Instruction/ maintenance manual of the product U30130 21602 G Electrolux
Go to page of 28
21602 G Gas hob Operating Instructions GB.
2.
3 Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350350 Installation This hob must be installed by qualified personnel, according to the manufacturer’s instructions and to the relevant British Standards.
4 Ensure the control knobs are in the ‘OFF’ position when not in use. When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance. Unstable or misshapen pans should not be used on the hob as unstable pans can cause an accident by tipping or spillage.
5 Contents Important Safety Information ...... ..................................................................................... 3 Description of the Hob .............................................................................................
6 1. Hob T op 2. Rapid Burner 3. Semi-rapid Burners 4. Auxiliary Burner 5. Control knob for back right burner (semi-rapid) 6. Control knob for back left burner (semi-rapid) 7.
7 Hob burners control knobs The symbols on the knobs mean that : there is no gas supply there is maximum gas supply there is minimum gas supply Lighting the burners For easier lighting, proceed before putting a pan on the pan support.
8 Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool.
9 Something Not Working? If the hob is not working correctly , please carry out the following checks before contacting your local AEG-Electrolux Service Force Centre.
10 Service and Spare Parts When you contact the Service Centre, they will need the following information: 1. Y our name, address and post code. 2. Y our telephone number 3. Clear and concise details of the fault 4. The model and the serial number (see rating label on the back of this instruction booklet) 5.
11 Guarantee Conditions Standard guarantee conditions We, AEG-Electrolux, undertake that if within 12 months of the date of the purchase this AEG-Electrolux appliance or any part thereof is proved to .
12 OVERALL DIMENSIONS Width: 580 mm Depth: 500 mm CUT OUT DIMENSIONS Width: 550 mm Depth: 470 mm SUPPLY CONNECTIONS Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230 V - 50 Hz supply , 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse.
13 BURNER RAPID SEMI-RAPID AUXILIARY (large) (medium) (small) POSITION M A X M I N M A X M I N M A X M I N NOMINAL THERMAL POWER kW 3 . 0 0.65 2.0 0.45 1.0 0.33 NOMINAL FLOW RATE m 3 / h 0.286 0.057 0.190 0.038 0.095 0.028 NOZZLE REFERENCE 1 1 9 Adjust.
14 Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.
15 CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITH A COOKER HOOD ABOVE FO 0813 FO 0812 Installation IMPORTANT This hob must be installed by qualified personnel to the relevant British Standards.
16 A) End of shaft with nut B) W asher C) Elbow FO 0814 FO 0264 On the end of the shaft, which includes the G 1/2" threaded elbow , adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force.
17 Cut Out Size The dimensions of the cut-out are given in the diagram. Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface.
18 ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET FO 0763 FO 0764 1 2 Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated.
19 Fitting the hob to the worktop Before fitting the hob into the cut out, a sealing gasket supplied with the hob must be fitted to the edge of the cut out. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below .
20 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed.
21 Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations.
22 Fault Finding Preliminary Electrical Systems Check START Isolate appliance and carry out: A: Earth Continuity check. Has inlet fuse blown? Carry out: C: Polarity check. Electricity supply should now be satisfactory. Carry out: D: Resistance to Earth check.
23 A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on W (Ohms) x 1 scale and adjust zero if necessary . — T est leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 W (Ohm), check all earth wires for continuity and all contacts clean and tight.
24 Check gas supply at burner Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ig.
25 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. T o do this, follow the procedure below . 1) T urn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times.
26 Conversion from Natural Gas to LPG It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted.
27.
35678-5904 03/05 Grafiche MDM - Forlì From the Electrolux Group. The world’ s No.1 choice. The Electrolux Group is the world’ s largest producer of powered appliances for kitchen, cleaning and outdoor use.
An important point after buying a device Electrolux U30130 21602 G (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Electrolux U30130 21602 G yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Electrolux U30130 21602 G - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Electrolux U30130 21602 G you will learn all the available features of the product, as well as information on its operation. The information that you get Electrolux U30130 21602 G will certainly help you make a decision on the purchase.
If you already are a holder of Electrolux U30130 21602 G, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Electrolux U30130 21602 G.
However, one of the most important roles played by the user manual is to help in solving problems with Electrolux U30130 21602 G. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Electrolux U30130 21602 G along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
