Instruction/ maintenance manual of the product 2.1P Electro-Voice
Go to page of 16
Electro-V oice ® EVID 12.1P User Manual.
Electro-V oice ® T able of Contents Product Description ................................................................................. 1 Product Feature Identification .................................................................. 1 Packing List .
Electro-V oice ® Product Description The 12.1P is a self cont ained, powered 12" subwoofer providing over 300 watt s continuous output to the speaker .
Electro-V oice ® Packing List Figure 4: EVID TM 12.1P Packing List 2 Below is a list of p arts included with the EVID TM 12.1P subwoofer . The part s are illustrated in Figure 4. A. EVIDTM 12.1P B. W all/Corner Mounting Bracket C. (4) Rubber Mounting Feet D.
Electro-V oice ® S tep-by-S tep Installation & Wiring S tep 1: Mount the Bracket The mounting bracket can be inst alled two ways (see Figures 5 and 6), allowing optimal configurations for installations.
Electro-V oice ® 4 Figure 7: Wiring Configuration S tep 3: Wire the Speaker A typical wiring configuration is shown in Figure 7. It is highly advisable to support the unit while these connections are being made. When mounting the speaker in a corner mount configuration, a right angle XLR connector such as Neutrik #NC3MRC or equiv .
Electro-V oice ® 5 enclosure hangs from the top clip, always inst all the lower one to secure against possible disengagement of the top clip. S traighten the EV® logo and press firmly at its center to seat it securely into it s mounting hole.
Electro-V oice ® 6 Mounting through a suspended ceiling grid On the rear of the enclosure install and tighten two 3/8-16-thread forged steel eyebolt s (one is included) with a 3/8" flat washer under each.
Electro-V oice ® 7 Safety Agency Compliance The EVID 12.1P bracket system has successfully p assed EIA 636 at a safety factor of 6:1. The bracket system is intended to support the EVID 12.1P only . Do not use it for any other purpose. Never set anything on, or hang anything from, the EVID 12.
Electro-V oice ® 8 Obtaining Warranty Service T o obtain warranty service, a customer must deliver the product, prepaid, to Electro-V oice® Service or to any of it s authorized service representatives, together with proof of purchase of the product in the form of a bill of sale or receipted invoice.
Electro-V oice ® 9 • Higher-level foreground music in bass heavy applications such as dance floors, amusement arcades, or loud bars: use one pair of EVID 6.2s for each 12.1P . • For example, a large hotel might use eight 3.2s and two 12.
Electro-V oice ® 10 Appendix C: Painting Process • Remove the four screws securing the front hatch and lift of f the hatch p anel. Carefully twist and lift off the EV® logo and set it aside. • The foam grille blocks are held in place by sharp pins protruding through the baffle board.
Electro-V oice ® 11 Appendix D: T roubleshooting Guide Problem Possible Cause(s) Action 1. No sound Amplifier V erify that that the line level signal cables XLR connector has been pushed all the way into the Low Level In jack on the amplifier panel.
Electro-V oice ® 12 Appendix E: T echnical Specifications Frequency Response (-10 dB): 42 Hz 160 Hz Max Calculated SPL 1 @ 1M: 126 dB LF Amplifier Power: 650W 50ms Burst, 300W Continuous Line Inp.
Electro-V oice ® 13 Notes.
Electro-V oice ® U.S.A. and Canada: For customer orders, contact the Customer Service department at: 800/392-3497 Fax: 800/955-6831 For warranty repair or service information, contact the Service Rep.
An important point after buying a device Electro-Voice 2.1P (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Electro-Voice 2.1P yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Electro-Voice 2.1P - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Electro-Voice 2.1P you will learn all the available features of the product, as well as information on its operation. The information that you get Electro-Voice 2.1P will certainly help you make a decision on the purchase.
If you already are a holder of Electro-Voice 2.1P, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Electro-Voice 2.1P.
However, one of the most important roles played by the user manual is to help in solving problems with Electro-Voice 2.1P. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Electro-Voice 2.1P along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
