIC slot then connect the optical cable, as shown in Figure 2- 16 .
Connecting Cables XSR Getting Started Guide 2-11 5. Attach either the Ethernet or Fi ber E thernet LAN NIM, as shown in Fig ure 2-17 and Figure 2- 18 , respectively .
Connecting Cables 2-12 Hardware Installation 6. Attach the dual power supply cords to the conne ctors at the re ar of the XSR, as shown in Figure 2- 19 , and plug in the country-specific power co rds to a wall socket.
XSR Getting Started Guide 3-1 3 Software Configuration This chapter describes how to init ializ e, quickly set up and verify your configurati on for the XSR. Refer to the XSR CLI Referenc e Guide for a more thor ough explanation of commands and parameter options.
Initializing XSR Software 3-2 Software Configuration • ETH 10/100/1000 LEDs tu rn ON and OFF a fe w times during initialization as the XSR pro ce ed s f rom bo ot rom to po we r u p d ia gn os ti cs to sof tw are im a ge, th en th ey rem ai n O N o r OFF depending on the LA N type.
Opening a COM (Console) Session XSR Getting Started Guide 3-3 only the first error will be r eported, along with a count of the sum of errors incurr ed. In the case of a single error , only the error line will be rep or te d. Er ror me ss ag es wi ll b e l og ge d a s well.
Optional: Configuring Remote Auto In stall 3-4 Software Configuration Note the use of a helper-address to specify a destination address for UDP br oadcasts and forward traffic to the DNS and TF TP servers. In the example below , DNS and TF TP servers reside o n the same node - 10.
Optional: Configuring Remote Auto Install XSR Getting Started Guide 3-5 + TFTP transfer succeeded in copy ing the hostname file to the Flash: startup-config file.
Optional: Configuring Remote Auto In stall 3-6 Software Configuration + Creates a VPDN session group and links it to a virtual template. accept-dialin protocol pppoe virtual-template 1 pppoe limit per-mac 10 + This is an optional command. pppoe limit max-sessions 320 00 + This is an optional command.
Configuring the XSR Name and User Information XSR Getting Started Guide 3-7 Phase 3 - ADSL - trying to c onnect on 0/35 with snap PPPoE + PVC 0/35 is found, SNAP PPPoE encapsulation is applied and authentication tried if required. Phase 3 - ADSL - waiting for IP to connect (54 sec) + The XSR waits one minute for the PPPoE connection to come up.
Configuring the LAN Ports 3-8 Software Configuration Enter the following command to conf igure the XSR as an SNTP client: XSR(config)#sntp-client serv er [primary | A.B.C.D.][alternate | A.B.C.D.] Enter the following command to configure the XSR as an SNTP server: XSR(config)#sntp-server enab le Remember to save your conf iguration after all edits.
Configuring the WAN Ports XSR Getting Started Guide 3-9 This command allows multiple l ogical W AN interf aces to be cr eated on a single channelized T1/E1/ISDN-PRI port, ranging from 0 - 23 for T1 lines, and 0 - 31 for E1 lines. Also, fr om 1 - 24 T1 and 1 - 31 E1 timeslots can be set.
Configuring the WAN Ports 3-10 Software Configuration 4. Enter encapsulation ppp to select PP P encoding. 5. Enter no shutdown to keep the BRI interface enabled. BRI Leased Frame Relay 1. Enter interface bri 0:<1 | 2>.<1-30> to ac quire BRI Interface mode and select the BRI port and channel 1 or 2.
Configuring the WAN Ports XSR Getting Started Guide 3-11 ADSL Configuration ADSL can be configur ed using three dif ferent ty pes of encapsulati on: PPPoA, PPPoE, and IPoA. Continue configuration with th e ADSL type of your choice. PPPoE The following commands configure a sample PPPoE topology .
Firewall Sample Configuration 3-12 Software Configuration The commands below configure the A TM interface an d sub-interface with a ne gotiated IP address, CHAP username and password, and bans keepalives. XSR(config)#interface ATM 0 XSR(config-if<ATM0/0>)#no sh utdown XSR(config-if<ATM0/0.
Firewall Sample Configuration XSR Getting Started Guide 3-13 Figure 3-1 XSR with Firewall T opology In this configuration , the firewall provides pr otected access from th e private to dmz networks. That is, access is restricted to W eb and mail traffic onl y .
Setting Up RIP Routing 3-14 Software Configuration XSR(config)#ip firewall filt er allowICMP private dmz protocol-id 1 XSR(config)#ip firewall filt er allowICMP private ANY_EXTERNAL protocol-id 1 XSR(.
Configure OSPF Routing XSR Getting Started Guide 3-15 10. Enter ip rip receive version < 1 | 2 > to allow a RIP version of updated transmissions. Accept both RIP V1 and V2 is the default value. 11 . E n t e r router rip to acquir e Router configuration mode and enable RIP r outing.
Setting Up an SNMP Community String, Traps and V3 Values 3-16 Software Configuration 5. Enter media-type V35 to match the corr ect cabling interface. The def ault media type for Frame Relay is RS-232. 6. Enter frame-relay traffic-shaping to enable congestion contr ol.
Configuring Message Logging and Severity Level XSR Getting Started Guide 3-17 5. Optional . For SNMPv3, enter snmp-server group < name > v3 { auth | nonauth | priv } read < name > write < name > to add a group. Groups of fer users authorization ch oices and read/write privileges.
Viewing Your Configuration 3-18 Software Configuration V iewing Y our Configuration 1. Enter show running-config to verify your current configuration. The XSR will display the co mmands you issued up to this point. Default values ar e not displayed. Connecting Remotely via the W eb 1.
Connecting Remotely via the Web XSR Getting Started Guide 3-19 Click on Pr oduct V ersion to bring up the Pr oduct V ersion window for a hos t of hardwar e, bootrom, and softwar e information as shown in Figure 3-3 . Figure 3-3 Web Pr oduct V ersion Window Product V ersion Copyright 2004 by Enterasys Networks, Inc.
LAN-PPP Services Sample Configuration 3-20 Software Configuration LAN-PPP Services Sample Configuration The sample configuration below , see Figur e 3-4 , creates a PPP , fractional T1 leased line connection from the XSR branch node to the Central Site router and a backup serial dial up link to the Backup Si t e re g io n a l ro u te r .
LAN-PPP Services Sample Configuration XSR Getting Started Guide 3-21 XSR(config-controller<T1-1/0 >)#no shutdown + Enables T1 controller XSR(config)#interface serial 1/0:0 + Configures Serial in.
Frame Relay WAN Link with PPP Backup Sample Configuration 3-22 Software Configuration Frame Relay W AN Link with PPP Backup Sample Configuration The sample configuration below , similar to the precedi.
Frame Relay WAN Link with PPP Backup Sample Configuration XSR Getting Started Guide 3-23 XSR(config-cmap<data_class>) #match access-group 133 + Assigns ACL 133 to this class map XSR(config)#poli.
Frame Relay WAN Link with PPP Backup Sample Configuration 3-24 Software Configuration XSR(config)#interface serial 1/0.2 multipoint + Configures FR port: Serial card in slot 1, port 0, s ub-in terface 2 for multipoint links and acquires Interface mode XSR(config-if<S1/0.
Frame Relay WAN Link with PPP Backup Sample Configuration XSR Getting Started Guide 3-25 Configure OSPF Routing XSR(config)#router ospf 1 + Enables OSPF with a router ID and acquires Router mode XSR(config-router)#network 1 92.168.1.0 0.0.0.255 area 0.
Frame Relay WAN Link with PPP Backup Sample Configuration 3-26 Software Configuration XSR(config-if<D1>)#encapsula tion ppp + Enables PPP encapsulation XSR(config-if<D1>)#ip addres s 192.
VPN Site-to-Site Sample Configuration XSR Getting Started Guide 3-27 VPN Site-to-Site Sample Configuration The following VPN topology , s hown in Figure 3-5 , configur es a central site XSR to connect over IPSec tunnels with a remote ANG-1 105 and two XSRs.
VPN Site-to-Site Sample Configuration 3-28 Software Configuration XSR(config)#access-list 101 permit udp ah any any XSR(config)#access-list 101 deny ip any any XSR(config)#access-list 190 permit ip any 112.16.72.0 0.0.0.255 XSR(config)#access-list 191 permit ip any 112.
VPN Site-to-Site Sample Configuration XSR Getting Started Guide 3-29 XSR(config)#crypto map acme 91 XSR(config-crypto-m)#set tra nsform-set esp-3des-sha XSR(config-crypto-m)#match a ddress 191 XSR(config-crypto-m)#set pee r 112.
VPN Sample Configuration with Network Extension Mode 3-30 Software Configuration Configuring Authentication (AAA) Configur e an AAA use r and DEF AUL T AAA group for r emote users. When an ANG tunnels into the XSR, it will be assigned dynamically to the IP pool AUTH .
VPN Sample Configuration with Network Extension Mode XSR Getting Started Guide 3-31 Generate the master key . Refer to the following sampl e key: XSR(config)#crypto key maste r generate New key is 217.
VPN Sample Configuration with Network Extension Mode 3-32 Software Configuration Create user(s), specify an IP from virtual subnet, and assign a password: XSR(config)#aaa user nem-tes t XSR(config)#pa.
XSR Rebooting Characteristics XSR Getting Started Guide 3-33 Create the multi-point VPN virtual port required to terminate many clients: XSR(config)#interface vpn1 m ulti-point XSR(config)#description “VPN Virtual Interface Int0” XSR(config)#ip address 10.
XSR Rebooting Characteristics 3-34 Software Configuration Testing S/W Integrity << PAS SED >> Loading Router S/W to addres s 0x80020000 Verifying uncompressed chksu m ... Starting from 0x80020000... Attaching shared memory obje cts at 0xa0000600.
Bootrom Monitor Mode Commands XSR Getting Started Guide 3-35 Reload Command from the CLI Y ou can reboot the XSR firmwar e by issuing the com mand reload <cold | warm> . Y ou are then prompted to confirm the command. Once the firmwa re is r eloaded, the configuration is loaded from the startup-config file.
Bootrom Monitor Mode Commands 3-36 Software Configuration All the commands in each group ca n be listed by entering the command gr oup letter . The main menu provides the following functions: • Rebo.
Bootrom Monitor Mode Commands XSR Getting Started Guide 3-37 bootFirst size=28992 sum=0xc 2e5 compressed_size=28992 entry=0x80020000 bootrom size=842656 sum=0xfa 65 compressed_size=347728 entry=0x81e00000 OK Proceed with erasing current Bootrom in flash and replace with btXSR3000_1_ 2.
Bootrom Monitor Mode Commands 3-38 Software Configuration df This command shows free disk space. Sample output is shown as follow s: XSR-3150:df Free space on flash: is 3383 296 bytes (0x33a000). del This command removes a file fr om flash: or cflash: memory .
Bootrom Monitor Mode Commands XSR Getting Started Guide 3-39 Set working directory to fla sh: Using default Bootrom passwo rd. The system is not secure!!! Use “bp” to change password ffc This command formats the CompactFlash card. ng This command retrieve s a file over the network using a remote IP addre ss/file path.
Bootrom Monitor Mode Commands 3-40 Software Configuration remove This command removes a file using the syntax remove <sour ce name> <destination name> rename This command renames a file using the syntax rename <source name> <destination name > sb This command displays boot values.
Bootrom Monitor Mode Commands XSR Getting Started Guide 3-41 ...... si This command displays XSR 30 00 Series inventory with this sample output: XSR-3150: si Hardware: Motherboard Information: XSR-315.
Bootrom Monitor Mode Commands 3-42 Software Configuration sv This command shows the bootr om version with sample output below: XSR-3150: sv X-Pedition Security Router B ootrom Copyright 2003 Enterasys Net works Inc. HW Version: 9002914-04 REV0A Serial Number: 3646031700233215 CPU: Broadcom BCM1250 Rev 2 VxWorks version: VxWorks5.
A-1 A Specifications System S pecifications This appendix details XSR data about har dware functionality including : • Process or , system memory , chassis, power supply , interfaces • Required ca.
Cable, CompactFlash and Accessory Specifications A-2 Cable, Comp actFlash and Accessory Specifications Refer to the following table for s pecifications of cables, CompactFlash and accessories for the XSR. This equipment can all be obtained separately fr om Enterasys Networks or thr ough any computer supply retailer .
Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-3 1000Base-SX Mini-GBI C with connector 1000Base-LX Mini-GBI C with connector 1000Base-SX Mini-GBI C with connector Short-h.
Cable, CompactFlash and Accessory Specifications A-4 COM (Console) Po rt The XSR comes equipped with a COM serial port useful for initial configuration and management. Using a serial ( null modem) cable, you can attach the route r ’s DB-9 COM port to a data terminal port and directly configur e the XSR over th e asynchr onous connection.
Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-5 GigabitEtherne t Port s The XSR comes equipped with three GigabitEthernet (LAN) ports that support full-duplex 10, 100, or 1000 Mbps transmission. The ports conform to IEEE 802.
Cable, CompactFlash and Accessory Specifications A-6 Copper/Fiber-optic Ethernet NIMs The single-port Copper or Fiber - optic Ethernet NIMs, shown in Figure A-3 and Figure A-4 , provide interfaces for half and full-d uplex 10/10 0Base-T or fiber-optic 100Base-F transmission over LAN or W AN networks, respectively .
Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-7 2/4-Port Serial NIM Card Port The High Speed Serial NIM car d, as shown in Figure A-6 , provides a W AN interface supporting a serial link to four differ ent types of DTEs: DB-15, 25 , 37, and V .
Cable, CompactFlash and Accessory Specifications A-8 Figure A-8 E IA-232/5 30 DTE Pin Assignments 17 18 19 27 21 3 16 2 RxD2 + RxD 2- TxD 2 + 1 2 3 11 5 10 4 7 6 8 12 13 15 16 9 14 6 22 3 16 2 14 4 19.
Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-9 Figure A-9 EIA-449 DTE Pin Assignment s 17 18 19 27 21 26 20 1 2 3 11 5 10 4 7 6 8 12 13 15 16 9 14 11 29 6 24 4 22 7 25 .
Cable, CompactFlash and Accessory Specifications A-10 Figure A-10 Combined V .35/EI A-232/530 DTE Pin Assignment s 1 2 3 11 5 10 4 7 6 8 12 13 15 16 9 14 3 16 2 14 4 19 5 13 15 12 17 9 7 20 23 1 RxD3+.
Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-11 Figure A-1 1 V .35 DTE Pin Assignment s 17 19 27 21 26 1 3 11 5 10 4 15 6 16 12 13 9 14 E R T P S C D Y AA V X B H A DSR.
Cable, CompactFlash and Accessory Specifications A-12 T1/E1/ISDN PRI NIM Card Port s The T1/E1/ISDN PRI NI M, as shown in Figure A-12 , comes equipped with either 1, 2 or 4 Ethernet (W AN) ports that .
Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-13 Balun for E1 or PRI NIM Cards Some overseas electrical systems r e quir e that yo u use a balun and grounding shunt when utilizi ng an E1 or PRI NIM card on the XSR.
Cable, CompactFlash and Accessory Specifications A-14 Grounding Shunt for E1 NIM Cards If you connect a balun to a 75-ohm line , you wi ll also need to attach a g r ounding shunt (or terminal strip) to any NIM pins whose RJ-48C con n ectors utilize the balun.
Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-15 T3/E3 NIM Card The T3/E3 full and sub-rate NIM, as shown in Figur e A-17 , is equipped with 1 Ethernet (W AN) port that supports fractional T3 /E3 transm ission in un-channelize d or clear channel mode with BNC connectors.
Cable, CompactFlash and Accessory Specifications A-16 1/2-Port BRI-S/T ISDB NIM Card Port s The XSR provides a serial NIM card for 1 or 2 W AN interfaces over an ISDN-S/T BRI line, as shown in Figur e A-18 . The Port 0 and 1 LEDs shin e when the lines ar e active and r eady to receive traffic.
Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-17 Inst alling Shunt/T erminal Strip T o install the shunt or terminal strip, attach two dual-pin units vertically to P1 and P2 four-pin jumpers corresponding to the RJ-45 port using a balun, as shown in Figure A-20 .
Cable, CompactFlash and Accessory Specifications A-18 1/2-Port BRI-U NIM Card Port s The XSR provides a serial NIM car d for 1 or 2 W A N interfaces over an ISDN BRI-U line, as shown in Figure A- 21 . Port 0 and 1 LEDs shine when the lines are active and ready to re ceive traffic.
Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-19 1-Port ADSL NIM Card Port The XSR’s Asymmetric Digital Subscriber Line (A DSL) NIM card, as shown in Figur e A-23 , provides 1 W AN port on an ADSL over POTS (A nnex A/C) or ISDN (Annex B) line with a 6-pin RJ-1 1 connector .
Cable, CompactFlash and Accessory Specifications A-20 T1/E1 Drop & Insert (D&I) NIM The XSR’s 2-port T1/E1 D& I NIM card, as shown in Figur e A-25 , is designed as an intermediary between the Central Of fice T1/E1 line and a PBX.
Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-21 Comp actFlash Memory Card The optional plug-in CompactFlash (CF) memory card, shown in Figure A-27 , comprises a single .
Cable, CompactFlash and Accessory Specifications A-22 VPN ON VPN tunnel is up OFF No VPN tunnel connected COM(munication) Blinking Port is transmitting or receiving data OFF Port is idle Ethernet Port.
Index-1 Index B Balun description A-13 Balun adapte r A-3 BRI S/T card part numbers A-3 BRI S/Tpin assignments A-16 BRI U card part numbers A-3 BRI-U pin assignme nts A-18 , A-19 , A-20 Broadcom 1250 .
Index-2 features 1- 1 GigabitEthernet port pi nouts A-5 hardware features 1-2 hardware specifications A-1 how to attach the Ethernet serial cable 2-10 how to attach the internal power supply cord 2-12.
An important point after buying a device Enterasys Networks XSR-3150 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Enterasys Networks XSR-3150 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Enterasys Networks XSR-3150 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Enterasys Networks XSR-3150 you will learn all the available features of the product, as well as information on its operation. The information that you get Enterasys Networks XSR-3150 will certainly help you make a decision on the purchase.
If you already are a holder of Enterasys Networks XSR-3150, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Enterasys Networks XSR-3150.
However, one of the most important roles played by the user manual is to help in solving problems with Enterasys Networks XSR-3150. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Enterasys Networks XSR-3150 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
