Instruction/ maintenance manual of the product BAS 316G WNB Elektra Beckum
Go to page of 16
115 166 9103 / 4802 - 1.1 BAS 316G DNB / BAS 316G WNB Betriebsanleitung . . . . . . . . . . . . . . . . . . . . . 3 Operating Instruction . . . . . . . . . . . . . . . . . 15 Instructions d'utilisation . . . . . . . . . . . . . . . 27 Manuale d’istruzioni .
2 D DEUTSCH ENG ENGLISH KONFORMITÄTSERKLÄRUNG DECLARATION OF CONFORMITY Wir erklären in alleiniger Verantwortlichkeit, dass dieses Produkt mit den folgenden Normen übereinstimmt* gemäß den Besti.
15 ENGLISH 1. Parts identification (standard delivery) 2 5 6 7 8 9 11 12 13 1 14 15 16 17 18 19 10 3 4 Front 1 Upper housing door 2 Setting knob for band saw blade tension 3 Upper band saw wheel 4 Set.
16 ENGLISH 1. Parts identifi cation (standard delivery) .............. ......15 2. Please read first! ........... ............16 3. Safety ............... ................. .........16 3.1 Specified conditions of use .........16 3.2 General safety information .
17 ENGLISH Prevent body contact with earthed objects such as radiato rs, pipes, cooking stove s, refrigerat ors when operating this tool. • Do not use the powe r cable for any purpose it is not intended for. A Risk of injury by moving parts! • Do not operate th e tool without installed guards.
18 ENGLISH Both housing doors must be closed while the machine is in use. Electronic motor brake The wear-free electronic moto r brake (inside the saw, not illustrated) causes the band saw blade to stop within 10 seconds after the saw is turned OFF.
19 ENGLISH Rip fence The rip fence (33) is clam ped to the front. The rip fence can be used on both sides of the blade. A Danger! Start the saw only after the fol- lowing preparations have been com- p.
20 ENGLISH 7.4 Fence guide extrusion installation • Fasten the fence guide extrusion (40) with four each th umb screws and washers to the saw table. 7.
21 ENGLISH Position power supply cable so it does not interfere with the work and is not damaged. Protect power supply cable from heat, aggressive liquids and sharp edges. Use only rubber jacketed cable of suf- ficient l ead cross se ction. Do not pull on power supply cable to unplug.
22 ENGLISH 8.1 Sawing 1. Choose and insta ll a table insert extrusion suitable for the type of cut to be performed: − table insert extrusion with a nar- row slot for standard cross cuts only; − table insert extrusion with b evel- led slot for bevel cuts also.
23 ENGLISH 2. Loosen screws (61) . 3. Adjust position of guide bearing sup- port (62) so that the guide bearings (63) are positioned approx. 1 mm behind the to oth gullet. 4. Tighten screws (61) again. 5. Loosen screws (64) . 6. Press guide bearings (65) together (against the band sa w blade).
24 ENGLISH 12. Adjust thrust bearing position (78) so it just touches the band saw blade. 13. Tighten screw (79) again. 14. Reinstall the saw table on th e upper table trunnion. 15. Reinstall th e fence guide extrusion for the rip fence. 9.5 Band saw tyre replace- ment Periodically check band saw tyres for wear.
25 ENGLISH A Danger! Repairs to power tools must be carried out by qual ified electricians only! Power tools in need of repair can b e sent to the service centre of your country. Refer to the spare parts list for the address. Please attach a description of the fault to the power tool.
26 ENGLISH 15.1 Available band saw blades 15. Technical specifications Model BAS 316G DNB BAS 316G WNB Voltage V 400 (3~ 50 Hz) 230 (1~ 50 Hz) Capacity power input P1 effective shaft output P2 kW kW 0.
63 A 090 900 4276 B 090 902 9244 C 090 902 9252 D 090 902 9260 E 090 902 9279 F 090 901 8811 G 090 903 0528 H 090 903 0536 I 090 901 8366 J 091 000 8048 K 090 901 0900 L 091 003 1260 M 013 001 1004 N 431 306 2258 O 091 101 8691 45° 3 0° 0° 22,5° 30° 45° 15° 15° 22,5° U3a0151.
ZINDEL - Technische Dokumentation und Multimedia, www.zin del.de U4BA_EB3.fm www.elektra-beckum.de.
An important point after buying a device Elektra Beckum BAS 316G WNB (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Elektra Beckum BAS 316G WNB yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Elektra Beckum BAS 316G WNB - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Elektra Beckum BAS 316G WNB you will learn all the available features of the product, as well as information on its operation. The information that you get Elektra Beckum BAS 316G WNB will certainly help you make a decision on the purchase.
If you already are a holder of Elektra Beckum BAS 316G WNB, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Elektra Beckum BAS 316G WNB.
However, one of the most important roles played by the user manual is to help in solving problems with Elektra Beckum BAS 316G WNB. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Elektra Beckum BAS 316G WNB along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
