Instruction/ maintenance manual of the product EHG675 Electrolux
Go to page of 20
2 GB Gas Hob INSTR UCTION BOOKLET Models EHG 672 - EHG 674 - EHG 675 35670-2601.
3 Important Safety Infor mation You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 01635 522799 Installation ● This hob must be installed by qualified personnel, according to the manufacturer ’ s instructions and to the relevant British Standards.
4 F or the User Description of the Hob Page 5 Operation Page 6 Maintenance and Cleaning Page 7 Something Not W orking? Page 8 Service and Spare Parts Page 8 Guarantee Conditions Page 9 Electrolux Serv.
5 1. Hob T op 2. Rapid Burner 3. Semi-rapid Burners 4. Auxiliary Burner 5. Control knob for back right burner (semi-rapid) 6. Control knob for back left burner (semi-rapid) 7. Control knob for front left burner (rapid) 8. Control knob for front right burner (auxiliary) 9.
6 HOB BURNERS To light a burner, turn the relevant control knob anticlockwise to maximum position. At the same time push the electric ignition button which is marked with a little spark.. Then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again.
7 Befor e any maintenance or cleaning can be carried out, you must DISCONNECT the hob fr om the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool.
8 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local Electrolux Service Force Centre.
9 Guarantee Conditions ELECTROLUX STANDARD GUARANTEE CONDITIONS W e, Electrolux, undertake that if, within 12 months of the date of the purchase, this Electrolux appliance or any part thereof is prove.
10 CHANNEL ISLANDS GUERNSEY Guernsey Electricity PO Box 4 V ale , Guernsey Channel Islands JERSEY Jersey Electricity Company PO Box 45 Queens Road St Helier Jersey Channel Islands JE4 8NY SCOTLAND ABE.
11 MIDLANDS BIRMINGHAM 66 Birch Road East, (M18) W yrley Road Industrial Estate W itton Birmingham B67DB BOURNE Manning Road Ind (M44) Estate Pinfold Road Bourne PE10 9HT BRIDGNOR TH 1 Underhill Stree.
12 Ignition HT Spark Spark Generator Ispra Control's BF 50046 - 230-240V 0.6 Y A T 120 Spark Gap Fixed OVERALL DIMENSIONS W idth: 580 mm. Depth: 500 mm.
13 Important safety requir ements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE W iring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.
14 550 470 580 500 55 min. FO 2109 Rectangular cut-out size for hob A) End of shaft with nut B) W asher C) Elbow It is important to install the elbow corr ectly , with the shoulder on the end of the thr ead, fitted to the hob connecting pipe. Failur e to ensure the corr ect assembly will cause leakage of gas.
15 Building In a) Sealing gasket Fitting the hob to the w orktop Before fitting the hob into the cut out, an adhesive sealing gasket supplied with the hob must be fitted to the edge of the cut out. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below .
16 Electrical connections Any electrical work r equired to install this hob should be carried out by a qualified electrician or competent person, in accor dance with the current r egulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed.
17 B L N 0 1 2 3 4 220/240 A W iring diagram A. IGNITOR SWITCH B. IGNITOR UNIT.
18 Fault Finding Pr eliminar y Electrical Systems Check A. EAR TH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary . a) T est leads from any appliance earth point to earth pin on plug.
19 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check .
20 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. T o do this, follow the procedure below . - T urn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times.
21 Servicing A: Removal Of Hob Top 1. Remove all control knobs, pan supports, burner caps and crowns. 2. Remove 2 screws from each burner . 3. Lift the hob top at the rear and disengage it from the front locators. 4. Remove fixing nut from generator and earth lead to hob.
An important point after buying a device Electrolux EHG675 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Electrolux EHG675 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Electrolux EHG675 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Electrolux EHG675 you will learn all the available features of the product, as well as information on its operation. The information that you get Electrolux EHG675 will certainly help you make a decision on the purchase.
If you already are a holder of Electrolux EHG675, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Electrolux EHG675.
However, one of the most important roles played by the user manual is to help in solving problems with Electrolux EHG675. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Electrolux EHG675 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
