Instruction/ maintenance manual of the product HSBF10LP Enerco
Go to page of 24
Installation instructions and Owner’s Manual 1 UNVENTED LP-GAS FIRE D ROOM HEA TER Blue Flame Heaters Plaqu e Heate rs Mod el # Bur n Rate Mod el # Bur n Rate MH BF 10 LP /H SB F1 0L P/ TS BF 10 LP .
2 Installation instructions and Owner’s Manual 70575 Rev . E 04/07 This appliance may be installed in an aftermarket* permanently manufactured (mobile) home, where not prohibited by local codes.This appliance is only for use with the type of gas indicated on the rating plate.
Installation instructions and Owner’s Manual 3 Product Features Figure 1 SAFETY DEVICE This heater has a pilot with an Oxygen Depletion Sensor (ODS) safety shut off system. The ODS/pilot shuts off the heater if there is not enough fresh air . IGNITION SYSTEM PIEZO: BF10LP/ IR10LP – The heater is equipped with a piezo manual ignitor .
4 Installation instructions and Owner’s Manual 70575 Rev . E 04/07 installed in that space, and an unconfined space as a space whose volume is not less than 50 cubic feet per 1,000 Btu per hour (4.8 m 3 per kW) of the aggregate input rating of all appliances installed in that space.
Installation instructions and Owner’s Manual 5 Figure 3. V entilation from Out doors If necessary , provide extra fresh air by using ventilation grilles or ducts. Connect these items directly to the outdoors or sp aces open to the out doors. These include attics* and crawl spaces.
6 Installation instructions and Owner’s Manual 70575 Rev . E 04/07 Figure 4 F ASTENING HEA TER TO W ALL Mounting Bracket The mounting bracket in located on the back panel of heater (see figure 5). It has been taped there for shipping. Remove mounting bracket from back panel.
Installation instructions and Owner’s Manual 7 1. Drill holes at marked locations using 5/16” drill bit. For solid walls (concrete or masonry), drill at least 1” deep. 2. Fold wall anchor as shown in figure 8 below . Figure 8. 3. Insert wall anchor (wings first) into hole.
8 Installation instructions and Owner’s Manual 70575 Rev . E 04/07 W ARNING: This appliance requires a 3/8” NPT (National Pipe Thread) inlet connection to the pressure regulator . Use of floor mounting feet will require you to use a 3/8 NPT street elbow to make gas connection.
Installation instructions and Owner’s Manual 9 Pressure T esting Heater Gas Connections: 1. Make sure that the heater supply piping system is connected and has been leak tested as described above. 2. Make sure control knob of heater is in OFF position.
10 Installation instructions and Owner’s Manual 70575 Rev . E 04/07 C . Use only your hand to push in or turn the gas control knob. Never use tools. If knob will not push in or turn by hand, don’t try to repair it; call a qualified service technician or gas supplier .
Installation instructions and Owner’s Manual 11 TO TURN OFF GAS T O APPLIANCE SHUTTING OFF HEA TER: 1. Turn control knob clockwise to the OFF position. 2. Turn off all electrical power to the appliance if servicing is to be preformed. 3. Turn off equipment shutoff valve.
12 Installation instructions and Owner’s Manual 70575 Rev . E 04/07 8. When the pilot is lit, turn control knob counter- clockwise to heating level. The main burner should light. 9. T o select the desired heat level, turn the tem- perature setting knob counterclockwise to between 1 & 5.
Installation instructions and Owner’s Manual 13 Figure 24a Figure 24b CLEANING AND MAINTENANCE W ARNING: T urn off heater and let cool before servicing. CAUTION: Y ou must keep control areas, burner and circulation air passageways of heater clean. Inspect these areas of heater before use.
14 Installation instructions and Owner’s Manual 70575 Rev . E 04/07 TROUBLESHOOTING NOTE: All troubleshooting items are listed in order of operation and likely occurrence. W ARNING: Only a qualified service person should service and repair heater . CAUTION: Never use a wire needle, or similar object to clean ODS/pilot.
Installation instructions and Owner’s Manual 15 TROUBLESHOOTING W ARNING: If you smell gas: • Shut off gas supply • Do not try to light any appliance • Do not touch any electrical switch; do not use any phone in your building • Immediately call you gas supplier from a neighbor’s phone.
16 Installation instructions and Owner’s Manual 70575 Rev . E 04/07 SPECIFICA TIONS IR10 LP IR20LPT IR30LPT BTU (Available) 10,000 20,000 30,000 T ype of Gas LP-Gas Only LP-Gas Only LP-Gas Only Igni.
Installation instructions and Owner’s Manual 17 REPLACEMENT P ARTS Note: use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty . P ARTS UNDER W ARRANTY Contact authorized dealer from whom you purchased this product.
18 Installation instructions and Owner’s Manual 70575 Rev . E 04/07 Thermostat models 2 20-2 36 39 38 35 16 21 20-1 16-1 16-2 33-2 6 8 26 30 29 17 34 24 3-5 22-3 31-1 31-1 19 13 23 18 10 32 12 3-3 3.
Installation instructions and Owner’s Manual 19 IR20L P T BF20L P T IR30LPT BF 30LPT 1 70600 70600 70605 70605 Cabinet As sem bly 1 1-1 70601 70601 70 606 706 06 Cabinet, Pa nel , Top 1 1-2 70603 70.
20 Installation instructions and Owner’s Manual 70575 Rev . E 04/07 ** Not sold separately – Must purchase Assembly * Items not shown 29 70 683 70683 7 068 3 7068 3 Fan 1 30 70 684 70684 70684 706.
Installation instructions and Owner’s Manual 21 NON-Thermostat models 33-1 22-1 1-1 3-1 3-3 3-2 3-6 3-5 26 7 8 23 24 13 1-4 1-2 1-3 6 15 14 42 5 22-3 22-2 20-2 16-2 16-1 16 2 20-1 BF10LP 27-2 16-2 1.
22 Installation instructions and Owner’s Manual 70575 Rev . E 04/07 P ARTS LIST Non-Thermostat model IR10LP , BF10LP , IR10 LP , BF10LP This list contains replacement part s used in your heater . When ordering part s, follow the instructions listed under Replacement Parts on page 17 of this manual.
Installation instructions and Owner’s Manual 23 36 70336 -- - Bracket, Bottom, Plenum Assembly 1 38 70677 --- Burner Plaques, 10 2 40 70678 --- Plaque Gasket, 10 2 42 70337 70337 Control V alve Knob.
24 Installation instructions and Owner’s Manual 70575 Rev . E 04/07 W ARRANTY INFORMA TION Keep this warranty Model _______________________ Serial No. ____________________ Date Purchased _______________ Always specify model and serial numbers when communicating with the factory .
An important point after buying a device Enerco HSBF10LP (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Enerco HSBF10LP yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Enerco HSBF10LP - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Enerco HSBF10LP you will learn all the available features of the product, as well as information on its operation. The information that you get Enerco HSBF10LP will certainly help you make a decision on the purchase.
If you already are a holder of Enerco HSBF10LP, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Enerco HSBF10LP.
However, one of the most important roles played by the user manual is to help in solving problems with Enerco HSBF10LP. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Enerco HSBF10LP along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
