Instruction/ maintenance manual of the product 330107 Aleratec
Go to page of 45
USER GUIDE Aleratec 1:1 1 USB Copy Cruiser SA™ Part No. 330107.
www .aleratec.com Copyright/Model Identification The content of this manual is for informational purposes only and is subject to change without notice.
www .aleratec.com Radio/TV Interference Statement The equipment described in this guide emits radio frequency energy . If it is not installed in accordance with the manufacturer ’ s instructions, it may cause interference with radio or television reception.
www .aleratec.com Safety Regulations W ARNING T o prevent re or shock hazard, do not expose the unit to rain or moisture. T o avoid electrical shock, do not open the cabinet.
www .aleratec.com T able of Contents Introduction .......................................................................................1 Product Features ..................................................................................... 1 Key Items – 1:1 1 USB Copy Cruiser SA .
www .aleratec.com.
www .aleratec.com 1 Introduction Thank you for purchasing this 1:1 1 USB Copy Cruiser SA. Please read this User Guide thoroughly before using this product. • Page 2 shows the 1:1 1 USB Copy Cruiser SA Display Panel. Product Features • Stand Alone, no computer required.
www .aleratec.com 2 Introduction 1:1 1 USB Copy Cruiser SA Display Panel 1 Display shows all functions and messages 2 ENT button is used to execute a selected function 3 ESC button is used to cancel a.
www .aleratec.com 3 Precautions Bef ore in stall ing your 1: 1 1 US B Cop y C rui ser S A, ple ase r ead th e f ollow ing . Installation A void placing the 1:11 USB Copy Cruiser SA in a location subje.
www .aleratec.com 4 Overview Main Menu This section provides a listing of the functions of the 1:1 1 USB Copy Cruiser SA. Detailed descriptions of each function are given in the next section. The functions are numbered for easy reference; these numbers are also used in the next section.
www .aleratec.com 5 Overview Subfunctions of Main Menu Items 5, 6, and 7 The main menu “Information” function has 2 subfunctions. These are: The main menu “Utility” function has 6 subfunctions. These are: 5.1 USB Info 5.2 System Info USB Duplicator 5.
www .aleratec.com 6 Overview Subfunctions of Main Menu Items 5, 6, and 7 - continued The main menu “Setup” function has 8 subfunctions. These are: 7.1 Start-up Menu 7.2 Copy Area USB Duplicator 7. Setup OK ESC 7.3 Button Beep 7.4 Asyn Hold Time 7.
www .aleratec.com 7 Using the USB Duplicator Synchronous and Asynchronous The 1:1 1 USB Copy Cruiser SA supports two copying methods: • Synchronous • Asynchronous Synchronous Copying Synchronous Copying means that all ash drives begin copying together .
www .aleratec.com 8 Using the USB Duplicator Main Menu Functions are selected with the arrow keys. The numbers correspond to the Function listing in the previous section. Copy This function makes USB ash copies. The duplicator auto detects and supports Synchronous, and Asynchronous methods of Copy .
www .aleratec.com 9 Using the USB Duplicator Synchronous Copying - continued 4. Finish loading the blank target ash drives, then press the OK button on the display panel.
www .aleratec.com 10 Using the USB Duplicator 2. Press the OK button on the display panel. The USB Duplicator will start to read the source content into the system’ s buffer and immediately start copying any loaded target USB ash drives. 3. Load the blank tar get ash drives into the USB Duplicator .
www .aleratec.com 1 1 Using the USB Duplicator Main Menu Compare This function will compare the nished target USB ash drives to the source USB ash drive after copying is complete. The USB Duplicator supports Compare in both Synchronous, and Asynchronous modes.
www .aleratec.com 12 Using the USB Duplicator 4. When Compare is complete the display will show the total, and the number that pass and fail. Asynchronous Compar e Asynchronous Compare is used only when the source content is the same as or less than the system buffer (256MB).
www .aleratec.com 13 Using the USB Duplicator Asynchronous Compar e - continued 4. As nished drives are removed, and new ash drives inserted, the display will show the number of comparisons completed and the number of USB ash drives still in the comparison process.
www .aleratec.com 14 Using the USB Duplicator Main Menu Copy+Compare This function will Copy and Compare USB ash drives. The duplicator auto detects and supports Synchronous, and Asynchronous methods of Copy+Compare. Synchronous Copy+Compar e In Synchronous Copy+Compare all USB ash drives are copied and compared simultaneously .
www .aleratec.com 15 Using the USB Duplicator Synchronous Copy+Compar e - continued 4. Finish loading the blank tar get ash drives, then press the OK button on the display panel.
www .aleratec.com 16 Main Menu Asynchronous Copy+Compar e Asynchronous Copy+Compare is used only when the source content is the same as or less than the system buffer (256MB).
www .aleratec.com 17 Using the USB Duplicator Asynchronous Copy+Compar e - continued 4. If the Copy fails, the LCD will display the number of ash drives that failed and passed. Note: During Asynchronous Copying you can use the UP and DOWN arrow keys to check each flash drives copying status.
www .aleratec.com 18 Using the USB Duplicator Main Menu Capacity Check This function will check the capacity of each ash drive inserted. When nished the following screen will appear . Using the UP and DOWN arrows, you can scroll thru each drive loaded to display capacity .
www .aleratec.com 19 Using the USB Duplicator 5.1 USB Info. USB Info is a function that displays the USB ash drives basic information such as ash type, content size, and available space. 1. Use UP or DOWN arrow to scroll through the menu until Information is displayed on the LCD screen.
www .aleratec.com 20 Using the USB Duplicator Main Menu Utility The main menu Utility function has 6 subfunctions. These are: 6.1 Format F A T 6.2 Measure Speed USB Duplicator 6. Utility OK ESC 6.3 Media Check 6.4 Quick Erase USB 6.5 Full Erase USB 6.
www .aleratec.com 21 Using the USB Duplicator Main Menu 6.1 Format F A T This function is used to format ash drives with the duplicator . If the original format is F A T , then the format operation will not change the format, but will write over any data on the ash drive.
www .aleratec.com 22 Using the USB Duplicator 6.2 Measure Speed This function will measure the read and write speeds of drives loaded in the ports. 1. Load drives. Use UP or DOWN arrow to scroll through the menu until Utility is displayed on the LCD screen.
www .aleratec.com 23 Using the USB Duplicator 2. Press OK and scroll to Media Check. The LCD will display the following status: 3. Use UP or DOWN arrow to scroll through the available options: 6.3.1 Safe Check This function will read all the data on the ash drive with no writing so as to preserve all of the data and format on the drive.
www .aleratec.com 24 Using the USB Duplicator 6.4 Quick Erase USB Quick Erase USB is a function that can quickly erase the target USB ash drive. Note: The Quick Erase USB function will only erase the F A T table index of each target flash drives. 1.
www .aleratec.com 25 Using the USB Duplicator 6.5 Full Erase USB Full Erase USB is a function what will erase all data on the target USB ash drive. Note: The Full Erase USB will completely erase data of each of the target flash drives This function will also clear the F A T table in the flash drive.
www .aleratec.com 26 Using the USB Duplicator 6.7 Calc. Checksum The Calculate Checksum function computes a checksum for the contents of the source drive. This alphanumeric can be used to ensure that no minor changes due to alteration or virus have occurred on the source drive since its last use.
www .aleratec.com 27 Using the USB Duplicator Main Menu Setup This function includes 8 subfunctions. These are: 7.1 Start-up Menu 7.2 Copy Area USB Duplicator 7. Setup OK ESC 7.3 Button Beep 7.4 Asyn Hold Time 7.5 Ignore Size 7.6 Asynchronous Enable/Disable 7.
www .aleratec.com 28 Using the USB Duplicator 7.1 Startup Menu Startup Menu allows you to select which function displays rst when the USB Duplicator is turned on. This function selects the menu item that will be the rst item shown on the display when you turn on the duplicator .
www .aleratec.com 29 Using the USB Duplicator 7.3 Button Beep This setting controls the button sound. 1. Use the UP or DOWN arrow to scroll through the menu until Setup is displayed on the LCD screen. Press the OK . 2. Use the UP or Down arrow to scroll through the Setup options until Button Beep is displayed on the LCD screen.
www .aleratec.com 30 Using the USB Duplicator 7.4 Asyn Hold T ime This function allows you to set the time to exit Asynchronous Copying when you pull all the USB ash drives out of the duplicator .
www .aleratec.com 31 Using the USB Duplicator 7.5 Ignore Size - continued 1. Use the UP or DOWN arrow to scroll through the menu until Setup is displayed on the LCD screen. Press the OK button to select or press ESC to go to the next setting. 2. Use the UP or Down arrow to scroll through the options until Ignore Size is displayed on the LCD screen.
www .aleratec.com 32 Using the USB Duplicator 7.6 Asynchronous (Enable/Disable) This function allows the user to enable/disable asynchronous copying. Use Up and Down arrow keys to toggle between and push OK to select, or ESC to exit.
www .aleratec.com 33 Specifications Operating T ype • Stand-alone (No PC Required) Number of T argets • 11 Supported Media • USB Flash/Pen Drive requiring less than 500mA from USB Port T ransfe.
www .aleratec.com 34 T echnical Support After reading this User Guide, if you need additional assistance with this product, please contact Aleratec T echnical Support. Our technical staff will be happy to assist you, but they may need your help to better assist you.
www .aleratec.com 35 Service and Support Aleratec, Inc., Limited W arranty This Limited W arranty covers defects encountered in the course of normal use of this product and does not apply to damage from improper use, abuse, accidents, unauthorized service, or inadequate packaging when shipping the product to Aleratec, Inc.
www .aleratec.com 36 Service and Support Please Note: This W arranty is valid only within the United States and Puerto Rico, and applies only to products that are new and unopened on the date of purchase.
www .aleratec.com 37 Service and Support T o Obtain W arranty Service: Y ou must ship your subsystem to the authorized dealer where your subsystem was purchased within the one year warranty period and no later than thirty days after discovery of claimed defect, whichever occurs rst.
www .aleratec.com 38 T echnical Support F AX Back Form Aleratec, Inc. T echnical Support Fax Back Form Please record the following information to help expedite any warranty claim: Model No.
Document Number: 330107_ENG_Rev . A Copyright © 2010 Specifications subject to change without notice. Aleratec, Inc. 9851 Owensmouth Avenue Chatsworth, CA 91311 U.
An important point after buying a device Aleratec 330107 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Aleratec 330107 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Aleratec 330107 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Aleratec 330107 you will learn all the available features of the product, as well as information on its operation. The information that you get Aleratec 330107 will certainly help you make a decision on the purchase.
If you already are a holder of Aleratec 330107, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Aleratec 330107.
However, one of the most important roles played by the user manual is to help in solving problems with Aleratec 330107. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Aleratec 330107 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
