Instruction/ maintenance manual of the product SMART 726685 Electrolux
Go to page of 28
TAVOLI REFRIGERATI E FREEZER CON CONTROLLO ELETTRONICO REFRIGERATED AND FREEZER COUNTERS WITH ELECTRONIC CONTROL TABLES RÉFRIGÉRÉES ET FREEZERS À CONTRÔLE ÉLECTRONIQUE MESAS REFRIGERADAS Y CONGELADOR CON CONTROL ELECTRÓNICO PART NO. 595R 001 01 VERSION 2 2006.
2 INSTALLATION DIAGRAM SCHEMA D’INSTALLAZIONE TAVOLO REFRIGERATO 2 VANI CON ALZATINA 2-COMPARTMENT REFRIGERATED COUNTER WITH SHOULDER TABLE RÉFRIGÉRÉE 2 COMPARTIMENTS AVEC BORD REHAUSSÉ MESA REF.
3 USA IT FR ES A = MODULAR COMPARTMENT DESIGNED FOR SOLID DOORS (WIRE SHELVES IN CELL) OR DRAWER UNIT B = MODULAR COMPARTMENT DESIGNED FOR REFRIG ERATING UNIT OR FREEZER C = OUTLET FOR DRAINING OF LIQUIDS FROM CELL, DIAMETER 0,69"/17,5 mm.
4 C I AA B A A C I INSTALLATION DIAGRAM SCHEMA D’INSTALLAZIONE TAVOLO REFRIGERATO 3 VANI CON ALZATINA 3-COMPARTMENT REFRIGERATED COUNTER WITH SHOULDER TABLE RÉFRIGÉRÉE 3 COMPARTIMENTS AVEC BORD R.
5 USA IT FR ES A = MODULAR COMPARTMENT DESIGNED FOR SOLID DOORS (WIRE SHELVES IN CELL) OR DRAWER UNIT B = MODULAR COMPARTMENT DESIGNED FOR REFRIG ERATING UNIT OR FREEZER C = OUTLET FOR DRAINING OF LIQUIDS FROM CELL, DIAMETER 0,69"/17,5 mm.
6 INSTALLATION DIAGRAM SCHEMA D’INSTALLAZIONE TAVOLO REFRIGERATO 4 VANI CON ALZATINA 4 COMPARTMENT REFRIGERATED COUNTER WITH SHOULDER SCHÉMA D’INSTALLATION DIAGRAMA DE INSTALACIÓN SIDE VIEW VIST.
7 USA IT FR ES A = MODULAR COMPARTMENT DESIGNED FOR SOLID DOORS (WIRE SHELVES IN CELL) OR DRAWER UNIT B = MODULAR COMPARTMENT DESIGNED FOR REFRIG ERATING UNIT OR FREEZER C = OUTLET FOR DRAINING OF LIQUIDS FROM CELL, DIAMETER 0,69"/17,5 mm.
8 Fig.1 PANNEAU DE COMMANDE VERSION "RÉFRIGÉRATEUR” PANEL DE CONTROL VERSIÓN "FRIGORÍFICO” 1- Access to button for food categories 2 - High humidity ON/OFF button 2a - High humidity .
9 Fig.2 “FREEZER” VERSION CONTROL PANEL PANNELLO DI CONTROLLO VERSIONE "CONGELATORE” PANNEAU DE COMMANDE VERSION "CONGÉLATEUR” PANEL DE CONTROL VERSIÓN "CONGELADOR” 1- Acces.
10 CATEGORIES: TEMPERATURE AND HUMIDITY SET- TING CATEGORIE: TEMPERATURA E IMPOSTAZIONE DELL'UMIDITA' Fig.3 REFRIGERATOR VERSIONE A TEMPERATURA NEGATIVA CATÉGORIES: TEMPÉRATURE ET PROGRAMM.
11 Fig.5 INCORRECT DISTRIBUTION OF FOOD CARICO NON CORRETTO DEGLI ALIMENTI CHARGEMENT DES ALIMENTS INCORRECT CARGA INCORRECTA DE LOS ALIMENTOS CORRECT DISTRIBUTION OF FOOD CARICO CORRETTO DEGLI ALIMEN.
12 Fig.10 FUNCTIONAL SPACES SPAZI FUNZIONALI ESPACES FONCTIONNELS ESPACIOS FUNCIONALES 74.01" 74.01" 1880 mm 1880 mm 26.38" 26.38" 670 mm 670 mm.
13 Fig.11 0 6 :4 1 * * * D e f r o st EN D 2 3 :4 1 5 2 3 :3 1 5 2 3 :2 1 5 2 3 :1 1 5 2 3 :0 1 * * * D e f r o st ST A R T 2 2 :5 1 5 E nd: 11/ 03/ 2001 22: 35 S t art: 11/ 03/ 2001 22: 32 **** P OW .
14 PRECAUTIONS ......................................................................... Page 16 A . 1 GENERAL INFORMA TION ........................................................ Page 17 A.1.1 Foreword ...............................................
15 C.1.5 Loading the product .................................................................................................... P a g e2 3 C.1.6 Defrosting .............................................................................................
16 PRECAUTIONS T o reduce the risk of fire, electric shock or injury during use of the appliance, follow these basic precautions, with particular attention to the following: • Read all instructions before using the appliance. • This Manual does not cover every possible condition and situation that may occur .
17 A 1.8 IMMEDIATE INSPECTION FOR DAMAGE DUE TO TRANSPORT Check the packing for any damage before and during unloading. The carrier is responsible for the safety of the container during transport and delivery. If the equipment received has visible or hidden damage, a claim can be made with the carrier.
18 3-COMPARTMENT REFRIGERATED COUNTER WITH SHOULDER External dimensions: - Width 69.25" 1759 mm - Depth with door closed 27.56" 700 mm - Depth with door open 43.70" 1 1 10 mm - Depth with drawers open 49.99" 1270 mm - Height 37.40" 950 mm Compartment dimensions: - Width 14.
19 WEAR PROTECTIVE GLOVES WHEN UNPACKING AND INSTALLING THE APPLIANCE. Read these instructions carefully before carrying out installation. Installation and start- up must be carried out by a qualified installer .
20 B.1.4 WATER CONNECTION The appliance is equipped with a drain hole for draining any liquids collected in the compartment. Connect the hole “C” , located on the bottom of the appliance and closed with a plug, to a special drain. The diameter of the drain hole is “0.
21 C.1.2 FIRST ST ART -UP AND TEMPERA TURE ADJUSTMENT The appliance has a main ON/OFF switch. Switch the appliance on by pressing the ON/OFF button: T o set the compartment temperature, proceed as follows: - hold the bottom SET button down for 5 seconds SET The SET TEMPERATURE value will be displayed The unit of measure light start s flashing.
22 - T o store the new set value, wait until it stops flashing and exit the program SET If no selection is made within 15 seconds, the last value displayed will be automatically confirmed and the display of compartment temperature will be updated.
23 T o select a category , press the top MANUAL DEFROST button or bottom SET button or SET after pressing the button, if no selection is made within 5 seconds the last category displayed is automatically confirmed and stored.
24 buzzer: buzzer activated WHA T IS RECORDED? Press HACCP the buzzer goes off; press again for 5 seconds until the alarm (AL1) is displayed. Press again HACCP the temperature, start date and time are given in a message: “TEMP 78.8F/26C Start 17.05 10-10-99 End——” .
25 C.1.7.4 LIST OF SERVICE ALARMS · T ype “ b ” service alarms b1 b2 b3 b4 No pow er s upply P lug not c orrec t l y ins ert ed Doo r open Mi c ros wit c h br ok en Res et t h e HA CCP m e m o ry.
26 C.2.1 Basic system connection (accessory code F880048) The printer can provide a printout of data obtained by the sensor connected to the electronic board.
27 C.3.3 SHELF MODULARITY To replace the shelf, remove the fixing screws located under the shelf, shift the shelf towards the front of the counter to release it from the rear seats, then lift it out. Routine maintenance tasks can be performed by non- specialized personnel.
28 If the fault persists after carrying out the above checks, contact T echnical Service, remembering to specify the following: • nature of the fault; • appliance PNC (production code); • Ser . No. (appliance serial number). Note: The code and serial number are essential for identifying the type of appliance and date of manufacture.
An important point after buying a device Electrolux SMART 726685 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Electrolux SMART 726685 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Electrolux SMART 726685 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Electrolux SMART 726685 you will learn all the available features of the product, as well as information on its operation. The information that you get Electrolux SMART 726685 will certainly help you make a decision on the purchase.
If you already are a holder of Electrolux SMART 726685, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Electrolux SMART 726685.
However, one of the most important roles played by the user manual is to help in solving problems with Electrolux SMART 726685. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Electrolux SMART 726685 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
