Instruction/ maintenance manual of the product 105E Energy Tech Laboratories
Go to page of 14
E N Intr oduction The 105E colour monitor displays sharp and brilliant images of text and graphics with a maximum resolution up to 1024x768 pixels. It is optimal for Windows, spread sheets, and any other application. This monitor automatically scans horizontal frequencies from 30KHz to 54KHz,and vertical frequencies from 50Hz to 120Hz.
E N Note: If you experienced your monitor display is changing from color to mono, it's possible that you are using a non-VESA-DDC-standard video card. Please consult with your local PCEC dealer for more information. E NERGY S TA R is a U . S . registered mark.
E N Safety precautions and maintenance ◆ Disconnect the monitor from the mains supply if the monitor is not to be used for an extended period of time. ◆ Do not attempt to remove the back cover , as you will be exposed to a shock hazard. The back cover should only be removed by qualified service personnel.
E N 4 Installation Important: Please refer to the user’ s manuals of y our computer and video adapter to make sure these equipments are properl y installed and configured before installing the monitor . Positioning / V entilation ◆ Avoid exposing the monitor to direct sunlight, stoves or any other heat sources.
E N Connection Intel Based platform: 386, 486, Pentium, or other compatibles: • Connect the monitor to the computer using the supplied interface cables. Important: Please make sure the A C power to your computer is “OFF” before connecting or disconnecting an y display peripheral.
E N Connection to the mains (Rear of the monitor) Connecting to the mains This monitor is set to operate at a mains supply of ; 100-240 volts AC .If the mains voltage in your home is not between this, consult your dealer. Connect one end of the mains cord to the mains socket at the rear of monitor, and the other end to the mains supply.
E N Front Control locations and functions 7 For an optimized adjustment of the picture following controls are available at the front. POWER. Press this knob, the green LED lights and the power is ON. Press this knob again, the green LED disappears and the power is OFF.
E N 8 H-Size : to adjust the horizontal amplitude of the image. H-Center : to adjust the horizontal position of the image. V-Size : to adjust the vertical amplitude of the image. V-Center : to adjust the vertical position of the image. Pincushion: to correct the barrel distortion of the image.
E N (A) User mode: (12 modes) The set will save the user's setting parameters automatically. Press + to recall factory preset mode. Adjustment The monitor is pre-set with 7 modes for optimal display size and centering as indicated in the following table: Resolution Horizontal Vertical Mode (dots x lines) Freq.
E N (B) Power Management Signalling Power Management Definition VESA DPMS POWER SAVING STATES MODE VIDEO H-SYNC V-SYNC POWER USED POWER SAVING(%) ON Active Yes Yes < 100 Watts 0 % Stand-by Blanked .
E N T echnical information (I) General: Picture tube : 15 inch (38.1 cm), 90 ° deflection, non- glare, black matrix,light transmission 57%, phosphor P22 medium short, dotted pitch 0.
E N (III) Pin assignment: (1) The 15-pin D-sub connector (male) of the signal cable (IBM systems): 1 Red video input 9 No pin 2 Green video input 10 Logic ground 3 Blue video input 11 Identification output 4 Identification output - connected to pin 10 - Connected to pin 10 12 Serial data line (SDA) 5 Ground 13 H.
E N English Introduction .... 1 Feature Highlights .... 1 Safety precautions and maintenance .... 3 Package .... 3 End of life disposal .... 3 Installation .... 4 Connection .... 5 Connection to the mains .... 6 Front Control locations and functions .
E N OTHER LANGUAGE VERSIONS FRENCH(FRANCAIS) .... 13 Appendix English Information for Users in the U.S. ........ A1 FCC Declaration ........ A2 WARRANTY .
An important point after buying a device Energy Tech Laboratories 105E (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Energy Tech Laboratories 105E yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Energy Tech Laboratories 105E - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Energy Tech Laboratories 105E you will learn all the available features of the product, as well as information on its operation. The information that you get Energy Tech Laboratories 105E will certainly help you make a decision on the purchase.
If you already are a holder of Energy Tech Laboratories 105E, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Energy Tech Laboratories 105E.
However, one of the most important roles played by the user manual is to help in solving problems with Energy Tech Laboratories 105E. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Energy Tech Laboratories 105E along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
