Instruction/ maintenance manual of the product VR500CS-BT Elite
Go to page of 24
VR500CS-BT AM/FM Stereo In-Dash CD Player with USB Port, SD/MMC Card Slot, RDS , Remote Control, Aux In, and Recording Function.
2 W elcome! Dear Customer , CONGRA TULA TIONS. The VR500CS-BT MP3/CD Player with AM/FM Receiver , USB Port and SD Card Slot, Electr onic Anti-Shock (ESP) & Fold-down Detachable Face, when used as described, will give you years of dependable service in your car , truck, RV , or mini-van.
3 Precautions • Handle the disc by its edge to keep the disc clean. Do not touch the disc’ s surface. • Do not use a CD with paste or ink residue on it. • Do not use CDs with labels or stickers attached. The label may leave a sticky residue when it begins to peel.
4 • Disconnect negative battery terminal before starting installation. Consult the vehi- cle’ s owner’ s manual for proper instruction. • The unit is designed for a 12V olt DC negative ground operation system only . Before installing the unit, confirm that your vehicle is a 12V olt DC negative ground system.
5 Before Y ou Install Automotive audio equipment installations can be challenging at times, even to the most experienced of installation technicians. If you are not confident working with electrical w.
6 Installation DIN FRONT -MOUNT (METHOD A) Remove the half sleeve A E Remove the two transport screws fr om the top of the unit before installing. NOTE: Unit should be installed horizontally or less than a 30° angle. 1. Insert Half Sleeve into dash-board hole and bend mount tabs outwar ds to secure it.
7 DIN REAR-MOUNT (METHOD B) Installation using the screw holes on both sides of the unit. 1. Screw holes on the side of the unit. 2. Screws. Use either truss scr ews (5 x 8mm) or flush surface screws (4 x 8mm), depending on the shape of the screw holes in the bracket.
8 Installation BUIL T -IN MICROPHONE The built-in microphone is located on the fr ont left side of the unit. There is no setup re- quired for this micr ophone and it is tuned to pick-up the voices of the front and rear seat passengers. Built-In Microphone GIVE US A CALL, WE'LL HELP YOU INST ALL.
9 Wiring Connections Make sure you have good chassis gr ound. A good ground connection will eliminate most electrical noise problems. A good chassis gr ound requires a tight connection to the vehicle’ s metal chassis.
10 Location Of The Controls 12 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 1. / SEND 2. VOLUME UP 3. MICROPHONE 4. LCD SCREEN 5. No. 4 / RANDOM 6. No. 1 / P AUSE 7. No. 5 / -10 TRACK DOWN 8. No. 2 / REPEA T 9. No. 3 / INTRO 10.
11 Remote Control 1. T -MENU 2. / MODE/SEND 3. /CANCEL/MUTE 4. NO. 2 / REPEA T 5. NO.1 / P AUSE 6. NO. 5 / DOWN 10 7. NO. 4 / RANDOM 8. NO. 8/ T A CONTROL 9. NO. 7/ MONO 10. NO. 0/ DISC / RECORD 11. * SYMBOL / AS/PS 12. POWER 13. PREVIOUS/F AST REVERSE 14.
12 Basic Operation 1. TURNING THE UNIT ON / OFF Press any Button to turn the unit ON. On the Faceplate, press and hold the POWER button for 2 seconds to turn the unit off. On the Remote Control pr ess the Power button to turn the unit ON & OFF . 2.
13 Funct ion Men u(cont.) Te l v o l In order to maintain the sound quality of phone calls, TEL VOL is suggested to be be- low 35. T elephone default volume is 25. DSP Enables Pre-set Equlizer settings. Press V olume +/- buttons to choose a pre- set EQ.
14 Radio Operation CHOOSE RADIO BAND On the faceplate or remote contr ol, press the # / Band Button to change the radio band. The unit has five bands - three FM (FM1, FM2, and FM3) and two AM (AM1 and AM2) Band selects. Each of the five bands can store up to six pr eset stations, for a total of 30 preset memory stations.
15 Radio Operation T A (TRA VEL ANNOUNCEMENT) / TP (TRA VEL PROGRAM IDENTIFICA- TION) Enable or disable T A mode: (Default is OFF) 1) Press T A button once to activate the T raf- fic Announcement function, Press the T A button again to turn off the T A function.
16 Bluetooth Operation BLUETOOTH FEA TURES 1. Bluetooth V2.0 EDR compliant 2. Supports HFP , A2DP , A VRCP . 3. Class 2, Up to 8 meters wireless digital connection. 4. ECHO cancellation with noise elimination 5. Last number redial 6. Display incoming number 7.
17 CD Operation DISC SLOT Press the OPEN button to open the face- plate, then insert a disc into the disc slot. As the disc is read TOC READ will appear on the LCD, then the first track will start to play . • If there is err or , “CD ERROR” will be dis- played on LCD.
18 CD Operation (Cont) to resume playback. REPEA T On the Remote or Face Plate, press the No. 2/RPT Button to repeat the same track continuously . “RPT” will appear on the display . Press this button again to stop repeating tracks RANDOM On the Remote or Face Plate, press the No.
19 File Management FILE / FOLDER SEARCH In CD, USB, SD/MMC mode, press the * / AS/PS button to enter search mode. Below is toggle sequence of search modes.
20 COPYING A MP3 FILE FROM A CD When copying files from a MP3 CD you may only copy one file at a time. 1. Insert a CD with MP3 audio files into the disc slot. 2. Use the |<< button or the >>| button to start playing the file you wish to copy .
21 1. RCA OUTPUT The RCA Output Jacks are on the back of the unit. (Refer to Wiring Diagram) This out- put is for connecting an amplifier , equalizer , or other audio componement that requir es a pre-amp out connection. (Red = Right, White = Left) Follow the manufacturers in- structions for the audio component that you are connecting.
22 Specifications GIVE US A CALL, WE'LL HELP YOU INST ALL. 1-800-445-1797 PLEASE DO NOT RETURN PRODUCT TO STORE. Visit us on the WEB www .vr -3.com For Information and T echnical Assistance, Call T oll-Free in U.S.A. and Canada. GENERAL Power Supply .
VIRTUAL REALITY SOUND LABS ® pr oducts are designed and manufactured to pr ovide a high level of trouble-fr ee performance. VIRTUAL REALITY SOUND LABS ® warrants, to the original purchaser , that its products ar e free from defects in material and workmanship for 30 days fr om the date of original purchase.
©2008 Intellectual Solutions Inc., All Rights Reserved, All designs, logos and images are the exclusive pr operty of Intellectual Solutions Inc. and/or its affiliates.
An important point after buying a device Elite VR500CS-BT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Elite VR500CS-BT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Elite VR500CS-BT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Elite VR500CS-BT you will learn all the available features of the product, as well as information on its operation. The information that you get Elite VR500CS-BT will certainly help you make a decision on the purchase.
If you already are a holder of Elite VR500CS-BT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Elite VR500CS-BT.
However, one of the most important roles played by the user manual is to help in solving problems with Elite VR500CS-BT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Elite VR500CS-BT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
