Instruction/ maintenance manual of the product CF180AP00 Emerson
Go to page of 16
Part No. F40BP73570001 Form No. BP7357-1 U.L. Model No.: CF180 READ AND SA VE THESE INSTRUCTIONS Net Weight: 30.9 Lbs. BRIDGETON ™ Ceiling Fan Owner's Manual Model Number s CF180AP00 Antique P .
W ARNING: T o avoid fire, shock, and serious personal injury , follow these instructions. Safety Instructions 1. Read your owner ’ s manual carefully and keep it for future reference.
3 T ools Needed for Assembly One Phillips head screwdriver One wire stripper Six wire connectors (supplied) Three 60-watt (max.) candelabra base bulbs Materials Wiring, outlet box and box connectors must be of type required by the local code.
Preset Memory Feature Y our remote control receiver is equipped with a preset memory feature. The receiv- er will remember the light intensity and fan speed when the light and fan are turned off from the wall switch. When the wall switch is turned back on, the lights and fan will resume operation as they were prior to the switch being turned off.
2. Slide the four switch levers on the code switch to your choice of ON (up) or down positions. Use a ball-point pen or small screwdriver and slide the levers firmly up or down. 3. In the receiver (Figure 1), slide the four switch levers to the same positions as set in the transmitter .
6 It is critical that the clevis pin in the motor coupling is properly installed and the setscrews securely tight- ened. Failure to verify that the pin and setscrews are properly installed (as shown in Figure 3) could result in the fan falling. ! W ARNING HAIRPIN CLIP DOWNROD CLEVIS PIN MOTOR COUPLIN G SETSCREW (2) Figure 3 3.
7 8. T urn the fan motor and housing assem- bly upside down in preparation for mounting the fan blade assemblies. Remove and discard the three shipping retainers securing the motor hub in the motor housing. NOTE: T ake care not to scratch the fan housing when installing the blade assemblies.
2. Carefully lift the fan and seat the hang- er ball/downrod assembly on the hang- er bracket that was just attached to the outlet box (Figure 1 1). Be sure the groove in the ball is lined up with the tab on the hanger bracket (Figure 10).
9 1. Position the supply wires to the left side of the outlet box (Figure 12); position the fan wires to the right side. Partially insert the remote control receiver (flat side up) until one end rests on the hanger ball as shown in Figure 12. NOTE: Make all wiring connections using wire connectors (supplied).
7. Screw three 60-watt (maximum) cande- labra base flame bulbs into the light fitter sockets (Figure 15). 8. Unscrew the six ring screws from the lower ring assembly (Figure 15). Position the lower glass in the lower ring assembly so that the six channels in the glass align with the six arms of the lower ring assembly .
button is held down. When the light is at the desired brightness, release the button. 5. T o turn the light on and off, press and release the button. The light will turn on at the light level previously set (see step 4). 6. If airflow is desired in the opposite direction, turn the fan off and wait for the blades to stop turning.
12 Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the possibility of an electrical shock. ! W ARNING The use of any other control not specifically approved for this fan could result in fire, shock and per- sonal injury .
13 T rouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not 1. Fuse or circuit breaker 1. Check main and branch start. blown. circuit fuses or circuit breakers. 2. Loose power line 2. Check line power connections connections to the fan, or to fan and wire.
14 Repair Parts 10 16 12 3 2 1 5 4 7 6 14 21 19 23 H I OFF LOW MED 24 11 15 13 9 17 20 25 8 22 18 U.L. Model No.: CF180 BP7357 CF180 BRIDGETON 9/19/07 11:21 AM Page 14.
Part Numbers Key Model No. Model No. N o . Description CF180AP00 CF180GES00 * Hanger Pack, Consisting of: 761655-34 761655-35 1 Hanger Bracket — — 2 Hanger Ball — — 3 Downrod — — * Parts B.
LIMITED WARRANTY What The War ranty Covers: This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials. Y ou must be the original purchaser or user of the product to be covered.
An important point after buying a device Emerson CF180AP00 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Emerson CF180AP00 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Emerson CF180AP00 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Emerson CF180AP00 you will learn all the available features of the product, as well as information on its operation. The information that you get Emerson CF180AP00 will certainly help you make a decision on the purchase.
If you already are a holder of Emerson CF180AP00, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Emerson CF180AP00.
However, one of the most important roles played by the user manual is to help in solving problems with Emerson CF180AP00. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Emerson CF180AP00 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
