Instruction/ maintenance manual of the product MidiVerb 3 Alesis
Go to page of 63
A L ES I S MidiVerb 3 Reference M a nu a l.
i TABLE OF CONTENTS INTRODUCTION ............................................................................................ 2 FEATURES ............................................................................................................. 2 HOW TO USE THIS MANUAL .
ii SECTION 3 INTERFACING MIDIVERB III ......................................................................... 14 INSTRUMENTS/MICROPHONES ........................................................................... 14 MONO OPERATION ..................
iii TRANSMITTING PROGRAMS VIA MIDI .................................................... 42 RECEIVING PROGRAMS VIA MIDI ........................................................... 43 MIDI MAPPING ........................................................
.
USERS MANUAL.
INTRODUCTION 2 Alesis MIDIVERB III 16 BIT MULTI-EFFECTS PROCESSOR WITH REAL-TIME MIDI PARAMETER CONTROL INTRODUCTION The A lesis MIDIVERB III is a high quality multi-effects unit which features up to 4 simultaneous effects (Delay, Reverb, Chorus, EQ) at a full 15KHz bandwidth and with 16 bit resolution.
INTRODUCTION 3.
INTRODUCTION 4 HOW TO USE THIS MANUAL Since a musician's time is better spent making music than reading manuals, we've tried to make this manual not only easy to use, but also fast and easy to find things when you need to.
QUICK START 5 SECTION 1 MIDIVERB III QUICK START FACTORY PROGRAMS The MIDIVERB III contains 200 factory supplied programs, 100 of which are stored in memory locations 000 to 099 and repeated again in locations 100 to 199. Only the programs in locations 100 to 199 can be permanently al tered and stored as desired by the user.
SECTION 1 6 2) Pressing the EDIT button again will select the upper LED which indicates that the top row of edit functions on the top row of buttons can be accessed. 3) Select the desired function to be edited. The stored value of the parameter will appear in the numeric dis play and the button will light up.
QUICK START 7.
SECTION 1 8 SAVING (STORING) EDITED PROGRAMS 1) Once a program has been edited to your liking, press the STORE button. The LED in the middle of the button will flash.
DESCRIPTION OF CONTROLS 9 SECTION 2 DESCRIPTION OF CONTROLS FRONT PANEL INPUT The INPUT control is a stereo control that determines the master volume level of the signal being fed into both inputs of the MIDIVERB III . MIX The MIX control determines the ratio of direct to effect signal.
SECTION 2 10 VALUE The VALUE buttons can be used to select the desired number or, once a desired parameter has been selected, edit the parameters value.
DESCRIPTION OF CONTROLS 11 DELAY/2 When in the EDIT mode, pressing the DELAY button will access either the D ELAY TIME or D ELAY REGENERATION amount for edit ing, depending which EDIT LED is lit. The D ELAY TIME parame ter allows the user to adjust the time between repeats as required.
SECTION 2 12 MIX/5 When in the EDIT mode, pressing the MIX button will adjust the relative level of either the Delay or Reverb, depending on which page the Edit LED is set. The Chorus level is always the same and is either On or Off depending upon the Configuration selected.
DESCRIPTION OF CONTROLS 13 When in the EDIT mode, the MIDI button is used to select the send and receive channel for the MIDIVERB III . The range is channel 01 through 16. Pressing the MIDI button a second time selects if the MIDIVERB III will accept MIDI Program Change commands.
SECTION 2 14 The other half of the MIDI program MAPPING section when in the EDIT mode, the INT. PROG (Internal Program) button selects the internal MIDIVERB III program (from 000 to 199) that will be cho sen by the external MIDI program number that is selected by the MIDI PROG button.
DESCRIPTION OF CONTROLS 15 Retransmits MIDI information received by MIDIVERB III to other MIDI units if the MIDI ECHO function is enabled. Also used as a MIDI OUT jack for MIDI system exclusive data dumps. BYPASS JACK The BYPASS jack bypasses the effects of the MIDIVERB III and supplies only Direct Signal Level to the stereo outputs.
SECTION 2 16 Program button Value buttons Edit button LED display Clip indicator Reverb button Delay button Chorus button EQ button Mix button Store button Signal present LED Input Mix Output Config button Mod button MIDI button MIDI Mapping buttons (Mapping and Int.
INTERFACING MIDIVERB III 17 SECTION 3 INTERFACING MIDIVERB III INSTRUMENTS MICROPHONES The A lesis MIDIVERB III has high impedance inputs that are ideally suited for use either with instruments or line level signals.
SECTION 3 18 MIXING CONSOLES INTERFACING VIA AUX SENDS The MIDIVERB III handles mono or stereo sends at all system levels. The input circuitry of the MIDIVERB III can easily handle +4dBv levels (+20dBv peaks), while having enough input or output gain to interface with the extremely low signal levels of budget recording systems.
INTERFACING MIDIVERB III 19 AUX SEND 1 RIGHT INPUT AUX RETURN OR INPUT CHANNEL LEFT OUPUT RIGHT OUPUT B. STEREO IN - STEREO OUT LEFT INPUT AUX SEND 2 INTERFACING VIA INSERT SEND AND RETURNS Another way of interfacing the MIDIVERB III is to connect the unit directly to the insert send and return patch points of the channel that is to be effected.
SECTION 3 20 CONNECTION TO THE MAIN OUTPUTS Still another way of interfacing the MIDIVERB III to a mixer or recording console would be in-line across the output of your mix ing console ( See Figure 4 ). This setup would be used only if you needed to effect the entire mix.
INTERFACING MIDIVERB III 21 2) Now turn the OUTPUT LEVEL control up (clockwise) un til there is sufficient level at the amplifier or mixer. Be careful not to turn the OUTPUT LEVEL control up too high since the strong signal may cause your amplifier or mixer to overload.
SECTION 4 22 SECTION 4 USING MIDIVERB III PROGRAM MODE When power is first turned on, the MIDIVERB III automatically re sets to the Program mode and the last program selected before the power was turned off will be currently selected. For the purpose of illustration, let's assume that you are turning your MIDIVERB III on for the first time.
USING M IDIVERB III 23 023 Note that the front panel still displays the following: — The PROGRAM LED will be lit, indicating that the MIDIVERB III is in the Program mode. — The display will read the program number, only now it reads "023".
SECTION 4 24 Pon 3) Press the "Up" VALUE button until display read "Pon" 4) Set program 023 on the MIDIVERB III to correspond with the desired program number on your synth, se quencer, or other MIDI device. (see " How to Use MIDI Mapping" on page xxxxxxx).
USING M IDIVERB III 25 ro1 3) Select the desired function to be edited. The stored value of the parameter will appear in the numeric dis play and the button will light up. In this case we will edit the DELAY TIME. When we se lect the DELAY button, the display will read: 080 4) Press either VALUE button to adjust the desired param eter.
SECTION 4 26 REVERB Reverb can be thought of as a great number of distinct echos, called reflections, that occur so fast that our ear hears them blurred together as one.
USING M IDIVERB III 27 REVERB DECAY The Reverb Decay determines the length of time that the Reverb will sound before it finally fades away. It is not used in the Reverse 1 and 2 Algorithms. It is functional in all others. DELAY The Delay section of the MIDIVERB III can be used in two modes, depending upon the configuration.
SECTION 4 28 There are 24 different Chorus Algorithms (Chorus versions), in the MIDIVERB III . Each algorithm has a different sound and simu lates a different pitch based effect. There are two major types of algorithms: Chorus and Flanging (see explanation below).
USING M IDIVERB III 29 variables are available, from varying the Speed and Depth of the LFO to feeding back part of the signal to make the effect stronger.
SECTION 4 30 INPUT EQ The INPUT EQ is a high-cut filter that rolls off the high frequency response of the input signal before it is sent to either the Delay, Reverb, or Chorus. The VALUE button selects the frequency where the signal has been rolled off -3dB.
USING M IDIVERB III 31 MODULATING MIDIVERB III 's PARAMETERS MOD PARAMETERS The MOD section lets you control various MIDIVERB III parame ters from a MIDI controller such as the pitchwheel, modwheel, keyboard aftertouch, keyboard note number, keyboard velocity, sustain pedal, or breath controller.
SECTION 4 32 FIGURE 8 MIDI CONTROLLER SOURCES CONTROLLER DESCRIPTION PITCH BEND The pitch bend wheel or lever common on most synthesiz ers. CONTROLLER #1 The Mod Wheel common on most synthesizers is desig nated Controller #1 in the MIDI specification.
USING M IDIVERB III 33 Figure 10 shows how MIDIVERB III will display the routing and which controller/parameter combinations are active. FIGURE 10 MIDIVERB III MOD ROUTING DISPLAY 1st character of dis.
SECTION 4 34 PdL Pitchwheel Delay Level 1dL Modwheel Delay Level ndL Note Number Delay Level UdL Velocity Delay Level AdL Aftertouch Delay Level SdL Sustain Pedal Delay Level bdL Breath Controller Del.
USING M IDIVERB III 35 PLEASE NOTE : In all Configurations except #14 and 15, the maximum delay is 100 milliseconds. In Configurations #14 and 15, the maximum delay time is 490 milliseconds .
SECTION 4 36 FIGURE 10 CONFIG CONFIGURATION CHRS in REVERB NUMBER SIGNAL PATHS OUTPUT PRE-DELAY 1 EQ > CHRS > DELAY > REVERB ON YES 2 EQ > CHRS > REVERB ON NO EQ > CHRS > DELAY 3 .
USING M IDIVERB III 37 Below is a chart for each configuration that shows what the effects possibilities of each are, as well as where the Chorus section is routed to.
SECTION 4 38 CONFIGURATION 1 CHORUS EFFECTS POSSIBILITIES Routed to Output 1. EQ'd, Chorused, Predelayed Reverb 2. EQ'd, Chorused, Predelayed Reverb with echo 3.
USING M IDIVERB III 39 CONFIGURATION 3 CHORUS EFFECTS POSSIBILITIES Routed to Output 1. EQ'd Chorused Reverb 2. Delay 3. All of the above at once 4.
SECTION 4 40 CONFIGURATION 5 CHORUS EFFECTS POSSIBILITIES Routed to Output 1. EQ'd Reverb 2. Chorused Delay 3. All of the above at once 4. Chorus only EQ CHORUS DELAY REVERB DELAY LEVEL REVERB LE.
USING M IDIVERB III 41 CONFIGURATION 7 CHORUS EFFECTS POSSIBILITIES Routed to Effects only 1. EQ'd, Chorused, Predelayed Reverb 2. EQ'd, Chorused, Predelayed Reverb with echo 3.
SECTION 4 42 CONFIGURATION 9 CHORUS EFFECTS POSSIBILITIES Routed to Effects only 1. EQ'd Chorused Reverb 2. Delay 3. All of the above at once EQ CHORUS DELAY REVERB DELAY LEVEL REVERB LEVEL MIX L.
USING M IDIVERB III 43 CONFIGURATION 11 CHORUS EFFECTS POSSIBILITIES Routed to Effects only 1. EQ'd Reverb 2. Chorused Delay 3. All of the above at once EQ CHORUS DELAY REVERB DELAY LEVEL REVERB .
SECTION 4 44 EQ CHORUS DELAY REVERB DELAY LEVEL REVERB LEVEL MIX L R OUTPUT INPUT INPUT EQ TIME REGEN EQ 100ms ALGORITHM SPEED DECAY ALGORITHM CONFIGURATION 14 CHORUS EFFECTS POSSIBILITIES Routed to Output 1. EQ'd Chorus 2. EQ'd Chorused Delay 3.
USING M IDIVERB III 45 SAVING (STORING) EDITED PROGRAMS 1) Once a program has been edited to your liking, press the STORE button. The LED in the middle of the button will flash.
SECTION 4 46 USING MIDIVERB III WITH MIDI MIDI PARAMETERS The MIDI button accesses the various MIDI parameters of MIDIVERB III . The MIDI functions are global functions and are not stored with an individual program. MIDI CHANNEL The MIDIVERB III can receive MIDI information on channels 1 through 16.
USING M IDIVERB III 47 MIDI PROGRAM CHANGE Pressing the MIDI button a second time accesses the MIDI Pro gram Change page which allows the MIDIVERB III to change programs remotely by a MIDI Program Change command. The MIDIVERB III will also send Program Change commands when programs are selected from the front panel.
SECTION 4 48 exception of System Exclusive data) to be retransmitted back out the MIDI OUT jack..
USING M IDIVERB III 49 SELECTING MIDI ECHO 1) While still in the EDIT mode ( either EDIT LED lit), press the MIDI button THREE times . The numeric display will read "Eon" if MIDI Echo is on, and "Eof" if MIDI Echo is off.
SECTION 4 50 2) Press the STORE button, which causes MIDIVERB III 's entire memory to be sent out via MIDI to an external storage device like an A lesis DATADISK or another MIDIVERB III. The display will read "____" while sending the data, which will take about 1 second, after which it will return to "Snd".
USING M IDIVERB III 51 MIDI Controller Program 102 = MIDIVERB III Program 39 MIDI Controller Program 103 = MIDIVERB III Program 25 Selecting program 101 on the MIDI controller would result in pro gram.
SECTION 4 52 100 3) Select the INT. PROGRAM button on the MIDIVERB III . 4) Press the VALUE button until the desired internal MIDIVERB III program number is displayed. In this case it would be program 33. 033 5) Select the MIDI PROGRAM button on the MIDIVERB III once again.
USING M IDIVERB III 53.
SECTION 4 54 MISCELLANEOUS FUNCTIONS INITIALIZING THE MIDIVERB III There are two reasons why you may want to reinitialize your MIDIVERB III : 1) To return all programs to their factory parameter settings (called "initializing"). 2) In case the unit locks up from a power surge.
USING M IDIVERB III 55 DETERMINING THE CURRENT SOFTWARE VERSION 1) Hold the PROGRAM button and press the EDIT button. The display will read X.XX which represents the current version number of the software.
SECTION 5 56 SECTION 5 SPECIFICATIONS ELECTRICAL CHARACTERISTICS FREQUENCY RESPONSE 16Hz - 15KHz, ±1dB DYNAMIC RANGE 85 dB HARMONIC DISTORTION .1% typical @ 1KHz @ 0dBV INPUT NUMBER OF CHANNELS 2 NOM.
SPECIFICATIONS 57.
SECTION 5 58 MIDI CONTROL Program Change MIDI Sysex TransferMIDI Program Mapping MIDI Echo MIDI Modulation Exten sive real-time control of Program parameters and Effects levels Mod Sources Pitch bend,.
An important point after buying a device Alesis MidiVerb 3 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Alesis MidiVerb 3 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Alesis MidiVerb 3 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Alesis MidiVerb 3 you will learn all the available features of the product, as well as information on its operation. The information that you get Alesis MidiVerb 3 will certainly help you make a decision on the purchase.
If you already are a holder of Alesis MidiVerb 3, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Alesis MidiVerb 3.
However, one of the most important roles played by the user manual is to help in solving problems with Alesis MidiVerb 3. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Alesis MidiVerb 3 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
