Instruction/ maintenance manual of the product CM Version 1.0 Enterasys Networks
Go to page of 38
Enterasys Matrix ™ X Router DC Power Supply P/N 9034200 Installation Guide.
.
i Notice Enterasys Networks reserv es the right to make changes in specifications and other information contained in th is document and its web site without prior notice.
ii Regulatory Compliance Information Federal Communications Commission (FCC) Notice This device com plies with Pa r t 15 of the FC C rules.
iii Electromagnetic Compatibility (EMC) This product complies with the following: 47 CF R Pa r t s 2 and 15, CSA C108.8, 2006/95/EC, EN 55022, EN 61000 ‐ 3 ‐ 2, EN 61000 ‐ 3 ‐ 3, EN 55024, AS/NZS CISPR 22, VCCI V ‐ 3.
iv ѻ ѻ ક䇈ᯢк䰘ӊ Supplement to Product Instructions ᳝↦᳝ᆇ⠽䋼ܗ㋴ (Hazardous Substance) 䚼ӊৡ⿄ (Parts) 䪙 3E ∲ +J 䬝 &G ݁Ӌ䫀 .
v VCCI Notice This is a class A product based on the standard of the Vo l u n t a r y Control Coun cil for Interference by Information Te c h n o l o g y Equipment (VCCI).
vi Declaration of Conformity Application of Co uncil Directiv e(s): 2004/108/EC 2006/95/EC Manufacturer ’ s Name: Enterasys Networks, Inc. Manufacturer ’ s Address: 50 Minuteman Road Andover , MA 01810 USA European Representativ e Address: Enterasys Networks, Ltd.
vii Enterasys Networks, Inc. Fi rmware License Agreement BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT. This document is an agreement (“ Agreement”) betwee n the end user (“Y ou”) and Enterasys Networks, In c.
viii 4. EXPORT RESTRICTIONS. You understand that Entera sys and its Affiliates are subject to regulation by agencies of the U.
ix 8. AUDIT RIGHTS. You here by acknow ledge that the intellectual property rights associated with the Prog ram are of critical value .
x.
xi Contents Chapter 1: DC Power Supply Installation Overview of the DC Power Supply .. ................ ................ ............. ................. ................ ............... .... .. 1-2 Power Supply Redundancy Planning .............. .....
xii.
Matrix X Router DC Power Supply Installation Guide xiii About This Guide This guide describes the Enterasys Matrix ™ X Router DC power supply features .
Conventions Used in This Guide xiv About This Guide Documentation can be accessed on the Wo r l d Wide We b , at the following URL: http://www .
Getting Help Matrix X Router DC Power Supply Installation Guide xv Getting Help For additional support related to the DC pow er supply or this document, .
Getting Help xvi About This Guide.
Matrix X Router DC Power Supply Installation Guide 1-1 1 DC Power Supply Installation This chapter provides installation instructions for the Enterasys Matrix™ X Router DC power supply module (X ‐ DC ).
Overview of the DC Power Supply 1-2 DC Power Supply Installation Overview of the DC Power Supply The DC power suppl y (X ‐ DC) can be used in the Enterasy s .
Overview of the DC Power Supply Matrix X Router DC Power Supply Installation Guide 1-3 Figure 1-2 Back V iew of the DC Power Supply The DC power suppl y provides the following .
Installation Site Requirements 1-4 DC Power Supply Installation Power Supply Redundancy Planning Because chassis syste m components consume va r yi n g amounts of elect.
Pre-Installation Tasks Matrix X Router DC Power Supply Installation Guide 1-5 Pre-Inst allation T asks Complete the followin g tasks before installing the DC power .
Pre-Installation Tasks 1-6 DC Power Supply Installation 2. Use the information from the output of the show system hardware command to fill out the worksheet in Ta b l e 1 ‐ 1 for each module as follows: a.
Pre-Installation Tasks Matrix X Router DC Power Supply Installation Guide 1-7 New DC Power Matrix X System Inst allations If the system is a new Matrix X DC ‐ pow ered installation, fol low this procedure to ve ri fy DC power compliance of all modules: 1.
Pre-Installation Tasks 1-8 DC Power Supply Installation Prep are Site Wiring fo r DC Power Inst allation 1. Ensure that a branch circuit disconnect device is installed,.
Unpacking the DC Power Supply Matrix X Router DC Power Supply Installation Guide 1-9 Unp acking the DC Power Supply To unpack the DC power supply: 1. Open the box and remov e the packing material protecting the DC power supply.
Installing the DC Power Supply 1-10 DC Power Supply Installation 3. Remove the tape seal on the non ‐ conductiv e bag to remov e the module.
Installing the DC Power Supply Matrix X Router DC Power Supply Installation Guide 1-11 2. Remove the vent plate covering all powe r supply slots by loosening the top and bottom captive screws, as shown in Figure 1 ‐ 3 .
Installing the DC Power Supply 1-12 DC Power Supply Installation 5. Hold the power supply by placing one ha nd on the handle located on the front panel and using you r other hand to support the power supply .
Installing the DC Power Supply Matrix X Router DC Power Supply Installation Guide 1-13 Figure 1-5 Removin g Blank Co verplate from Power Supply Slot 10. Connect the chassis to earth ground utilizing the earth ground connection on the back of the unit.
Removing a Power Supply 1-14 DC Power Supply Installation b. Place the lock wa s h e r s over the positive and negative studs. c. Place the nuts ov er the lock was h e r s and tighten.
Removing a Power Supply Matrix X Router DC Power Supply Installation Guide 1-15 Caution: If you want to operate the chassis with only one power supply , be sure to install the coverplate in place of the removed power supply to contain EMI radiation and ensure proper air circulation.
Removing a Power Supply 1-16 DC Power Supply Installation.
Matrix X Router DC Power Supply Installation Guide 2-1 2 DC Power Supply Specifications This chapter provides the DC power supply specifications and regulatory complianc e information. S pecifications Ta b l e 2 ‐ 1 lists the physical specifications.
Power Supply Redundancy 2-2 DC Power Supply Specifications Compression Lugs The DC power supply positive and negative bolt patterns match up to a 1/4 ‐ inch diame ter , 2 ‐ hole compression lug spaced 5/8 ‐ inch on center .
Power Supply Redundancy Matrix X Router DC Power Supply Installation Guide 2-3 T able 2-3 Modu le Power Spe cifications Module @ 48 VDC Power (W atts) Thermal Output (BTU/HR) CM 97 W atts 331.1 BTU/HR Fan tray 85 W atts 290.1 BTU/HR X4-FM 30 W atts 102.
Regulatory Compliance 2-4 DC Power Supply Specifications Regulatory Compliance The DC power suppl y meets the safety and electromagnetic compatibil ity (EMC) requirements listed in Ta b l e 2 ‐ 5 : T able 2-5 Complia nce St andards Regulatory Compliance Stan da r ds Safety UL 60950, CSA C22.
An important point after buying a device Enterasys Networks CM Version 1.0 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Enterasys Networks CM Version 1.0 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Enterasys Networks CM Version 1.0 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Enterasys Networks CM Version 1.0 you will learn all the available features of the product, as well as information on its operation. The information that you get Enterasys Networks CM Version 1.0 will certainly help you make a decision on the purchase.
If you already are a holder of Enterasys Networks CM Version 1.0, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Enterasys Networks CM Version 1.0.
However, one of the most important roles played by the user manual is to help in solving problems with Enterasys Networks CM Version 1.0. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Enterasys Networks CM Version 1.0 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
