Instruction/ maintenance manual of the product RSIB 300-500 Energy Tech Laboratories
Go to page of 16
3002503 11.06 Installation & Operating Manual USA CAN RSIB 300-500 Power V enter EXHAUSTO Inc. 1200 Northmeadow Pkwy . Suite 180 Roswell, GA 30076 P: 770.
2 3002503 11.06 Symbol Legend: The following terms are used throughout this manual to bring attention to the presence of potential hazards, or to important information concerning the product. Danger: Indicates an imminent hazardous situation which, if not avoided, will result in death, serious injury or substantial property damage.
3 3002503 11.06 1. Product Information 1.1 Function Use The EXHAUSTO RSIB Power V enter is intended for use as an in-line draft inducer/power venter . It can be installed in-line with the chimney or stack, and can be used in sidewall and vertical venting arrangements.
4 3002503 11.06 1.3 Shipping Standard packing list The RSIB contains the following: • The RSIB is shipped with two integrated sets of mounting brackets for use when hung from the ceiling. If other components are shipped, these will appear as separate items on the shipping packing list.
5 3002503 11.06 Prepared for ceiling mounting Cast-aluminum impeller Easy access to inside of fan Capacity: RSIB 40 0 0 1000 2000 5000 0.0 1.0 0.5 2.0 1.5 3.0 2.5 4.0 3.5 5.0 4.5 3000 4000 P t (inW .C.) V olume (cfm) 6000 RSIB 500 RS I B 35 0 RSIB 30 0 2.
6 3002503 11.06 3. Mechanical Installation 3.1 General W arning: Failure to install, maintain and/or operate the RSIB Power V enter in accordance with the manufacturer ’ s instructions may result in conditions which can produce bodily injury and property damage.
7 3002503 11.06 Sidewall V enting V ertical V enting Thegure below shows typical installation arrangements: 3.3 Mounting of Power V enter The power venter can be installed in a variety of positions. It can be suspendedfromaceilingorplacedonashelf/oor .
8 3002503 11.06 3.4 Connection to Chimney or V ent Follow the recommendations by the vent or stack manufacturer . For optimal performance, the distances in Fig. 6 should be observed. 3.5 Connection to Flexible Duct Flexible duct (FLF) is used to reduce the effects of pulsating appliances on the fan and duct system.
9 3002503 11.06 ! 4. Electrical Installation 4.1 General Danger: T urn off electrical power before servicing. Contact with live electric components can cause shock or death. Notice: If any of the original wire supplied with the system must be replaced, use similar wire of the same temperature rating.
10 3002503 11.06 4.3 Wiring Diagram – RSIB 350-500 PowerV enterandmotorspecicationscanbefoundunder“Sec.2.1DimensionsandCapacities”.Thepowerventer is equipped with a variable speed motor .
1 1 3002503 11.06 4.4 Installing a Proven Draft Switch A safety system must be interlocked with the appliance. The safety system could utilize a Proven Draft Switch (PDS-1),athermalswitch,aowswitchorasailswitch.
12 3002503 11.06 BLACK BLACK RED GREEN POWER SUPPL Y 200-240/3/60 or 440-480/3/60 WEATHERPROOF BOX VARIABLE FREQUENCY DRIVE (typical) FAN MOTOR L1 L2 L3 U V W SWAP THESE WIRES - ON THE OUTPUT SIDE! 4.
13 3002503 11.06 5.StartupandConguration 5.1 General The purpose of this fan is to ensure safe venting for a single appliance or multiple appliances. This can be performed via modulation, or through a single speed where modulation is not required.
14 3002503 11.06 6. Maintenance and T roubleshooting 6.1 General The power venter is designed for prolonged use, and no regular maintenance is required. It should be inspected periodically (at least once a year), and cleaned, if needed. This specifically applies in case it is being used with fuel oil.
15 3002503 11.06 Problem Possible Cause Solution The fan is not operating - No power to the fan - Check the power supply wires in the junction box by the fan.
EXHAUSTO Inc. 1200 Northmeadow Pkwy . Suite 180 Roswell, GA 30076 P: 770.587.3238 F: 770.587.4731 T : 800.255.2923 info@exhausto.com us.exhausto.com 3002503 11.06 EBC 12, EBC 14 EN60335-1, EN60335-2-80, DS/EN 292-1, DS/EN 292-2 98/37/EF/-EEC/-EWG/-CEE Langeskov , 01.
An important point after buying a device Energy Tech Laboratories RSIB 300-500 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Energy Tech Laboratories RSIB 300-500 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Energy Tech Laboratories RSIB 300-500 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Energy Tech Laboratories RSIB 300-500 you will learn all the available features of the product, as well as information on its operation. The information that you get Energy Tech Laboratories RSIB 300-500 will certainly help you make a decision on the purchase.
If you already are a holder of Energy Tech Laboratories RSIB 300-500, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Energy Tech Laboratories RSIB 300-500.
However, one of the most important roles played by the user manual is to help in solving problems with Energy Tech Laboratories RSIB 300-500. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Energy Tech Laboratories RSIB 300-500 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
