Instruction/ maintenance manual of the product 20002514 Emerson
Go to page of 14
Installation Manual 20002514, Rev BA December 2010 Micro Motion ® R-Series Coriolis Flow Sensors.
Safety and approval information This Micro Motion product complies with all applicable European directives when properly installed in accordance with the instructions in this manual. Refer to the EC declaration of conformity for directives that apply to this product.
Contents Chapter 1 Planning ...........................................................................................................................1 1.1 Installation checklist .......................................................................
Contents ii Micro Motion R-Series.
1 Planning Topics covered in this chapter: • Installation checklist • Best practices • Environmental limits 1.1 Installation checklist □ Make sure that the hazardous area specified on the sensor approval tag is suitable for the environment in which the sensor is installed.
Recommended sensor orientation Table 1-3: Liquids Gases Slurries □ Install the sensor so that the flow direction arrow on the sensor matches the actual forward flow of the process. 1.2 Best practices The following information can help you get the most from your sensor.
Environmental limits for R-Series sensors Figure 1-1: Maximum process temperature in °F (°C) 176 (80) 140 (60) 104 (40) 68 (20) 32 (0) –4 (–20) –40 (–40) –148 (–100) 158 (70) Ambient tem.
2 Mounting 2.1 Mount the sensor Use your common practices to minimize torque and bending load on process connections. Tip To reduce the risk of condensation or excessive moisture, the conduit opening should not point upward (if possible). The conduit opening of the core processor can be rotated freely to facilitate wiring.
3 Wiring Topics covered in this chapter: • Options for wiring • Connect 4-wire cable 3.1 Options for wiring The wiring procedure you follow depends on which electronics option you have. See Table 3-1 for the wiring options for each sensor electronics option.
Step 1: Cable preparation Cable layout Run conduit to sensor Metal conduit Wrap the drain wires twice around the shield and cut off the excess drain wires.
Step 2: Shield termination Assemble the Gland 1. Fold the shield or braid back over the clamping insert and 1/8 inch (3 mm) past the O-ring. 2. Install the gland body into the conduit opening on the core processor housing. 3. Insert the wires through gland body and tighten the gland nut onto the gland body.
Step 3: Terminal connections Connect the wires to the transmitter terminals (see the transmitter manual) Reinstall and tighten the core processor cover From Step 1 or 2 Connect the wires to the core p.
4 Grounding The sensor must be grounded according to the standards that are applicable at the site. The customer is responsible for knowing and complying with all applicable standards.
*20002514* 20002514 Rev BA 2010 Micro Motion Inc. USA Worldwide Headquarters 7070 Winchester Circle Boulder, Colorado 80301 T +1 303-527-5200 T +1 800-522-6277 F +1 303-530-8459 www.micromotion.com Micro Motion Europe Emerson Process Management Neonstraat 1 6718 WX Ede The Netherlands T +31 (0) 318 495 555 F +31 (0) 318 495 556 www.
An important point after buying a device Emerson 20002514 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Emerson 20002514 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Emerson 20002514 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Emerson 20002514 you will learn all the available features of the product, as well as information on its operation. The information that you get Emerson 20002514 will certainly help you make a decision on the purchase.
If you already are a holder of Emerson 20002514, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Emerson 20002514.
However, one of the most important roles played by the user manual is to help in solving problems with Emerson 20002514. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Emerson 20002514 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
